• Journal of Korea Foundry Society
• /
• v.42 no.5
• /
• pp.273-281
• /
• 2022

In order to understand the solidification behavior and microstructural evolution of the Al-Cu-Si ternary eutectic alloy system, changes of the microstructure of the Al-Cu-Si ternary eutectic alloy with different cooling rates were investigated. When the mold preheating temperature is 500℃, primary Si and Al2Cu dendrites are observed, with (α-Al+Al2Cu) binary eutectic and needle-shaped Si subsequently observed. In addition, even when the mold preheating temperature is 300℃, primary Si and Al2Cu dendrites can be observed, and both (α-Al+Al2Cu+Si) areas observed and areas not observed earlier appear. When the mold preheating temperature is 150℃, bimodal structures of the binary eutectic (α-Al+Al2Cu) and ternary eutectic (α-Al+Al2Cu+Si) are observed. When the preheating temperature of the mold is changed to 500℃, 300℃, and 150℃, the greatest change is in the Si phase, and upon reaching the critical cooling rate, the ternary eutectic of (α-Al+Al2Cu+Si) forms. If the growth of the Si phase is suppressed upon the formation of (α-Al+Al2Cu+Si), the growth of both Al and Cu is also suppressed by a cooperative growth mechanism. As a result of analyzing the Al-27wt%Cu-5wt%Si ternary eutectic alloy with a different alloy design simulation programs, it was confirmed that different results arose depending on the program. A computer simulation of the alloy design is a useful tool to reduce the trial and error process in alloy design, but this effort must be accompanied by a task that increases reliability and allows a comparison to microstructural results derived through actual casting.

• Proceedings of the KAIS Fall Conference
• /
• 2003.06a
• /
• pp.116-118
• /
• 2003

정밀주조에 사용되는 왁스형을 기존의 수작업과 금형을 이용하는 방법으로 제작하지 않고 SLS형 RP로 캐스트폼형을 만들고 여기에 왁스를 함침시켜 왁스형을 제작하는 공정을 제안하였다. 왁스형의 정밀도를 향상시키기 위해 캐스트폼형 예열시간, 왁스 함침시간, 왁스 함침 회수 등 중요한 공정변수를 변화시켜 가며 왁스형을 만들었다. 왁스형의 정밀도를 측정한 결과 예열시간이 적어도 30분 이상일 때 정밀도가 우수한 제품을 얻었으며, 왁수를 두 번이상 함침할 때 정밀도가 우수하였다. 왁스형의 표면거칠기는 예열시간이 늘어날수록 향상된 표면조도를 얻을 수 있었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.5
• /
• pp.419-425
• /
• 2016

A powder spreading phenomenon is one of disadvantageous characteristics of the powder bed fusion process using electron beams. The powder spreading phenomenon can be controlled using a pre-heating process of metallic powders. The aim of this paper was to investigate the preheating process of Stellite21 powder using electron beams. Powder spreading experiments were performed to examine the influence of process parameters on the spreading behaviors of Stellite21 powder. Powder heating experiments were carried to investigate the effects of the focusing current of the electron beam on the quality of the heated region. Using the results of the powder spreading and heating experiments, an appropriate combination of process parameters was obtained. The pre-heating experiment of Stellite21 was performed using the estimated combination of process parameters. The results of preheating experiments showed that the preheated Stelllite21 layer with desired characteristics can be created when the estimated combination of process parameters is applied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.9-9
• /
• 2009

본 연구에서는 MLCC 그린칩의 예열공정에서 나타난 수축 열변형 현상을 관찰하기 위해 각 구간별 온도를 달리하여 열-기계분석 Thermo-mechanical Anlaysis(TMA)으로 크립 특성 실험이 진행되었다. 수축 변형이 없는 안정화 구간을 확인하였으며, 분석결과를 바탕으로 제조기술에 적용가능한 간단한 수식을 이끌어내었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.12
• /
• pp.1017-1021
• /
• 2015

Induction heating has been applied to the preheating process in various industrial fields. It has been used as a simple device structure, limiting the heating zone through controlled variables, and free-welding positions. It would be helpful to weld thick plates with arc welding such as GMAW. The induction heating process is well suited to this process. In this study, in order to find suitable induction heating parameters, a simulation was conducted with multi physics S/W. Three kinds of material were heated by induction coils designed specially for thick plate. Consequently, steel and nimonic alloy were the most efficient materials for preheating by induction. It can be concluded that the induction heating process is a good method for preheating the thick plate.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.67-75
• /
• 1998

This study aimed at he experimental and finite element analytic investigation of the effect of preheating on he residual stress of weldment. In this study, an autogenous arc welding was used on type 304 stainless steel and MARC as F.E.M. common code was utilized in analysis The analyses include transient and moving heat source and thermal properties as function of temperature. During welding, the thermal cycles of four locations in the weldment were recorded to investigate of the behavior of thermal stress and residual stress. The experimental and analytic results had good coincidence and show that there are two factors influencing the formation of welding residual stress in preheat process. One is the elevation of welding equilibrium temperature and the other is the increase of amount of heat input. The former decrease welding residual stress and the latter increase welding residual stress. Therefore, the cumulative effects result in the welding residual stress not being improved significantly with preheating in 304 stainless steel.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.551-559
• /
• 1998

장경비가 큰 탄화규소를 탄소와 규소간의 고온연소반응으로 제조하기 위하여 공정변수에 따른 연소거동과 미세조직의 변화를 조사하였다. 연소합성된 생성물은 주로 $\beta$-SiC이며 연소반응이 충분히 진행되지 못하였을 경우에는 미량의 잔류 반응물과 $\alpha$-SiC가 관찰되었다. 생성된 탄화규소의 평균입도는 약 5$\mu\textrm{m}$로 작았으며, $1300^{\circ}C$ 이상의 예열 조건에서 장경비가 30이상인 탄화규소를 합성할 수 있었다. 압분 강도가 69MPa인 분말의 성형체에서 평균 연소 온도와 평균 전파 속도는 각각 약 $1425^{\circ}C$와 2.1mm/sec 범위이며, 연소 온도는 흑연 분말을 사용하였을 경우가 탄소 섬유를 사용한 경우보다 약 $10^{\circ}C$ 높았다. 연소 반응을 임의로 중단시킨 시편의 계면을 EDX와 Auger 전자 현미경으로 분석한 결과 상호 확산층이 관찰되지 않았다. 이는 탄화규조의 연소합성이 용해-석출 모델에 의하여 진행됨을 시사한다. 예열 온도에 따른 연소 반응 중의 온도 분포를 유한 요소법으로 해석함으로써 $2500^{\circ}C$의 초기 연소 개시 온도에 대하여 예열 온도 $300^{\circ}C$에서는 연소파가 거의 전파할 수 없으며 예열 온도가 $1300^{\circ}C$에서는 시료 내부에 자체 전파가 가능한 $2000^{\circ}C$이상의 온도 구역이 존재함을 알았다.

• Resources Recycling
• /
• v.4 no.4
• /
• pp.37-58
• /
• 1995

Whole tues were put uto cement kiln inlet where the tempmalures or gas and cemcnt-raw-materials were 1050 and 800- 850.C. respcclrvely. Tl~ck iln consisls of \ulcorner-stage suspension preheatel- and air quenching coolers The amount of wusle tlrcs added in lhc normal encrgy in lhc ce~ncnlk iln was 3, 5, 7% by volume Welght and steel contents of tiles. ulti~~iaalcn d elemental analysis, ash contents. ash hsion temperature. etc, wete detcnutned to inveshgate thc prnpcrlics a1 tires and ilreir ashes. Flucluat~ons of cement kiln placess, cement quality and an pollulton were invesligalerl during lhc burning tins. When the Ieeding ralio ol wasle lires to normal cncrgy was 50'0, there was nn wlde d~ffereilces m the cemmt quctlity and air pollutcon between operation with tiles and withoul tires. Tl~ch cal iccovcry was uhout 50% w~th5 % add~tionI n the nonndl energy. There was a little lxt fluctuation of cement quultty ncld an pollution at olher feeding ralios.

• Food Engineering Progress
• /
• v.14 no.3
• /
• pp.193-201
• /
• 2010

The aim of this study was to analyse the quality of Yukwa puffed by using a vacuum puffing machine and compare to deep-fried Yukwa. The effect of vacuum puffing condition including heating temperature(100-${160^{\circ}C}$), preheating time(0-8 min) and vacuum puffing time(5-20 min) on physical and microstructure characteristics of the Yukwa was investigated. Vacuum puffed Yukwa at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 10 min puffing time had highest value in volumetric expansion ratio(10.04) and lowest value in bulk density(0.15 g/$cm^{3}$). The breaking strength showed the lowest value of 140 g/$cm^{3}$ in vacuum puffing Yukwa at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 15 min puffing time. The Yukwa puffed with the vacuum puffing machine at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 15 min puffing time had the higher value of bulk density and the lower value of volumetric expansion ratio than those of deep-fried Yukwa. Increasing preheating time and vacuum puffing time caused an increase in white and an decrease in yellowness. The vacuum-puffed Yukwa exhibited smaller and uniform cell structure, while deep-fried Yukwa exhibited apparently in larger pores inside and smaller pores near the surface layer. The optimum condition of vacuum puffing machine for the production of vacuum-puffing Yukwa was ${120^{\circ}C}$ heating temperature, 4 min preheating time and 5 min puffing time.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1993.11a
• /
• pp.13-21
• /
• 1993

석탄가스화 복합발전 플랜트의 부속공정인 중기터빈 시스템에 대한 공정 전산해석을 상용 공정해석 소프트웨어인 ASPEN 코드를 이용하여 수행하였다. 폐열회수보일러에서 생성되는 고압증기 조건을 2400psig로 채택하였으며, 폐열회수보일러의 열교환기 배열 및 생성증기의 조건에 따른 증기터빈 시스템의 성능변화를 고찰하였다. 페열회수보일러에서의 열교환기 배열, 생성중기 조건 및 공급수 예열 방법에 따라 증기터빈 시스템의 성능이 변화하게 되므로 이의 정확한 이해를 통하여 증기터빈 시스템의 최적화를 도모할 수 있다.