• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.16 no.2
• /
• pp.1-6
• /
• 2020

This work experimentally explored the influence of nano-fouling on CHF, flow boiling heat transfer coefficient, contact angle, and surface roughness. In this study, the flow velocity conditions are established at 0.5, 1.0, and 1.5 m/s. Also, the nanoparticles of oxidized MWCNT were deposited on a heat transfer surface for 0, 120, 180, and 240 sec. As the results, it was found that CHF and superheated temperature were increased in case of nano fouling on the heat transfer surface in oxidized MWCNT fluid. Also, the contact angle and surface roughness decreased when flow velocity and nano coating increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.961-967
• /
• 2004

An inclined jet impinging on a pin fin heat sink is proposed and investigated experimentally. To investigate the flow pattern, flow visualization using fluorescence and velocity measurement using particle image velocimetry(PIV) are conducted with water. The jet impinges over a wide span of the heat sink with a large recirculation in the upper free space and occasionally with another smaller one in the upstream corner. Further, thermal experimentation is conducted using air to obtain temperature profiles using a thermocouple rake in the air and using thermal image on the heat sink back plate, with impinging angles of 35, 45 and 55 degrees. The Reynolds number range based on the nozzle slot is varied from 1507 to 6405. The results show that impinging angle of 55 degree shows the largest heat transfer capability. The results of thermal experiment are compared and discussed with those of flow visualization.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.1
• /
• pp.62-66
• /
• 2011

In this study, the thermal performance of disk can be compared with disk and disk with holes through numerical analysis. The capacity of thermal emission on general disk becomes more than on disk with holes at the distribution of temperature at first and the magnitude of equivalent stress on general disk becomes less than on disk with holes at the distribution of stress. The capacity of thermal emission or the magnitude of thermal deformation on disk with holes becomes less than that on general disk 30 minutes later. The disk with holes is worn less and more durable than general disk. The performance of cooling and braking force at disk and pad can be improved by installing the disk with holes.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.3
• /
• pp.193-200
• /
• 2003

In the production of internal combustion engines, there has been a move towards the development of high performance engines with improved fuel efficiency, lighter weight and smaller sizes. These trends help to answer problems in engines related to thermal load and abnormal combustion. In order to investigate these problems, a thin film-type probe for instantaneously measuring temperatures has been suggested. A method for manufacturing such a probe was established in this study. The instantaneous surface temperature of a constant volume combustion chamber was measured by this probe and the heat flux was obtained through Fourier analysis. In order to thoroughly understand the characteristics of combustion, the authors measured the wall temperature of the combustion chamber and computed heat flux through a cylinder wall while varying the protrusion height of the probe. For achieving the above goals, a instantaneous temperature probe was developed, thereby making possible the analysis of the instantaneous temperature of wall surface and the detection of unsteady heat flux in the constant volume combustion chamber.

• Journal of Energy Engineering
• /
• v.9 no.4
• /
• pp.319-327
• /
• 2000

산업분야의 여러공정에서 배출되는 휘발성 유기화합물은 1차적인 작업자에 대한 유해성뿐만이 아니라 대기중에 배출시의 제 2차 오염물질의 생성 때문에 최근 들어 이러한 물질의 처리에 큰 관심이 집중되고 있다. 본 연구에서는 휘발성 유기화합물로서 프로판을 사용하여 이러한 초 희박 혼합기의 제거를 위해 재생열산화법이 제안되었다. 실험장치에는 중앙에 연소실과 전기적 열량공급장치를 장착하였다. 초 희박 혼합기의 연소실에서의 산화과정과 열사화 장치의 폐열회수 특성을 연구하기 위하여 혼합기의 농도, 유속 및 연소실 최대온도와 같은 다양한 작동조건을 고려하였다. 그 결과. 재생열산화장치가 초 희박 혼합기의 산화에 적절하게 사용될 수 있음을 알았으며 최대 96%의 제거효율 얻을 수 있었다. 산화과정중에 발생하여 배출되는 CO는 운전조건을 변화시킴으로써 그 농도를 낮출 수 있었으며 열적 NOx는 배출되지 않았다. 페열회수효율은 전 운전영역에서 높게 나타났으며 그 값이 최대 98%에 이르렀다.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.2
• /
• pp.35-40
• /
• 1992

A recently developed new technique for measuring the fraction of wetted area has applied to pool boiling of water. The basis of the new applied technique of ultrasonic makes use of the reflection of ultrasonic from the vapour surface to measure the fraction of wetted area values. The results are the measured fraction of wetted area values in nucleate and transition boiling and the pool boiling curve for water under steady state conditions. The measurement of this paper shows a fraction of wetted areaf around 0.98 at the critical heat flux for water.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.9
• /
• pp.764-771
• /
• 2007

The objective of the present work is to evaluate the evaporation heat flux of deposited droplet on the hot surface by using of inverse heat transfer technique. On the basis of measured temperature, a integral form solution is determined for the transient temperatures beyond the two positions by using Green's function technique. This method first approximates the temperature data with a half polynomial series of time. we compared this result with constant radius model in single phase regime, nucleate boiling regime, film boiling regime respectively. this paper performed the experiments as following conditions: (a)the surface temperature is within the range between $80^{\circ}C\;and\;160^{\circ}C$ in the conduction, (b) droplet diameter are 2.4 and 3.0mm. (c) surface roughness is $0.18{\mu}m$.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.12 s.189
• /
• pp.64-71
• /
• 2006

In this study, to design aluminum scrap recycling equipment, fluid flow and thermal analysis considering electromagnetic phenomenon were carried out by using ANSYS program. The magnetic flux generated by electromagnetic pump has influence on fluid velocity of Al liquid metal with molten metal motion and thermal generation. To investigate the effect of the number of phase on fluid flow and thermal generation, electromagnetic force and magnetic flux were obtained by computer simulation. In addition, the results obtained by fluid flow and thermal analysis, recycling equipment of aluminum scrap with the cooling technology of electromagnetic coil, the most suitable phase and current were proposed.

• Proceedings of KOSOMES biannual meeting
• /
• 2003.11a
• /
• pp.187-190
• /
• 2003

한반도 서남부해역은 하계 양자강의 방류에 의해 저염분 현상이 발생한다. 양자강 방류량은 해마다 일정하지 않으며, 과거 시계열자료에 의하면 최대값이 최소값보다 2배 이상이 됨을 알 수 있다. 다라서 양자강의 방류량을 달리하여 저염분포를 수치모델로 연구하고자 하였다. 수치모델은 POM(Princeton Ocean Model)을 사용하였다. POM은 연직적으로 $\sigma$-좌표계를 사용하는 3차원 순환모델이다. 모델 수행 후 연구해역내 대륙사면부에서 유속이 강하게 나타남을 알 수 있다. 또한 제주도 서쪽을 통해 북상하여 황해중앙부로 들어가는 흐름이 있으며, 대륙연안을 따라 남하하는 흐름이 있음을 알 수 있다 양자강 방류량을 부여한 수행한 모델의 결과를 보면 양자강 방류량이 많을수록 저염분역이 제주도에 가깝게 나타남을 랄 수 있다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.167-170
• /
• 2009

Fast cook-off test with rocket motors was performed and characteristics of the results were analyzed. The material of the motor case was carbon epoxy composite. The motor was loaded with HTPE propellants to improve the insensitive munitions characteristics. In the tests, sound pressure and heat flux sensors were used to determine the category of response according to the standard. The reaction response of all of the HTPE motors tested by fast cook-off was judged as Type V burning.