• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2337-2342
• /
• 2010

There is a vast field of application for RFID(Radio Frequency IDentification) technology. In the case of hospitals, RFID can be used for organizing patient data. Generally, patient data has been handled with medical cards. In order to look up data about a patient, the medical card would have to be found first, within a lot of other medical cards, by hand or with a computer. This is a very inconvenient system. Also, if the card is searched by the name of the patient, fatal medical accidents may occur in cases of mix-ups. If remote RFID Tag monitoring systems are applied in this case, the patient data would be accessible in the hospital. This article will discuss the grafting of RFID systems and wireless data communicating technology. The EM4095 chip, which uses 125KHz carrier waves was used in this study. And a Bluetooth module was added for wireless data communication. The ATMEGA128 microcomputer was used to control the RFID system and wireless module. A LCD monitor was connected to the extension port for nurses to view patient data, and also, the same information was displayed on PC monitors for doctors to see. The circuit was designed to consume minimal amounts of electricity for portability, and to transmit Tag ID's in environments with a lot of noise. The article is concluded with a diagram of the whole system, and performance of each data transmitting section has been analyzed.

• Economic and Environmental Geology
• /
• v.45 no.4
• /
• pp.377-384
• /
• 2012

The main field component of the Earth's magnetic field was modeled from the tri-axial magnetometer onboard KOrean MultiPurpose SATellite-II (KOMPSAT-II) for the purpose of satellite attitude control. The model computed by the KOMPSAT-II magnetometer measurement data is compared with the International Geomagnetic Reference Field (IGRF) model of a degree of up to 13 in spherical harmonic coefficients. The previous study with KOMPSAT-I (Kim et al. 2004) indicated a good correlation of power spectrum of spherical harmonic coefficients with respect to the degree up to 5. This study, however, showed an agreement of the degree up to 8-9 of the coefficient power spectrum and a discrepancy between degrees 10 and 13. We have concluded that relevant data selection process, removal of the external field from the data in the high latitude region, an accuracy of the magnetometer all play an important role in finding a coherence with the IGRF model. This study will be extended to the secular variation model of geomagnetism if longer-period data become available.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.66-73
• /
• 2020

In the hydrogen compression cycle, which is currently being developed, hydrogen is compressed to a very high pressure using a compressor, and then stored and used in a high-pressure vessel. This shows that an increase in the temperature of hydrogen in the vessel due to a pressure rise during the filling process and the pressure fatigue due to the repeated cycle may cause problems in the reliability of the vessel. In this paper, for the entire processes in a 50 MPa hydrogen compression system, theoretical and numerical methods were conducted to analyze the following: the temperature increase of hydrogen in the vessel and the time required to reach thermal equilibrium with the surroundings, the change in temperature of hydrogen passing through the pressure reducing valve, and the required capacity of the heat exchanger for cooling the vessel. The results will be useful for the design and construction of hydrogen compression systems, such as hydrogen charging stations.

• Journal of Korean Ophthalmic Optics Society
• /
• v.16 no.2
• /
• pp.107-115
• /
• 2011

Purpose: To design and fabricate the distributed auto edging machine for the development. Methods: We got the necessary data needed in design by using CAD. Based on the these data, we fabricated the trial product for the development of the distributed auto edging machine. Results: The patternless mode could be operated by receiving the eyesize data from the auto lay-outer with the RS232C transmission system and the pattern mode could be operated by setting the pattern on the left side of the machine. The distributed auto edging machine were composed with combinations of many elements; head, auto arm, pattern clamp and grinding wheels. The head part controlled the grinding of ophthalmic lens by operating the vertical and horizontal motors. The wheels part was comprised of glass mode, plastic mode, V-bevel mode and polish mode. The slide in the auto arm was equipped on the below of the patten and the slide could hold up the pattern which was rotated by fixed shaft. The pattern clamp could move the head part to the up and down or right or left way by the manual operation of optometrists. Conclusions: We could succeed in making the trial product by applying it to the development of the distributed auto edging machine which could be used as the patternless mode and pattern mode, selectively. Therefore, it was confidently expected that this product was very helpful for the optometrists to dispense the ophthalmic lens because of its cost-efficiency and convenience.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.6
• /
• pp.811-823
• /
• 2019

Slip form method is applied to many cases of a shaft these days because it is safer, more economical and faster than cast-in-place method. Slip-up height of the method is approximately 2.5 to 4.0 m/day. If the temperature of concrete is outside the range of 10 to 30℃, the effects of changes in strength or elastic characteristics are significant. Therefore, it is difficult for slip-up speed to be higher than 3 m/day during winter construction. In addition, concrete has heat caused by hydration, which causes temperature cracking of hardened concrete. Therefore, temperature control of concrete curing is necessary for the continuous slip-up of slip form. In this study, the rebound hardness, time of ultrasonic waves propagation, heat of hydration, and external temperature are measured by developing heating panels and test devices for the continuous slip-up. Based on this, heating slip form is manufactured; this was applied to "Kimpo sites" and "Sinwol sites". The compared slip-up speed samples were 1.9 m/day or 0.200 m/hr on average at Gimpo sites (08:00~17:30) and 2.0 m/day or 0.210 m/hr at Sinwol sites.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.25-33
• /
• 2018

Renewable energy has been of interests in the area of modern alternative fuels. Biogas is produced in waste landfill sites through anaerobic digestion processes, including hydrolysis, acidogenesis, organic acid fermentation (acetogenesis), and methane fermentation (methanogenesis). High contents of fine dust and moisture limited its utilization for direct combustion, town gas and vehicle fuel. Thus, this study proposed a new design for a cooling device using a centrifugal cyclone for simultaneous removal of fine dust and moisture as a pretreatment in the purification processes. A heat exchanger and an ID fan, which are installed inside and outside of the cyclone, in order to cool the humid gas below the freezing point and form a foggy mist. Such an atmosphere enhanced to capture fine dust as recirculating the cold mist flow. The water removal rate was 80.8% at a relative humidity of 95%, and the particle removal efficiency was 98.3% for $2.5{\mu}m$. Simultaneous removal efficiency was 70.8% and 99.6% for particle and moisture respectively.

• Journal of Conservation Science
• /
• v.27 no.2
• /
• pp.201-209
• /
• 2011

While consolidants based on tetraethoxysilane (TEOS) have been widely used for the consolidation of decaying stone heritages, TEOS-based consolidants suffer from practical drawbacks, such as crack formation of the gel during the drying phase due to the developed capillary force. We have prepared new TEOS-based consolidants containing flexible (3-glycidoxypropyl) trimethoxysilane (GPTMS) in order to reduce capillary force development during gel drying. In this study, we have prepared TEOS/GPTMS-based consolidants containing ETEOS in order to improve the surface hydrophobisity. The physical properties of the TEOS/GPTMS/ETEOS solution with different hydrolysis were compared with those of the commercial products Wacker OH$^{(R)}$. The contact angle of the surface increased with the addition of the ETEOS, which is higher than that of Wacker OH$^{(R)}$. The sol-gel mechanism was manipulated by the degree of hydrolysis as well as the amount of ETEOS. The properties and the applicability of the developed consolidants for the decayed Korean granites are also investigated.

• Journal of Astronomy and Space Sciences
• /
• v.26 no.3
• /
• pp.403-416
• /
• 2009

COMS (Communication, Ocean and Meteorological Satellite) is a geostationary satellite and developed by KARl for communication, ocean and meteorological observations. It will be tested under vacuum and very low temperature conditions in order to verify thermal design of COMS. The test will be performed by using KARI large thermal vacuum chamber, which was developed by KARI, and the COMS will be the first flight satellite tested in this chamber. The purposes of thermal balance test are to correlate analytical model used for design evaluation and predicting temperatures, and to verify and adjust thermal control concept. KARI has plan to use heating plates to simulate space hot condition especially for radiator panels of satellite such as north and south panels. They will be controlled from 90 K to 273 K by circulating GN2 and LN2 alternatively according to the test phases, while the main shroud of the vacuum chamber will be under constant temperature, 90 K, during all thermal balance test. This paper presents thermal modelling including test chamber, heating plates and the satellite without solar array wing and Ka-band reflectors and discusses temperature prediction during thermal balance test.

• Journal of Advanced Navigation Technology
• /
• v.15 no.6
• /
• pp.1000-1007
• /
• 2011

Home Networking will be implementing the interactive network by home appliances over wireless/wireline network framwork. That is, Home appliances, which are being operated within home space configure the network through wireline/wireless network infrastructure for interworking and interacitive services by external internet access. Based on home networking, smarthome is home space where can use automatic telecommunication and interactive service by home appliances. we can call smarthome based on home networking infrastructure as the conceptual gateway for evolving future converged space like u-city. From simple home control service to home automation service over home networking infrastructure, smarthome service is evolving to up-to-date intelligent life environment in growth of IT technology. however, its service model development was based on supplier-centered based on advanced IT technology. because of this situation, smarthome service has not been acknowledged IT underprivileged people as well as IT early-adaptor. so, this research paper will consider and try to find out what will be the feasible factors to make the best service for IT underprivileged people.

• Proceedings of the Korea Multimedia Society Conference
• /
• 1998.10a
• /
• pp.149-154
• /
• 1998

본 논문에서는 월드와이드웹상에서 3차원 인터페이스를 기술하는 표준 사양인 VRML과 자바의 EAI(External Authoring Interface)를 통하여 사용자 간에 발생하는 상호작용들을 동기화 시키는 방법을 소개한다. 제시한 방법에서는 별도의 독립적인 응용프로그램을 작성하거나 동기화를 위하여 확장된 VRML을 사용할 필요없이 웹브라우저와 바로 호환하여 사용할 수 있으며 기존의 방대한 웹문서와 연계가 쉬우므로 범용적인 자료구축이 가능하다. 하지만, 가장 최근의 VRML97에서조차도 VRML이 제시하는 가상공간 다중 사용자 환경의 지원은 아직 미비하다. 더 이상 단순히 3차원 월드를 탐험하는 시기는 지났으며, 같은 공간상에서 혼자가 아닌 여럿이 함께 하는 다중 사용자 환경을 제공해야 할 것이다. 이에 자바의 네트웍 기능과 가상공간의 외부에서 동적으로 월드를 제어할 수 있는 EAI를 이용하여 부족했던 다중 사용자 환경을 지원함으로써 가상 공간 시스템을 구축할 수 있다. 그러나, 가상 공간에서 일어나는 이벤트는 단지 동일 브라우저에서만 유효하기 때문에 다른 사용자에게 전달할 때는 이벤트를 원격지의 이벤트와 연동하기 위하여 다른 방법이 필요하다. 사용자 상호작용 시스템에 있어서 이러한 이벤트를 결정하는 가장 중요한 요소는 아바타의 행동양식(avatar's behavior)이라 할 수 있다. 가상 공간에서 일어나는 이벤트의 대부분이 사용자에 의해서 발생되는 것들이다. 즉, 아바타의 행위에 따라서 사용자 서로 간에 상호작용이 일어나게 되며 이들 이벤트를 서로 동기화 함으로써 실시간 3차원 상호작용 시스템을 구현한다. 이렇게 구현된 시스템을 구현한다. 이렇게 구현된 시스템은 전자 상거래, 가상 쇼핑몰, 가상 전시화, 또는 3차원 게임이나 가상교육 시스템과 같은 웹기반 응용프로그램에 사용될 수 있다.물을 보존·관리하는 것이 필요하다. 이는 도서관의 기능만으로는 감당하기 어렵기 때문에 대학정보화의 센터로서의 도서관과 공공기록물 전문 담당자로서의 대학아카이브즈가 함께 하여 대학의 공식적인 직무 관련 업무를 원활하게 지원하고, 그럼으로써 양 기관의 위상을 높이는 상승효과를 낼 수 있다.하여는, 인쇄된 일차적 정보자료의 검색방법등을 개선하고, 나아가서는 법령과 판례정보를 위한 효율적인 시스템을 구축하며, 뿐만 아니라 이용자의 요구에 충분히 대처할 수 잇는 도서관으로 변화되는 것이다. 이와 함께 가장 중요한 것은 법과대학과 사법연수원에서 법학 연구방법에 관한 강좌를 개설하여 각종 법률정보원의 활용 내지 도서관 이용방법에 관하여 교육하는 것이다.글을 연구하고, 그 결과에 의존하여서 우리의 실제의 생활에 사용하는 $\boxDr$한국어사전$\boxUl$등을 만드는 과정에서, 어떤 의미에서 실험되었다고 말할 수가 있는 언어과학의 연구의 결과에 의존하여서 수행되는 철학적인 작업이다. 여기에서는 하나의 철학적인 연구의 시작으로 받아들여지는 이 의미분석의 문제를 반성하여 본다. 것이 필요하다고 사료된다.크기에 의존하며, 또한 이러한 영향은 $(Ti_{1-x}AI_{x})N$ 피막에 존재하는 AI의 함량이 높고, 초기에 증착된 막의 업자 크기가 작을 수록 클 것으로 여겨진다. 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$순응