• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.166-172
• /
• 2001

A RF wideband receiver for INMARSAT-B satellite communications system was composed of low noise amplifier and high gain amplifier, The low noise amplifier used to the resistive decoupling circuit for input impedance matching and self-bias circuits for low noise. The high gain amplifier consists of matched amplifier type to improve receiver gain. The active bias circuit can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 60 dB in gain and less than 1.8:1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio which is input signal level -126.7 dB m at 1537.5 MHz is a 45.23 dB /Hz at a 1.02 kHz.

• Journal of the Korean Chemical Society
• /
• v.31 no.3
• /
• pp.207-214
• /
• 1987

Rates of solvblysis of benzyl chloride in ethanol-water mixtures have been measured at 30 and $40^{\circ}C$ under various pressures up 1.6 kbar. The plots of 1n k as a function of pressure are fitted to a second order function in p, and values of ${\Delta}V^{\neq}$and ${\Delta}{\beta}^{\neq}$ are obtained from the results. Also the values of various pseudo thermodynamic quantities were evaluated from the rate constants. The relationships of the 1n k to $Q_w$ or 1n $C_w$ indicate that the reaction proceeds through $S_N1$ mechanism. A comparison between the present and the previous results gives that the increasing order of ${\mid}{{\Delta}V_0}^{\neq}{\mid}$ and n-values are $p-Cl>p-H>p-CH_3$ and $p-CH_3>p-H.p-Cl$, respectively. From these results, it is believed substituent such as the $p-CH_3$group favors the $S_N1(1)$ character, while the p-Cl group leads to the $S_N1(2)$ character.

• Journal of the Korean Institute of Gas
• /
• v.20 no.2
• /
• pp.58-65
• /
• 2016

Hydraulic analysis of the natural gas transmission pipeline is to determine whether adequate flow can be sustained throughout the design life of pipeline under all expected flow conditions. Many factors have to be considered in the hydraulic design of long-distance pipelines, including the nature, volume, temperature and pressure of fluid to be transported, the length and elevation of pipeline and the environment of terrain traversed. This study reviewed the available gas operation data provided by pipeline construction project in the arctic area and discussed the gas properties such as viscosity and compressibility factor that influence gas flow through a pipeline. Pipeline inside diameter was calculated using several flow equations and pipeline wall thickness was calculated from Barlow's equation applying a safety factor and including the yield strength of the pipe material. The AGA flow equation was used to calculate the pressure drop due to friction, gas temperature and pipeline elevation along the pipeline. The hydraulic design in this study was compared with the report of Alaska Pipeline Project.

• Journal of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.431-435
• /
• 1989

The refractive index, refractive-index distribution, birefringence, and the attenuation of the plastic fiber prepared from the transparent PMMA prerod were measured in accordance with continuous heat drawing temperature($T_d$). The refractive indices were decreased with $T_d$ elevation but the refractive-index distribution from the center of fiber to periphery was higher at lower $T_d$. The steep decrease of gradient index was only at the periphery of higher $T_d$. Birefringence was observed only below $220^{\circ}C$ and ranged $5{\times}10^{-4}$ to $6{\times}10^{-4}$. No birefringence was observed above $220^{\circ}C$. An elevation of $T_d$ brought about a monotonous decrease in the attenuation of the fiber.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.8
• /
• pp.797-802
• /
• 2012

In this study, the potential performance enhancement in a dual heat pump system through series operation was investigated by a comparison between the performance for parallel and series operation for a heating supply temperature of $60^{\circ}C$. To compare the performance of each configuration fairly, the heat transfer surface area of the heat exchangers was fixed. The inlet temperatures and the flow rates of the heat source and the load were also fixed. In addition, the heat transfer and pressure drop characteristics of the working fluids were considered to achieve a more realistic comparison. The results show that the heating coefficient of performance (COP) of the series configuration is approximately 5% higher than that of the parallel configuration under the simulation conditions considered in the present study.

• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.122-132
• /
• 2001

Thermoplastic film infusion process was investigated by using a rubber tool, which intrinsically contains a thermally-expandable characteristic and effectively compensates for the pressure loss caused by thermoplastic polymer infusion. Increasing temperature up to the melting temperature of matrix, the polymer melt subsequently infused into the dry fabric, but the pressure was successfully sustained by the rubber tool. Even with the decreased resin volume, the rubber tool produced sufficiently high elastic force for continuous resin infusion. Combining D'Arcy's law with the compressibility of rubber tool and elastic fiber bed, a film infusion model was developed to predict the resin infusion rate and pressure change as a function of time. In addition, the film infusion process without the rubber tool was viewed and analyzed by a compression process of the elastic fiber bed and viscous resin melt. The compressibility of fiber bed was experimentally measured and the multiple-step resin infusion was well described by the developed model equations.

• Korean Journal of Food Science and Technology
• /
• v.19 no.2
• /
• pp.119-124
• /
• 1987

Combined cryoprotectants (C.C.) were formulated to depress freezing points of strawberry pulp and orange juice concentrate to ${-15}^{\circ}C$, and quality changes in fruit pulps during storage ai ${-15}^{\circ}C$ in the liquid state were investigated. C.C. suitable for strawberry pulp consisted of sucrose (2.5%, w/w), glucose (12.7%), fructose (12.7%), glycerol (1%), propylene glycol (1%) and ascorbic acid (0.1%), and that for orange juice concentrate containing 48% solids glucose (5%), fructose (5%), glycerol (4%) and citric acid (1%). When quality of fruit pulps was compared among control and those with C.C., quality of fruit pulps stored with added C.C. was at least as good as control, except treatment B which had significantly lower overall preference. Strawberry jam prepared from pulp stored for 4 monthes did not show any significant quality differences among control and treated samples. The results of this study indicated that fruit pulps could be stored with added C.C. in the liquid state at the frozen storage temperature, while maintaining qualities at least as good as the conventionally frozen stored products.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.183-183
• /
• 2000

Aigrain에 의해 Helicon이라는 이름이 명명된 이후, helicon은 저온의 금속과 같은 높은 전도도(conductivity)를 갖는 매질이나 강한 자기장이 걸려있는 plasma를 전파해 나가는 저주파 전자기장을 지칭해왔다. 이온화된 개스에서 이러한 전자기장은 전자 공명 주파수(electron cyclotron frequency)와 이온 공명 주파수(ion cyclotron frequency) 사이의 주파수로 전파하며 전리층 (ionosphere)을 통과하며 발생하는 가청 주파수 영역대의 음조가 강하하는 현상에 의해 low-frequency whistler라고도 불린다. Helicon wave plasma는 Boswell에 의해 처음 발생된 후, 높은 이온화율(~100%)로 인해 많은 연구가 이루어져 왔다. 1985년에 Chen은 helicon plasma의 높은 이온화율을 설명하기 위해 Landaudamping을 제시하였다. 이러한 설명은 1997년에 Shamrai에 의해 TG mode가 도입되기 전까지 직접적인 실험결과 없이 helicon plasma 발생의 mechanism으로 받아들여졌다. shamrai의 이론에 의하면 정전기파(electrostatic wave)는 plasma의 표면(surface)에서 강하게 감쇄되어 energy를 전달하게 된다. Cho는 radial density 분포가 외각보다 중심이 높을 경우 TG wave의 power 전달이 중심에서 일어날 수 있음을 계산하였다. Helicon plasma의 특성은 높은 이온화율에 의한 높은 밀도($\geq$1012cm3), 1-2 kW의 rf power에서 상대적으로 낮은 전자 온도( 4eV), $\omega$ci $\omega$LH<$\omega$ $\omega$ce $\omega$pe 영역대의 주파수, 자기장 50-1200 Gauss, 압력 1-10 mTorr로 특정지을 수 있다. 이러한 외부분수들의 조건에 k라 helicon plasma는 여러 종류의 mode로 존재한다. Degeling은 이러한 mode의 변화를 capacitive mode, inductive mode, 그리고 helicon mode(wave mode)의 세가지 부분으로 구분하였다. Helicon plasma가 갖는 높은 이온화율은 여러 가지 응용으로의 가능성을 가지고 있다. 그 예로 plasma processing, plasma wave에 의한 입자 가속, 그리고 가스 레이저 활성 매질 발생 등이 있다. 특히 plasma processing의 경우 helicon plasma는 높은 밀도, 비교적 낮은 자기장, remote operation 등이 가능하다는 점에서 현재 연구가 활발히 진행되고 있다. 상업용으로도 PMT와 Lucas Signatone Corp.에 서 helicon source가 제작되었다. 또한 높은 해리율을 이용하여 저유전 물질인 SiOF의 증착에서 적용되고 있다. 이 외에도 다수의 연구결과들이 발표되었다.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.440-445
• /
• 2008

The present study was investigated the effect of the driving condition on the performance of a louver fin and tube type heat exchanger under frosting condition. Heat transfer rate and pressure drop by frost were experimentally investigated. Effects of the wet blub temperature and the shape of a fin on heat transfer performances has been also investigated. The key parameters were fin type(louver and corrugate fin) and the wet blub temperature of air (0.5, 1.0, $1.5^{\circ}C$). The heat transfer performance of the louver fin and tube type heat exchanger was higher by 0.89% than the corrugate fin type. As the wet blub temperature of air were increased, the heat transfer rate, pressure drop and mass of frost of three test models(Type A, B, C) were increased. Especially, the maximum heat transfer rate and maximum pressure drop were shown for the louver fin and tube type heat exchanger. As a experimental result, the enhancement factor(EF) of louver fin and tube type heat exchanger was $0.2{\sim}0.4$ due to the high pressure drop.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.569-577
• /
• 1999

A wideband RF receiver for satellite mobile communications system was fabricated and evaluated of performance in low noise amplifier and high gain amplifier. The low noise amplifier used to the resistive decoupling and self-bias circuits. The low noise amplifier is fabricated with both the RF circuits and the self-bias circuits. Using a INA-03184, the high gain amplifier consists of matched amplifier type. The active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilized resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 55 dB in gain, 50.83 dBc in a spurious level and less than 1.8 : 1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio is a 43.15 dB/Hz at a 1 KHz from 1537.5 MHz.