• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.42-47
• /
• 2001

The heat (mass) transfer characteristics on the blade surface of a first-stage turbine rotor cascade for power generation has been investigated by employing the naphthalene sublimation technique. A four-axis profile measurement system is successfully developed for the measurements of the local heat (mass) transfer coefficient on the curved blade surface. The experiment is carried out at the free-stream Reynolds number and turbulence intensity of $2.09\times10^5$ and 1.2%. The results on the blade surfaces show that the local heat (mass) transfer on the suction surface is strongly influenced by the endwall vortices, but that on the pressure surface shows a nearly two-dimensional nature. The pressure surface has a more uniform distribution of heat load than the suction one.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1171-1178
• /
• 1992

An experiment was performed to describe the heat and mass transfer occurring between hot waste gas and cold water through direct contact in a direct contact heat exchanger. This model was then used to obtain an equation of overall heat transfer coefficent based on heat exchanger volume. The diffusion heat transfer rate is 2-3 times larger than the convection heat transfer rate as results of condensation of the water vapor contained in the waste gas. The boiler efficiency increases over 10%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.56-63
• /
• 1998

The present study investigated local heat transfer characteristics around a film cooling hole with variations of free stream turbulence intensity The film cooling jet is injected through a single hole inclined at $30^{\cire}$ to the surface and laterally at $45^{\cire}$ for the blowing rates of 0.5, 1.0 and 2.0. Turbulence generating grids are used at upstream of the film cooling hole to change the turbulence intensity of free stream. Free stream turbulence intensity without grids is 0.5%. Two different turbulence generating grid is installed at different at locations upstream of the film cooling hole so that turbulence intensity of free stream varies from 3% to 10%. The naphthalene sublimation technique has been employed to determine local heat/ mass transfer coefficients. With low free stream turbulence intensity, heat/mass transfer augmented area by coolant or free stream is distinguished evidently. However, when free stream turbulence intensity is high, heat transfer is enhanced in all region and heat transfer enhanced regions are not clearly divided due to vigorous mixing of coolant and free stream. The peak values of heat/mass coefficients are decreased and the distributions of heat/mass transfer coefficients are more uniform with high turbulence intensity. The effect of turbulence intensity on heat transfer characteristics is more evident as blowing rate is higher.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.217-223
• /
• 1996

혼합증기(수증기/공기)의 막응축 열전달 계수를 수직한 벽면에서 측정하고 상관식을 개발하였다. 열전달 상관식은 액막측과 증기측으로 구분하여 만들었고, 액막측 전열계수의 상관식은 액막의 Reynolds수와 Prandtl수의 함수로 나타냈으며, 증기측 전열계수의 상관식은 증기의 Reynolds수, Prandtl수, Schmidt수 및 공기의 질량분율, 액막 Reynolds수의 함수로 제안하였다. 응축 액막의 두께와 확산층의 순간온도 측정결과로부터 액막의 파형 계면이 확산층에서의 열 및 물질전달에 큰 영향을 끼치고 있음을 확인하였고, 증기측 전열계수의 상관식에 포함된 액막 Reynolds수가 파형 계면의 영향을 반영하고 있다.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.4
• /
• pp.36-42
• /
• 2010

본 논문은 태양열이용 냉난방시스템 중에서 실제로 액체흡수제를 재생하는 재생탑 내의 충진층에 있어서의 열 및 물질전달의 실험치와 이론적 해석에 의한 결과치와의 비교를 나타내고 있다.특히 물질전달의 극대화를 위하여 충진층 내에서 공기와 흡수제의 접촉면적을 크게 할 필요가 있는데,이를 위해서 본 실험에서는 직경이 3cm인 플라스틱제 충진재를 사용하였으며, 흡수제로는 저농도의 염화리튬 수용액이 사용 되었다. 충진층 내에서의 최적 높이를 예측하기 위하여 해석의 모델인 실험장치를 직접 제작하여 실험을 수행하였고, 이론 해석에 있어서 체적 열전달을 고려한 정상상태를 모델화하여 해석하였다. 이 결과, 충진층 내에서 실험치와 이론적인 계산치가 잘 일치함을 알 수 있었으며, 충진층의 높이가 2m 이상인 경우에는 높이에 따른 재생량의 차이가 없어서 없음을 알 수 있었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.2
• /
• pp.202-209
• /
• 2005

This study concerns the performance of boiling heat transfer in inclined thermosyphons with internal grooves. A study was carried out with the performance of the heat transfer of the inclined thermosyphon having 60 internal grooves in which boiling and condensation occur. A plain thermosyphon having the same inner and outer diameter as the grooved thermosyphon is also tested for comparison. Distilled water, methanol and ethanol have been used as the working fluid. The inclination angle, three working fluids, heat flux and the boiling heat transfer coefficient at the evaporator zone are estimated from the experimental results. The experimental results have been assessed and compared with existing correlations. Imura's and Kusuda's correlation for boiling showed in good agreement with experimental results within ${\pm}20%$ in plain thermosyphon. The high heat transfer coefficient was found between $25^{\circ}$ and $30^{\circ}$ of inclination angle for water and between $20^{\circ}$ and $25^{\circ}$ for methanol and ethanol. The relatively high rates of heat transfer have been achieved in the thermosyphon with internal micro grooves.

• Journal of Energy Engineering
• /
• v.9 no.3
• /
• pp.184-191
• /
• 2000

본 연구에서는 국내 10MW급 기력발전소의 소형 터빈 로터에 대한 응력 해석을 실시하였다. 터빈 로터의 기하학적 형상, 증기의 온도 및 압력 등의 기동조건 변화, 로터 재료의 온도에 따른 물성값 등을 고려하여 대류 열 전달계수를 계산하는 사용자 부프로그램을 구성하였으며, 이를 바탕으로 열해석을 실시하여 로터의 온도 분포를 결정하였다. 이 온도분포 조건에서 시간 경과에 따른 열응력 해석을 실시하여 로터의 응력 분포를 결정하였으며 그 결과 취약부위에서의 응력변동 범위 및 가동중 정상상태 응력수준을 결정하였다. 이 취약부위의 응력값과 운전이력을 이용하여 크리프 수명과 피로수명을 계산하고 로터의 잔여수명을 결정하는 방법을 논의하였다.

• Fire Science and Engineering
• /
• v.27 no.6
• /
• pp.15-20
• /
• 2013

The convective heat transfer coefficient, emissivity, and flame heat flux on the surface of Duglas fir are estimated by using repulsive particle swarm optimization. The surface temperature, mass loss rate, and ignition time are measured for various incident heat fluxes from a cone heater of the cone calorimeter. The calculated surface temperatures obtained by using the optimized convective heat transfer coefficient, emissivity and flame heat flux on the surface in this study match well with those obtained from the test. The maximum error between the predicted and measured surface temperatures for the three different external heat fluxes is within 2% showing reasonable agreements. The methodology proposed in this study can be used to obtain various values related to heat transfer on a flaming surface that are difficult to measure in experiments.

• Journal of Bio-Environment Control
• /
• v.29 no.1
• /
• pp.9-19
• /
• 2020

Convective heat transfer is the main component of greenhouse energy loss because the energy loss by this mechanism is greater than those of the other two components (radiative and conductive). Previous studies have examined the convective heat transfer coefficients under natural conditions, but they are not applicable to symmetric thermal screens with zero porosity, and such screens are largely produced and used in Korea. However, the properties of these materials have not been reported in the literature, which causes selectivity issues for users. Therefore, in this study, three screens having similar color and zero porosity were selected, and a mathematical procedure based on radiation balance equations was developed to determine their convective heat transfer coefficients. To conduct the experiment, a hollow wooden structure was built and the thermal screen was tacked over this frame; the theoretical model was applied underneath and over the screen. Input parameters included three components: 1) solar and thermal fluxes; 2) temperature of the screen, black cloth, and ambient air; and 3) wind velocity. The convective heat transfer coefficients were determined as functions of the air-screen temperature difference under open-air environmental conditions. It was observed from the outcomes that the heat transfer coefficients decreased with the increase of the air-screen temperature difference provided that the wind velocity was nearly zero.

• 전기의세계
• /
• v.28 no.12
• /
• pp.27-32
• /
• 1979

13명의 환자에 있어서 새로운 비관혈적 방법에 의한 심박출량을 계산하고, 열희석에 의한 방법으로 측정한 심박출량과 비교하였다. 본 논문에서 사용한 비관혈적 펄스 전달 방법은 대동맥 모델에서의 최적 매개변수 방법을 사용하였다. 모델의 최적 매개변수는 맥압의 첫번째 고주파 전달함수에서 측정치와 계산치의 차이를 최소화하는 조건에 의하여 계산하였다. 전달함수의 2개의 펄스는 각각 경동맥동과 대퇴동맥에서 Piezo-resistive Pulse Microphone을 사용하여 측정하였고, 대동맥의 직경은 초음파 방법을 사용하여 측정하였다. 13명의 환자에게서 16가지 측정을 해서 열희석과 비관혈적 방법은 0.89의 상관계수를 보여주었다.