• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.12 s.148
• /
• pp.1619-1626
• /
• 2005

The durability of a stretch fabric is mainly related to the change in the dimension and mechanical properties of elastomeric fibers during wearing and washing. In this study, we examined the effects of washing temperature, presoaking time and the number of washing cycles on the change in length, tenacity, elongation at break, and permanent elongation after six repeated cycles of $100\%$ extension and relaxation of spandex yams with varying fineness and with a different rate of extension during heat-set. The spandex yarns continued to shrink as the wash temperature and the number of wash cycles increased. In addition, the finer spandex yams decreased in length more than the thicker yams. The increase in temperature and presoaking time tended to cause a slight decrease in the tenacity and elongation at break of the spandex yarns. Permanent elongation of the spandex yams also increased as the temperature, presoaking time and the number of washing cycles increased. Moreover, an extended presoaking time followed by washing at $40\%$ like repeated washing cycles showed the great increase in the permanent elongation of spandex yams. The thinner spandex yin had a better elasticity than the thicker one, since the former had a lower permanent elongation percentage than the latter. Based on the DSC thermograms, the melting points of the spandex yarns after washing were almost the same as those of the spandex yarns before washing.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.2
• /
• pp.15-21
• /
• 2013

The analysis of long-term performance of pavement sections under wheel loads is normally conducted in two separated steps. First the resilient behavior of the pavement is calculated assuming the pavement is a layered or discrete elastic medium, and then the permanent deformation is evaluated based on empirical permanent displacement equations. Material properties required in both steps can be obtained from cyclic triaxial tests, in other words, resilient and permanent deformation tests. While this analytical approach is simple and convenient, it does not consider the modulus degradation caused by cyclic loads, and some types of reinforcements such as geosynthetic cannot be modeled in this type of analysis. A model for degraded secant modulus is proposed and suggested to be used for the analysis of permanent behavior of unpaved roadway sections. The parameter for suggested model can be obtained from cyclic triaxial tests, regular practice in pavement engineering. Examples to estimate the model parameters are presented based on both laboratory permanent deformation test and large-scale plate load test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.284-289
• /
• 2016

In recent years, the earthquake sequence in Christchurch, New Zealand (NZ) was unprecedented in terms of repeated earthquake shocks with substantial levels of ground motion affecting modern infrastructure, and in particular, broad and precise reports for liquefaction-induced permanent ground deformation (PGD) and repairs of wastewater (WW) pipelines were collected. In this study, a geographical information system (GIS) and linear regression analysis were performed using data for the length and repair points of earthenware (EW) and concrete (CONC) wastewater pipelines acquired after the MW 6.2 February 22, 2011 earthquake. The repair rates (repairs/km) for the EW and CONC wastewater pipelines were evaluated inside the areas of PGD, and both angular distortion of ground and lateral ground strain were calculated from the high resolution LiDAR data acquired before and after the seismic event. The research results showed that both pipelines have similar trends of damage but the CONC wastewater pipeline with higher stiffness showed less damage. The results of linear regression analyses can be used to predict the repair rates for EW and CONC wastewater pipelines inside the areas of PGD induced by future earthquakes.

• Elastomers and Composites
• /
• v.44 no.1
• /
• pp.41-46
• /
• 2009

The effects of temperature and curing systems on the compression set of natural rubber (NR) at constant load were investigated. NR was compounded with various amounts of sulfur and DCP in order to obtain various crosslink densities and curing systems. Compression sets at constant load were compared with those at constant strain. Compression set at constant load was more affected by changes in crosslink density than compression set at constant strain, due to the differences of exerted strain energy density. Compression set of sulfur cured NR under constant load was increased with increasing load and temperature, but the compression set of DCP cured NR was not changed by increasing load and temperature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4201-4207
• /
• 2015

In this study, the performance of underground water pipeline system affected by earthquakes is examined by using data acquired after MW 6.2 February 22, 2011 earthquake in Christchurch, NZ. Water pipeline repair rates, expressed as repairs/km, for different types of pipe are evaluated inside the areas of which liquefaction induced by permanent ground deformation was observed and assessed relative to differential settlement and lateral ground strain, calculated from high resolution LiDAR data acquired before and after each seismic event. The earthquake performance of underground water pipeline systems associated with permanent ground deformation is summarized in this paper. The results show that highly ductile polyethylene water pipelines has a high earthquake performance.

• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.149-163
• /
• 2021

Damage characteristics of granite, marble and sandstone whose properties were different were investigated by uniaxial compression test and cyclic loading-unloading test. Strength, elastic constants and damage threshold stresses were measured by uniaxial compression test and were compared with those measured by cyclic loading-unloading test. Average rock strengths measured by cyclic loading-unloading test were either lower than or similar with those measured by uniaxial compression test. Rocks with high strength and low porosity were more sensitive to fatigue than that with low strength and high porosity. Although permanent strains caused by cyclic loading-unloading were different according to rock types, they could be good indicators representing damage characteristics of rock. Damage threshold stress of granite and marble might be measured from stress-permanent strain curves. Acoustic emissions were measured during both tests and felicity ratios which represented damage characteristics of rocks were calculated. Felicity ratio of sandstone which was weak in strength and highly porous could not be calculated because of very few measurements of acoustic emissions. On the other hand, damage threshold could be predicted from felicity ratios of granite and marble which were brittle and low in porosity. The deformation behaviors and damage characteristics of rock mass could be investigated if additional tests for various rock types were performed.

• Elastomers and Composites
• /
• v.40 no.4
• /
• pp.258-265
• /
• 2005

To study the compressive stress, recovery force and permanent strain of foams for footwear midsole, polyurethane(PU), phylon(PH) and injection phylon(IP) foams were repetitively compressed with constant compressive stress. Maximum compressive stress of PU did not decrease with repetitive compression on the constant compressive stress, but that of IP largely decreased. Engineering strain of foams were formed by repetitively compressing the three types of foam. The engineering strain of PU was smaller than that of IP and PH. Compressive stress and recovery force of IP and PH at certain strain were decreased with repetitive compression, but that of PU was not noticeably changed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.490-496
• /
• 2012

The main object of this research is to minimize the shock effects which frequently result in fatal damage in offshore wind turbine on impact of barge. The collision between offshore wind turbine and barge is generally a complex problem and it is often impractical to perform rigorous finite element analyses to include all effects and sequences during the collision. On applying the impact force of a barge to the offshore wind turbine, the maximum acceleration, internal energy, and plastic strain are calculated for each load case using the finite element method. A parametric study is conducted with the experimental data in terms of the velocity of barge, thickness of the offshore wind turbine, and thickness and Mooney-Rivlin coefficient of the rubber fender. Through the analysis proposed in this study, it is possible to determine the proper size and material properties of the rubber fender and the optimal moving conditions of barge.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.79-89
• /
• 2008

The pavement performance model is the most important factor to determine the pavement life in the mechanistic-empirical pavement design guide (MEPDG). As part of Korean Pavement Research Program (KPRP), the Korean Pavement Design Guide (KPDG) is currently being developed based on mechanistic-empirical principle. In this paper, the rutting prediction model of asphalt mixtures, one of the pavement performance model, has been developed using triaxial repeated loading testing data. This test was conducted on various types of asphalt mixtures for investigating the rutting characteristics by varying with the temperature and air void. The calibration process was made for the coefficients of rutting prediction model using the accelerated pavement testing data. The accuracy of prediction model can be increased when by considering the effect of individual rutting properties of materials rather than shear stresses with depths.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1D
• /
• pp.45-55
• /
• 2008

The objective of this research was to develop a VEPCD (ViscoElastoPlastic Continuum Damage) Model which is used to predict the behavior of asphalt concrete under various loading and temperature conditions. This paper presents the VEPCD model formulated in a tension mode and its validation using four hot mix asphalt (HMA) mixtures: dense-graded HMA, SBS, CR-TB, and Terpolymer. Modelling approaches consist of two components: the ViscoElastic Continuum Damage (VECD) mechanics and the ViscoPlastic (VP) theory. The VECD model was to describe the time-dependent behavior of HMA with growing damage. The irrecoverable (whether time-dependent or independent) strain has been described by the VP model. Based on the strain decomposition principle, these two models are integrated to form the VEPCD model. For validating the VEPCD model, two types of laboratory tests were performed: 1) a constant crosshead strain rate tension test, 2) a fatigue test with randomly selected load levels and frequencies.