• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1387-1388
• /
• 1997

The MCFC has conspicuous feature and high potential in being used as an energy converter of various fuel to electricity and heat. However, the MCFC which use strongly corrosive molten carbonate at $650^{\circ}C$ have many problem. Systematic investigation on corrosion behavior of Fe/20Cr/Ti alloys has been done in (62+38)mol% (Li+K)CO3 melt at 923K by using steady state polarization and electrochemical impedance spectroscopy method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.220-223
• /
• 2009

Metallic bipolar plate for molten carbonate fuel cell(MCFC) is composed of the shielded slot plate and the center plate. Among these, the center plate plays an important role in gas sealing. Therefore, manufacturing of the center plate is considered one of the key issues in MCFC. The center plate is manufactured by bending process. In bending process, springback and recoiling are two main problems. By using the modified punch shape with 'step', springback and recoil are reduced. The aim of this article is to find the effect of modified punch shape. So, the bending stress along thickness direction and material direction were investigated using FEM.

• Journal of the Korean Professional Engineers Association
• /
• v.44 no.1
• /
• pp.48-52
• /
• 2011

The KEPCO Research Institute has developed Molten Carbonate Fuel Cell(MCFC) since 1993. Recently, an 125-kW MCFC system was operated at Boryeong thermal power plant, Korea from December, 2009 to March, 2010, This system is composed of an 125-kW stack, mechanical balance of plant (MBOP), and Power Conditioning System. The stack has 200 unit cells of which effective area is 10,000 cm2. Especially, MBOP is mainly made up of ejector and catalytic combustor which help this system to be supplied with cathode inlet gas using anode tail gas and fresh air. After the pretreatment of this system was performed for about 20 days, initial load operation was performed at January. 2010. Moreover, this system had been operated for 3,270 hours.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.11
• /
• pp.1021-1027
• /
• 2004

Design performances of various configurations of hybrid systems combining an atmospheric pressure molten carbonate fuel cell and a gas turbine have been analyzed. Two different fuel reforming methods (internal and external reforming) were considered. Influences of turbine inflow heating method, location of fuel combustor and associated component arrangements were investigated. In general, internal reforming leads to higher system efficiencies. The optimum design pressure ratio varies among different system configurations. In particular, the design point selection is closely related to the allowable turbine inlet temperature. Configurations with direct heating of turbine inlet flow may realize both higher efficiency and higher specific power than those with indirect heating.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.195-196
• /
• 2007

This paper shortly describe the R&D results for developing of 250 kW externally reforming MCFC (Molten Carbonate Fuel Cell) CHP proto type. Conceptual Design and basic design were alredy completed and stack which was adapted new separator and components also prepared for operation and evaluation. In parallel with stack and system development, BOP such as PCS, blower, catalytic combustor and Reformer also designed and fabricated for evaluation. The system will be fabricated by the end of 2008 and operate and evaluate in 2009.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.3
• /
• pp.178-182
• /
• 2003

The oxygen reduction and NiO dissolution behaviors in Li-Na-K three component carbonate melts have been investigated with various compositions through electrochemical and chemical ways. The oxygen reduction currents and NiO solubilities were measured at $650^{\circ}C$ and atmospheric condition in Li-Na-K =47.4-32.6-20, 60-20-20, 50-40-10, $40-40-20 mol\%$ carbonate melts. The oxygen reduction currents showed dependence on the composition, indicating oxygen solubility is a function of carbonate composition. At the composition of $ Li-Na-K=50-40-10 mol%$, a broader peak was observed, suggesting different oxygen reduction mechanism probably prevails in this composition. In contrast, insignificant differences of NiO solubility were obtained among the compositions.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.3
• /
• pp.124-131
• /
• 2006

For commercialization of molten carbonate fuel cell (MCFC), it has some problems to be overcome such as decrease of porosity and thickness of the anode under the operating condition (at $650^{\circ}C$ and working pressure of more than 2 $kg_f/cm^2$). Recently, Ni-Al alloy anode has been proposed to replace the conventional Ni-Cr anode as an alternative material to resist a creep and inhibit the sintering. The objective of this research is to sinter the green sheet of Ni-Al alloy anode during single cell pre-treatment process, which has several advantages like cost down and simplification of manufacturing process. However, the Ni-Al alloy anode prepared with a conventional pre-treatment process showed the phase separation of Ni-Al alloy and formation of micropore(${\leqq}0.4{\mu}m$), resulting in low creep resistance and high electrolyte re-distribution. In order to prevent the Ni-Al alloy anode from phase-separating, nitrogen gas was used in the process of pre-treatment. Introducing the nitrogen, the phase separation from Ni-Al alloy into nickel and alumina was minimized and increased creep resistance. However, there was some micropore formation on the surface of Ni-Al alloy anode during the cell operation due to creation of lithium aluminate. Addition of more amount of electrolyte into a cell, especially at cathode, made the cell performance stable for 2,000 hrs. Consequently, it was possible to make the Ni-Al alloy anode with good creep resistance by the modified in-situ sintering technique.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.132.1-132.1
• /
• 2010

Anode off-gas of high temperature fuel cells such as MCFC still contain combustible components such as hydrogen, carbon monoxide and hydrocarbon. Thus, it's very important to fully burn anode off-gas and use the generated heat in order to increase system efficiency. In the present study, catalytic combustors have been applied to high temperature MCFC system so that the combustion of anode-off gas can be boosted up. Since the performance of catalytic combustor directly depends on the combustion catalyst, this study has been focused on the experimental investigation on the combustion characteristics of multiple commercial catalysts having different structures and compositions. In order to determine the design conditions of the catalytic combustor, parameters such as inlet temperature, space velocity and excess air ratio have been varied and optimized for combustor design. Results show that $H_2$ in off-gas assists $CH_4$ combustion in a way that it decreases minimum inlet temperature limit and increases maximum space velocity while keeping high fuel conversion efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.117-120
• /
• 2007

Fuel cells are currently attracting tremendous interest because of their huge potential in stationary applications, in terms of substantiality of our energy use. They also offer environmental advantages, combining significantly higher efficiency with very much lower emission of SOx, NOx, and residual hydrocarbons, and significantly reduced $CO_{2}$ emissions compared to conventional power generation. The molten carbonate fuel cell (MCFC) was introduced from Fuel Cell Energy(FCE), which the one MCFC was operating by LNG and the other was operating by ADG. The ADG contains normally CH4, CO2 and various impurities such as sulfur compounds and siloxanes. Using the ADG as a fuel, MCFC have the potential to provide significant environmental and economic benefits. However, such impurities would be harmful to fuel cells. In this work, a purification process for the ADG was designed and installed in order to utilize the gas as a fuel for MCFC.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.92.1-92.1
• /
• 2011

Anode off-gas of high temperature fuel cells such as MCFC contains a significant amount of combustible components like hydrogen, carbon monoxide and methane according to fuel utilization ratio of the fuel cell stack. Thus, it is important to fully burn anode off-gas and utilize the generated heat in order to increase system efficiency and reduce emissions as well. In the present study, 25 kW catalytic combustor has been developed for the application to a load-following 300kW MCFC system. Mixing and combustion characteristics have been experimentally investigated with the catalytic combustor. Since the performance of catalytic combustor directly depends on the combustion catalyst, this study has been focused on the experimental investigation on the combustion characteristics of multiple catalysts having different structures and compositions. Results show that the exhaust emissions are highly dependent on the catalyst loading and the ratio of catalytic components. Test results at load-following conditions are also shown in the present study.