• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1583-1588
• /
• 1999

Garlic pieces without peeling were subjected to hot air heating at $60{\sim}90^{\circ}C$ for 30 min. and microwave oven heating for 10 sec to reduce the strength of garlic flavor. Volatile compounds of the treated garlic were decreased, as the heating temperature was raised. Garlic heated at 70, 80 and $90^{\circ}C$ had 20%, 31% and 49% less volatile compounds, respectively, compared to those of the control. Microwave oven heating revealed a similar trend to those heated at $60{\sim}80^{\circ}C$. As the heating temperature was raised, glucose, fructose and fructooligosaccharide contents in the heated garlic were decreased. Pyruvic acid contents in garlic, a degradation product of alliin, was decreased as the heating temperature was raised, but contents of the other organic acids were not affected. Arginine, the main amino acid in garlic was decreased by the hot air heating, but was not affected by the microwave heating. Glutamic acid and tyrosine contents were decreased in all the treated garlic samples.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.570-576
• /
• 2018

In reinforced concrete structures, the joints of ordinary rebars are usually lap joints, which are bound by binding wires with rebars, and mechanical joints by couplers. In domestic design standards (concrete design code), welded lap joints are restricted for ordinary rebars, but overseas standards allow welded lap joints of ordinary rebars through pre-heating. This study investigated the domestic and international standards/criteria and evaluated the fracture strength by performing the tensile test on the lap welded joint of SD400 grade rebars, which is used the most in the construction sites. The weld length of the specimen for weld lap joints is based on the minimum weld length (8d) given in the KS standard (KS B ISO 17660-1). According to AWS D1.4, the preheating temperature was set to $150^{\circ}C$ for D19 and below, and $260^{\circ}C$ for D22 and above. In the test results, the tensile strength of rebars with welded lap joints exceeded the required strength (125% of the yield strength) according to the concrete design code. To analyze the effect of preheating, the tensile strength of the welded rebars after preheating was not significantly different from that of the welded rebars without preheating. The carbon equivalent content (Ceq) of the rebars used in the test was 0.45% or less. Under AWS D1.4, no preheating is required if the carbon equivalent is less than 0.45%. All specimens with a welded lap length of 8d failed by a bar fracture. The effect of preheating was confirmed to be insignificant due to the low carbon equivalent of the rebar.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.4
• /
• pp.15-25
• /
• 2022

In this study, the efficiency of treatment of moisture and organic matter in food waste was analyzed according to the air blast volume and preheating using the bio-drying method. Te mount of air blast volume and preheating were determined by the evaluation of temperature and CO2 during food waste treatment using the bio-drying method. As a results, the increase in the air blast volume increased the moisture removal efficiency and removal rate, but, lowered the temperature inside the bio-drying by the decease in microbial activity. In order to maintain the activity of microorganisms, it was estimated that it was necessary to inject an appropriate air blast rate according th the properties of the food waste. In this study, the injection of air blast volume at 15L/min was optimal. It was evaluated that the organic matter and water removal rates according to the presence or absence of air preheating, the organic matter removal rate and water removal rate increased by 3-5% when air preheating was not performed. Also, there was no internal aggregation caused by the generation of condensate inside the bio-drying. Therefore, for effective bio-drying of food waste, it is necessary to maintain an appropriate air blast volume to maintain microbial activity, and it is considered that injection through preheating of air is required.

• Journal of Korea Foundry Society
• /
• v.42 no.5
• /
• pp.273-281
• /
• 2022

In order to understand the solidification behavior and microstructural evolution of the Al-Cu-Si ternary eutectic alloy system, changes of the microstructure of the Al-Cu-Si ternary eutectic alloy with different cooling rates were investigated. When the mold preheating temperature is 500℃, primary Si and Al2Cu dendrites are observed, with (α-Al+Al2Cu) binary eutectic and needle-shaped Si subsequently observed. In addition, even when the mold preheating temperature is 300℃, primary Si and Al2Cu dendrites can be observed, and both (α-Al+Al2Cu+Si) areas observed and areas not observed earlier appear. When the mold preheating temperature is 150℃, bimodal structures of the binary eutectic (α-Al+Al2Cu) and ternary eutectic (α-Al+Al2Cu+Si) are observed. When the preheating temperature of the mold is changed to 500℃, 300℃, and 150℃, the greatest change is in the Si phase, and upon reaching the critical cooling rate, the ternary eutectic of (α-Al+Al2Cu+Si) forms. If the growth of the Si phase is suppressed upon the formation of (α-Al+Al2Cu+Si), the growth of both Al and Cu is also suppressed by a cooperative growth mechanism. As a result of analyzing the Al-27wt%Cu-5wt%Si ternary eutectic alloy with a different alloy design simulation programs, it was confirmed that different results arose depending on the program. A computer simulation of the alloy design is a useful tool to reduce the trial and error process in alloy design, but this effort must be accompanied by a task that increases reliability and allows a comparison to microstructural results derived through actual casting.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2001.05a
• /
• pp.45-52
• /
• 2001

The study on the heat exchanger with catalytic combustion was performed as the development of the catalytic combustion applications. This study tried to achieve the both goals-the mixture preheating and the heat transfer to working fluid simultaneously by using the steady state catalytic combustion. The combustion characteristics were investigated with the quantitative, qualitative experimental variants of the mixture. In addition, the temperature distribution of catalytic layer was investigated to investigate the correlation between the combustion characteristics and the heat balance of the catalytic layer. As a result, the steady state reaction within the appropriate range of temperature is the critical factor in catalytic applications. To get this, the sensible control of both the mixture flow and the heat balance of catalytic layer were required.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.551-559
• /
• 1998

장경비가 큰 탄화규소를 탄소와 규소간의 고온연소반응으로 제조하기 위하여 공정변수에 따른 연소거동과 미세조직의 변화를 조사하였다. 연소합성된 생성물은 주로 $\beta$-SiC이며 연소반응이 충분히 진행되지 못하였을 경우에는 미량의 잔류 반응물과 $\alpha$-SiC가 관찰되었다. 생성된 탄화규소의 평균입도는 약 5$\mu\textrm{m}$로 작았으며, $1300^{\circ}C$ 이상의 예열 조건에서 장경비가 30이상인 탄화규소를 합성할 수 있었다. 압분 강도가 69MPa인 분말의 성형체에서 평균 연소 온도와 평균 전파 속도는 각각 약 $1425^{\circ}C$와 2.1mm/sec 범위이며, 연소 온도는 흑연 분말을 사용하였을 경우가 탄소 섬유를 사용한 경우보다 약 $10^{\circ}C$ 높았다. 연소 반응을 임의로 중단시킨 시편의 계면을 EDX와 Auger 전자 현미경으로 분석한 결과 상호 확산층이 관찰되지 않았다. 이는 탄화규조의 연소합성이 용해-석출 모델에 의하여 진행됨을 시사한다. 예열 온도에 따른 연소 반응 중의 온도 분포를 유한 요소법으로 해석함으로써 $2500^{\circ}C$의 초기 연소 개시 온도에 대하여 예열 온도 $300^{\circ}C$에서는 연소파가 거의 전파할 수 없으며 예열 온도가 $1300^{\circ}C$에서는 시료 내부에 자체 전파가 가능한 $2000^{\circ}C$이상의 온도 구역이 존재함을 알았다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.168-171
• /
• 2008

항로표지용 LED 등명기는 완전방수형 구조이며, 발광형태도 섬광 특성을 가진다. LED 등명기의 색도 및 광도 측정에 있어 섬광형태로 측정하는 것은 그 한계가 있으며, 이에 부동광(연속광)으로 측정이 이루어진다. 이때 중요하게 취급되어져야 할 것이 예열시간이며, 적정한 예열시간 선정에 따라 Field와의 오차를 줄일 수 있다. 본 논문에서는 해상용 LED 등명기의 색도 측정 시에 고려해야 하는 예열 시간을 실험을 통하여 산정해 보았다.

• Korean Chemical Engineering Research
• /
• v.47 no.5
• /
• pp.572-579
• /
• 2009

This study is to investigate experimentally the flame structure and propagation mechanism in dust explosions and to provide the fundamental knowledge. Upward propagating laminar dust flames in a vertical duct of 1.8 m height and 0.15 m square cross-section are observed and flame front is visualized using by a high-speed video camera. Also, the thicknesses of preheated and reaction zone have been determined by a schlieren, electrostatic probe and thermocouple. The thickness of preheated zone in lycopodium dust flame is observed to be 4~13 mm, about several orders of magnitude higher than that of premixed gaseous flames. From the experimental results by a PIV(Particle Image Velocimetry) system, a certain residence time of the unburned particle in preheated zone is needed to generate combustible gas from the particle. The residence time will depend on preheated zone thickness, particle velocity and flame propagation velocity.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.191-197
• /
• 2014

To increase the heat transfer rate of the air pre-heating heat exchanger used for the condensing boiler, We investigated condensation heat transfer coefficients through plasma surface treatment. The hydrophilic surface showed about 10% increase in heat transfer rate than original plate. It shows that Shah correlation can be used to predict the condensation heat transfer coefficient on the original surface within 10% error range after the compatison between Shah correlation and the condensation heat transfer coefficients measured on the hydrophilic surface and original surface. Therefore, we have shown that Shah correlation is available when designing the air pre-heating heat exchanger using the original surface in this study.

• Explosives and Blasting
• /
• v.22 no.4
• /
• pp.17-22
• /
• 2004

Boryung sandstone and Yeosan marble were thermally cracked at predetermined temperatures ranging $200^{\circ}C$ to $600^{\circ}C$. Optical microscopy was utilized to observe thermally induced cracks and physical properties such as specific gravity, effective porosity k elastic wave velocity were measured. Optical observations show that all crystal boundaries of Yeosan marble heated to $600^{\circ}C$ open and new intracrystalline cracks seem to be occurred in all crystals, but developments of thermal cracks in Boryung sandstone heated to $600^{\circ}C$ are not pronounced. From $200^{\circ}C$ upwards, effective porosity and elastic wave velocity of Yeosan marble are sharpely increased, whereas effective porosity and elastic wave velocity of Boryung sandstone are weakly increased.