• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.335-343
• /
• 2002

Blend resin (PET/PETG 70/30 blend) of poly (ethylene terephthalate) (PET) and poly (ethylene terephthalate glycol) (PETG) of weight percent 70/30 was prepared by a twin-screw extruder. Undrawn films of the blend and pure PETG were made by melt-press in hot press. Drawn films were made by capillary rheometer. Crystallinity, shrinkage, thermal, dynamic mechanical, and mechanical properties of these blends and PETG drawn films were investigated by wide angle X-ray diffractometer, dry oven, DSC thermal analyzer, and tensile tester. The crystallinity and density of these films increased with increasing draw ratio and draw rate but decreased with increasing draw temperature. The crystallinity and density of the blend films were higher than those of PETG films. The tensile strength and tensile modulus of these drawn alms increased with increasing draw ratio and draw rate but decreased with increasing draw temperature. The tensile strength and tensile modulus of blend films were higher than those of PETG films. Shrinkage of PETG md blend films decreased with draw ratio and draw rate. Shrinkage of undrawn blend film was 600% higher than that of pure PET film.

• Composites Research
• /
• v.31 no.2
• /
• pp.63-68
• /
• 2018

Thermoplastic composite has been limitedly used in high performance aerospace industry due to relatively low mechanical properties even though it has various advantages. But, thermoplastic aromatic polymer composite has recently been researched and utilized much. In this study, PEEK and PPS neat resin film as representative thermoplastic aromatic polymer were processed through continuous heating, cooling and reheating cycle. Property change such as glass transition temperature and melting temperature were identified and crystallinity variation by different cooling rate were evaluated. In the first (heating) run, polymer specimens were kept for 5 minutes at higher temperature than melting point to remove previous thermal history, and crystallization reaction was controlled by adjusting cooling rate to 2, 5, 10, 20 and $40^{\circ}C/minute$ in the second (cooling) run. In the third (heating) run, specimen crystallinity were verified by measuring the melting enthalpy. The initial specimens containing high portion of amorphous structure exhibited cold crystallization and clear glass transition in the first run whereas they did not show in the third run due to the increase of crystalline structure portion. As cooling rate decreases through the second cooling run, the crystallinity of the specimen increased. PEEK polymer had 21.9~39.3% crystallinity depending on cooling rate change whereas PPS polymer showed 29.1~31.2%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.610-615
• /
• 2016

Diverse accessories are used in automobiles, such as navigation systems, front and rear cameras, spoilers, and sun visors. Sun visors block sunlight so that drivers can drive safely with a better view, and they are used in many automobile designs. However, when large plastic products are manufactured using injection molding, there are many difficulties that develop, like weld lines, short shots, flow marks, imperfections, and distortion. In this study, a CAE simulation was conducted based on previous results to predict potential problems in the injection molding of large products. The flow characteristics up to complete charge for the melting resins were captured using a computer-aided engineering simulation. The temperature departure on the front part of a flow was about $10^{\circ}C$ and very stable. The practical ejecting time of the cold runner was about 70 seconds in the simulation. Finally, the capability of a suitable injection machine was calculated and recommended by prediction of the injection pressure and the die clamping force.

• Composites Research
• /
• v.16 no.1
• /
• pp.19-25
• /
• 2003

In this paper, electrical properties of nanostructured carbon blacks (CB)-filled high density polyethylene (HDPE) composites were investigated as a function of temperature, which were prepared by the conventional melt-mixing method. The composites were irradiated with electron beam in a dosage of 30∼150 kGy to enhance an electronical reproducibility and to reduce a negative temperature coefficient (NTC) phenomenon. And, gel contents (%) of irradiated CB/HDPE composites were estimated by solvent extraction method. From the experimental results. the positive temperature coefficient (PTC) intensity of the composites was strongly depended on the CB content and particle size. And, the increase of gel contents (%) and disappearance of NTC behavior of the composites were identified at a dosage of 60 kGy. It was also found that the electron beam irradiation made an improvement of electrical reproducibility of the composites. This result was probably due to the reduction of the freedom of CB movement at above the melting temperature of the polymer crystalline, resulting in increasing the crosslinking structure of the composites.

• The Korean Journal of Rheology
• /
• v.2 no.2
• /
• pp.56-65
• /
• 1990

열방성 액정고분자와 폴리카보네이트를 대상 수지로 하여 용융혼합기로 액정고분자 의 함량, 혼합속도 및 온도등의 변환에 따른 훈련 특성을 측정하고 고분자 혼합물의 혼련조 건과 유변학적 특성 모폴로지 사이의 관계를 조사하였다. 혼련 토크는 100rpm의 혼합속도 에서 극소값을 보이며 혼합기 내의 전단속도가 낮기 때문에 혼력에의해서는 LCP가 섬유상 으로 형성되지 못하고 구형의 입자로 존재함을 알수 있었다. 혼합물의 점도는 시험된 전단 속도 영역에서 순수한 고분자보다 현저히 낮으며 5wt%의 소량 첨가로도 5배의 점도 감소 효과를 보이고 LCP함량이 약 30wt%일 경우 점도 및 혼합에너지가 최소로 되었다. Capillary 레오미터의 실험결과 LCP/PC의 점도비가 1보다 작거나 같튼 전단장하에서 LCP 는 섬유상을 형성하였으며 높은 점도비의 경우 LCP의 변형이 어려워 구형의 입자로 존재하 였다. 또한 혼합물의 PC Tg 이동은 에스터르 교환 반응에 의한 부분적인 혼화성의 증가에 기인함을 알수 있었다.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.226-231
• /
• 1998

Hot melt adhesive which is solventless type has been widely used due to the possibility of automated adhesion process. The main purpose of this study is the development of polyamide based hot melt adhesive to improve the property of conventional ethylene-vinyl acetate hot melt adhesive, which has an inherent problem against heat resistance. In this study, it was found that the terpolymers of nylon 6, nylon 66, and nylon 12(CM831, 843P types) instead of nylon homopolymer were suitable base resins for hot melt adhesive, since the disruption of regularity in the polymer chains reduced the crystallinity, resulting in lower melting point and melt viscosity. According to the results, the optimum adhesion property could be obtained by the using 75/25~50/50 weight radio of CM831/843P resin as a base resin. Terpene resin was used as tackifier to improve adhesion and wetting properties. The best result can be obtained with the 10 wt.% addition of terpene resin. The terpene resin acted as proper tackifier in this system which decreased the melt temperature and viscosity, but increased the mechanical strength of adhesive itself. Also, the rheological property of the adhesive changed from typical non-Newtonian behavior to Newtonian behavior as terpene resin was added.

• Polymer(Korea)
• /
• v.28 no.5
• /
• pp.374-381
• /
• 2004

Gas permeability of low density polyethylene (LDPE) film containing zeolite powder for $CO_2,\;O_2$ and $N_2$ were investigated. Zeolite powders modified by cations or surfactant were compounded with LDPE to produce $20 wt\%$ masterbatch. After blending the masterbatch with LDPE, zeolite filled films were prepared by the blown film process. Finally, the composite films containing zeolite loadings of 0, 3,5, and $10 wt\%$ were produced. A gas permeability apparatus based on the variable volume principle was designed to analyze the characteristics of films. Experiments showed a general trend that gas permeabilities first decreased and then increased as the zeolite content was increased. Surfactant modified zeolite showed a better interfacial adhesion with the matrix, but the film did not show a discernible difference in gas permeability compared with the other modified films. The difference of temperature dependences in the gas permeabilities of composite films was slightly smaller than that of LDPE film.

• Solar Energy
• /
• v.13 no.2_3
• /
• pp.53-64
• /
• 1993

This study investigated heat transfer phenomena during the freezing of an initially superheated or non-superheated liquid in a cooled cylinder tube. Numerical and experimental method were performed to obtatin the temperature and velocity distribution, the shape of interface. Natural convection effects in the superheated liquid were confined and moderated a short freezing time. After natural convection ceases, heat conduction dominated in the whole paraffin, so Crystal and much-zone were found out in PCM. Initial superheating of liquid tended to morderatly diminish the frozen layer thickness at short freezing times but little effect on the these quantities at longer times. On the amount of frozen mass, Iintial liquid superheating is less affected than tube wall subcooling.

• Fire Science and Engineering
• /
• v.16 no.1
• /
• pp.39-44
• /
• 2002

In this paper, we analysed the flame patterns and the electrical characteristics of the electric outlet which was fired at standby mode. The carbonized patterns indicated that the flame had spread about 50 cm to 70 cm. After the combustibles on wall started to burn, the temperature went up to about $300^{\circ}c$ in 150 sec. The flame formed ceiling jet and spread quickly. The tracking was generated at the shortest distance between two electrodes and the resistance was about 100$\Omega$ to 300$\Omega$ As the result of analysis using metallurgical microscope, the normal part of a blade holder showed amorphous structure, but the melted part of a blade holder damaged by tracking showed dendrite structure and void evenly. When the blade holder of damaged outlet was analyzed by SEM and EDX, we found that the structure and components of the normal part were different from those of melted part.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.125-131
• /
• 2011

The effects of chopped kenaf fiber concentration on mechanical property of polypropylene (PP) composite are investigated. The addition of kenaf increased the tensile strength, flexural modulus, impact strength, specific gravity, and HDT, while decreased the elongation%, flexural strength, and melt flow index. The increase of mechanical properties is due to increased surface area contacting between fiber and polymer matrix and fiber-fiber interaction. Volatile extractives in the kenaf seemed to decrease the interfacial adhesion between kenaf surface and PP.