• Tribology and Lubricants
• /
• v.34 no.4
• /
• pp.138-145
• /
• 2018

Elliptical bearings are widely used for large steam turbines owing to their excellent load carrying capacity and good dynamic stability. Power loss in bearings is an extremely important parameter, especially for high turbine capacities. Optimization of operation conditions and design variables such as bearing clearance and bearing length can reduce the power loss in elliptical bearings. Although changes in the oil supply method have served to increase the efficiency of the tilting pad journal bearing, it has not explicitly improved elliptical bearings. In this study, we verify the static characteristics of an elliptical bearing by changing the direction of oil supply. We evaluate the bearing power loss and bearing metal temperature, and compare the bearing performance and reliability in different test cases. The direction of oil supply is $90^{\circ}$ (9 o'clock) and $270^{\circ}$ (3 o'clock) when the rotor rotates in a counterclockwise direction. We use an elliptical bearing with an inner diameter and active length of 220.30 and 110.00 mm, respectively. Bearing power loss and bearing metal temperatures are measured and evaluated by rotor rotational speed, oil flow rate, and bearing load. The results reveal a 20 reduction in the power loss when the direction of oil supply is 90. Furthermore, the oil film on the upper part of the bearing has a high temperature when the direction of oil supply is $90^{\circ}$. In contrast, when the direction of oil supply is $270^{\circ}$, the oil film on the upper part of the bearing is relatively cold.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.28-33
• /
• 2020

In this study the possibility of hydrogen as a fuel in a small-sized two-stroke SI (Spark ignition) engine was investigated. For this purpose, experimental setup including an engine, a dynamometer, equipments for hydrogen and lubricant oil supply was prepared. And then preliminary experiments for the hydrogen-fueled engine combustion were conducted. In the case of hydrogen-fueled engines comparing to gasoline backfire occurs when the excess air ratio is lower than a specific value. This can cause engine power reduction and damage to the engine parts. The engine was controlled to operate at lean conditions to prevent backfire. Through the control of excess air ratio, the maximum engine brake power output of 3 kW was achieved in a 210 cc engine, while it was 6 kW in case of gasoline fuel.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.424-426
• /
• 2008

A parametric study was carried out to find the fuel lubrication performance of high speed small rolling element bearings. Both MIL-PRF-7808 turbine oil and JP-8 aircraft fuel were used as the lubricant to compare the operational characteristics. 17 mm inner diameter deep groove ball bearing and 20 mm cylindrical roller bearing were used. A high speed bearing test rig was developed and the testing was done with varying applied load, cooling air temperature, lubricant flow rate, and speed. Fuel caused more cage wear than oil for ball bearing with increasing axial load and rotational speed. The bearing temperature using fuel was lower than that using oil, and this seems to be the result of the high cooling capacity of fuel. According to various tests, the fuel lubrication is applicable for the lubrication on the main shaft bearings of expendable small gas turbines.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.332-332
• /
• 2012

분자선 에피탁시(molecular beam epitaxy)를 이용하여 GaAs 기판에 성장한 InAs 양자점(QDs: quantum dots)은 성장 온도, 압력, As/In의 공급비 등의 성장 조건에 따라 다른 변수(parameter)를 갖는다. 따라서 성장변수에 따라 양자점의 모양과 크기, 밀도가 달라져 균일한 양자점 형성에 어려움이 있어 많은 연구가 진행되고 있다. 예를 들면 In-interruption 법으로 성장한 양자점의 특성이 S-K mode (Stranski-Krastanov mode)로 성장한 양자점에 비해 광학적 특성이 향상되었다. 본 연구에서는 In pre-deposition (IPD) 법으로 성장한 InAs/GaAs 양자점의 광학적 특성을 PL(photoluminescence)와 TRPL (time-resolved PL)을 이용하여 분석하였다. InAs QDs 시료들은 In과 As 공급시간을 각각 1초와 19초 (QD1), 2초와 18초 (QD2), 3초와 17초 (QD3)로 조절하여 성장하였으며, In이 공급되는 시간 동안 As shutter를 차단하여 As 공급을 중단하였다. In과 As의 차단 없이 S-K mode로 성장한 시료를 기준시료로 사용하였다 (QD0). AFM (atomic force microscope) 측정결과, In 공급시간이 1초에서 2초로 증가할 때, 양자점의 밀도와 종횡비(aspect ratio)가 증가하였고, 양자점의 균일도가 증가하였다. 그러나 QD3 시료는 QD1 시료에 비해 밀도와 종횡비, 균일도가 감소하였다. 10 K에서 PL 피크는 In 공급 시간이 증가할 때, 970 nm에서 1020 nm로 적색편이 하였고 반치폭 (FWHM: full width at half maximum)은 75 meV에서 85 meV로 증가하였다. QD2 시료의 PL 피크 에너지가 가장 낮았고, 가장 강한 PL 세기를 보였다. IPD 시간이 증가함에 따라 PL 피크에서 측정한 PL 소멸은 점차 빨라졌다. IPD 기법으로 성장한 양자점의 빠른 PL 소멸은 양자점 밀도와 종횡비 향상에 의한 파동함수 중첩의 증가와 구속 에너지 증가에 의한 것으로 설명된다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.91-97
• /
• 2017

The KSLV-II launch complex system consists of mechanical ground support equipment(MGSE), fuel ground support equipment(FGSE), electrical ground support equipment(EGSE) and infrastructures. Compressed gas supply system, as a part of FGSE, is responsible for launch operations such as gas intake, storage, supply to launch vehicle and ground support equipments. This system consists of three primary elements such as gas storage part, control panel and controller. Automatic panels, as a part of control panel, are manufactured to operate remotely by controller. This study presents compressed gas supply system which is designed for KSLV-II and ground support equipment characteristics.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.95-103
• /
• 2019

Control systems of compressed gas supply facility are responsible for storing and supplying compressed gases required for launch complex qualification test and launch operation. Most of the facilities that make up the launch complex require compressed gas for their operation. Therefore, such control systems should be developed and verified earlier rather than the other systems that constitute the launch complex. Each verification for hardware and software is performed separately. In particular, software verification of control algorithms loaded on the controller takes a lot of time and man power during the development period of the control system. Thus, specific test procedures and methods should be prepared in advance for efficient development. This paper introduces the configuration of a compressed gas supply facility and its control system with the verification procedure and results of major algorithms.

• Journal of the Korean Institute of Gas
• /
• v.19 no.1
• /
• pp.12-17
• /
• 2015

The core of the CNG fueling station is the compressor and most of CNG compressors in Korea require lubrication. Lubrication oil of CNG compressor that can be transferred into the pressure regulators and the engines of fueling system can cause a negative effect on NGV(Nature Gas Vehicle) performance during refueling due to oil Carry-over. In order to avoid the problem, it is necessary to enhance the quality of the compressed natural gas by measuring quantitatively the amount of the transferred oil. In this research, a sampling device and sampling tube were developed, which can be used with a gravimetric method of detection to measure CNG oil Carry-over. In addition, CNG samples were taken at 6 pre-selected CNG fueling stations and analysed for their trace oil Carry-over. The measured total oil Carry-over ranged from 2.569 to 6.509 ppm. This test measurements were compared with those of previous studies to verify the results.

• Applied Chemistry for Engineering
• /
• v.20 no.4
• /
• pp.363-369
• /
• 2009

High oil price and biodiesel expansion lead the surplus of glycerol in the market. Glycerol has been used as a raw material itself at petroleum chemistry, paint, tobacco, household products and cosmetics in the conventional market. Recently, many research to find new applications of glycerol as a low-cost feedstock for functional derivatives have led to the introduction of a number of selective processes for converting glycerol into commercially value-added products. The recent studies on the development of new value-added glycerol derivatives will be reviewed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.9-18
• /
• 1995

The substitution of conventional fuel oil by alternative fuels is of immense interest due to liquid oil shortage and requirements of emission control standard. Among the alternative fuels, natural gas may be the most rational fuel, because of its widespread resource and clean est burning. Meanwhile, engine simulation is of great importance in engine development. Hence a zero-dimensional combustion model was developed for dual-fuel system. Natural gas was injected directly into the cylinder and small amount of distillate was used to provide the ignition kernel for natural gas burning. The intake air and exhaust gas flow was modeled by filling and emptying method. Although the single zone approach has an inherent limitation, the model showed promise as a predictive tool for engine performance. Its simulation was also made to see how the engine performance was influenced by the fuel injection timings and amount of each fuel.

• Tribology and Lubricants
• /
• v.24 no.3
• /
• pp.147-153
• /
• 2008

The effect of oil supply pressure on the performance of vapor cavitated short squeeze film dampers is examined. Vapor cavitation is characterized by film rupture occurring as a result of evaporating oils. The pressure of vapor cavity in the film is almost zero in absolute pressure and nearly constant. Pan's model about the shape of vapor cavity is utilized for studying the effect of vapor cavitation on the damping capability of a short squeeze film damper. As the level of oil supply pressure is increasing, vapor cavitation is suppressed so that the direct damping coefficient increases and the cross coupled damping coefficient decreases. Futhermore, the analysis of the unbalance responses of a rigid rotor supported on cavitated squeeze film dampers shows that a significant reduction in rotor amplitude and force transmissibility is possible by controlling the oil supply pressure into short squeeze film dampers.