• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.265-269
• /
• 2005

본 논문에서는 최대 견인력 제어를 위해서 최소 차원 부하 토크 외란 관측기를 이용하여 점착력 계수를 추정하고 추정한 점착력 계수의 미분치를 PI 토크 제어하는 Anti-slip제어를 제안한다. 최소차원 부하 토크 외란 관측기는 회전자의 위치 정보와 토크 전류의 정보를 이용하여 부하 외란토크를 추정하고, 부하 외란 토크에 철도차량 상수를 이용하여 점착력 계수를 추정한다. 또한 부하토크외란 관측기는 구조가 간단하며, 시스템의 외란 및 각종 제어이득, 시스템의 상수 변화에 대해서도 견실한 견인력 제어 특성을 가지고 있다. 이와 같은 시스템의 모델링과 전동기 토크에 대한 회전자의 위치 정보를 이용하여 최소차원 부하 토크 외란 관측기의 상태변수인 점착력 계수를 추정하고, 추정한 점착력 계수의 미분치를 PI토크 Anti-Slip제어하여, 최대 견인력 제어가 되도록 하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.366-374
• /
• 2003

In electric motor coaches, the rolling stocks move by the adhesive effort between rail and driving wheel. Generally, the adhesive effort is defined by the function of both the weight of electric motor coach and the adhesive effort between rails and driving wheel. The characteristics of adhesive effort is strongly affected by the conditions between rails and driving wheel. When the adhesive effort decreases suddenly, the electric motor coach has slip phenomena. This paper proposes a re-adhesion control algorithm which uses the maximum adhesive effort by instantaneous estimation of adhesion force using load torque disturbance observer. Based on this estimated adhesive effort, the re-adhesion control Is peformed to obtain the maximum transfer of the tractive effort.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.7-9
• /
• 2019

이 논문은 이관성 시스템에서 능동 외란 제거 제어(Active Disturbance Rejection Control, ADRC) 기반의 진동 저감 알고리즘을 제안한다. 제안한 방법은 축소 차원 ADRC를 기반으로 구성하였다. ADRC 이론에 기반한 제어 이론은 전체 토크 중 전동기 측의 관성 모멘트에 대한 토크를 제외한 모든 토크를 외란 성분이라 설정한다. 외란에 대한 가속도 성분을 전체 외란(Total Disturbance)이라고 설정하고, 이를 추정하여 보상한다. 축소 차원 ADRC의 차수가 낮아서, 축소 차원 ADRC의 대역폭을 기존 ADRC의 대역폭보다 크게 설정할 수 있다. 그리고, 증가한 이득과 실질적인 구현을 고려하여, 이산 시간 영역에서 설계하였다. 제안된 알고리즘의 안정도를 확보하고, 성능을 높이기 위하여, 추정하는 제정수의 값을 실제 값보다 작게 설정하였다. 제안한 방법은 기계시스템의 공진에 의한 영향을 감쇄시킬 수 있다. 제안한 방법을 검증하기 위해, 시뮬레이션과 실험을 수행하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.4
• /
• pp.298-307
• /
• 2016

Attitude determination of satellite is categorized by deterministic and recursive method. The recursive algorithm using Kalman filter is widely used. Cubesat has limitation for payload to minimize then only two attitude sensors are installed which are sun sensor and magnetometer. Sun sensor measurements are useless during eclipse, however cubesat keeps estimating attitude to complete the successful mission. In this paper, Attitude determination algorithm based on Kalman filter is developed by additional term which considering the dynamics for SNUSAT-1 with disturbance torque. Verification of attitude accuracy of the algorithm is conducted during eclipse. Attitude determination algorithm is simulated to compare the performance between typical method and proposed algorithm. In addition, Attitude errors are analysed with various magnitude of disturbance torque caused by space environment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.58-66
• /
• 2009

In this paper, vector control to applied disturbance offset feedforward loop control for changing disturbances with various mechanical parameter is suggested. The proposed system estimate load torque based on induction motor torque using minimum diemension state observer. Because speed controller using state observer is used on condition of feedforward loop fur a torque, the robust speed control system realized. In this study, the proposed paper does to heighten reliability of system by presuming and use the speed by voltage and current that is detected without speed sensor. To prove the propriety of this paper, the various simulation carried out adequacy using a Matlab Simulink, and at the same time real system is made, using a ADMC300 digital signal processor, so it is proved. As the experimental result of embodying the system, the robust system is realized.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.2
• /
• pp.131-136
• /
• 2006

This paper described a robust control of an induction motor using a disturbance cancellation observer of a feedforward control with Matlab simulink. The speed response of conventional PI controller characteristics is affected by variation of load torque disturbance. In this system, the speed control characteristics using a feedforward control toughen about a load torque disturbance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.42-49
• /
• 2004

This paper presents a new method of external load disturbance compensation using deadbeat load torque observer and gain compensation by parameter estimator. The response of the permanent magnet synchronous motor(PMSM) follows the nominal plant. The load torque compensation method is composed of a deadbeat observer. To reduce the noise effect, the post-filter implemented by moving average(MA) process is adopted. The parameter compensator with recursive least square method(RLSM) parameter estimator is suggested to make the new system work as same as the name plate system which in used to take gains. The proposed estimator is combined with a high performance load torque observer to resolve the problems. As a result, the proposed control system has a robust and precise system against the load torque and the parameter variation. A stability and usefulness are verified by computer simulation and experiment.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.70-79
• /
• 2005

In this paper, improvement method of control performance by a full-order observer using reduced-order state equation is proposed in the low speed range. Full-order observer using reduced-order state equation is the motor speed and the disturbance torque observer. The proposed algorithm is very stable in the low speed range about 1.9[rpm]. The disturbance torque in the motor drive system degrades speed control performance in the low speed range. The proposed algorithm estimated both motor speed and disturbance torque. The estimated disturbance torque is used as a feedforward value in output of the speed controller, As a result, it improves the response of load torque in the low speed range(1.9rpm).

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.6
• /
• pp.635-642
• /
• 2004

In electric motor coaches. the rolling stocks move by the adhesive effort between rail and driving wheel. Generally, the adhesive effort is defined by the function of both the weight of electric motor coach and the adhesive effort between rails and driving wheel. The characteristics of adhesive effort is strongly affected by the conditions between rails and driving wheel. When the adhesive effort decreases suddenly, the electric motor coach has slip phenomena. This paper proposes a re-adhesion control based on disturbance observer and sensor-less vector control. The numerical simulation and experimental results point out that the proposed readhesion control system has the desired driving wheel torque response for the tested bogie system of electric coach. Based on this estimated adhesive effort, the re-adhesion control is performed to obtain the maximum transfer of the tractive effort.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1064-1071
• /
• 2006

In electric motor coaches, the rolling stocks move by the adhesive effort between rail and driving wheel. Generally, the adhesive effort is defined by the function of both the weight of electric motor coach and the adhesive effort between rails and driving wheel. The characteristics of adhesive effort is strongly affected by the conditions between rails and driving wheel. When the adhesive effort decreases suddenly, the electric motor coach has slip phenomena. This paper proposes a re-adhesion control based on disturbance observer and sensor-less vector control. The numerical simulation and experimental results point out that the proposed readhesion control system has the desired driving wheel torque response for the tested bogie system of electric coach. Based on this estimated adhesive effort, the re-adhesion control is performed to obtain the maximum transfer of the tractive effort.