• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.243-260
• /
• 2018

A literature review on the effects of high temperature and radiation on radiation shielding concrete in Spent Fuel Dry Storage is presented in this study with a focus on concrete degradation. The general threshold is $95^{\circ}C$ for preventing long-term degradation from high temperature, and it is suggested that the temperature gradient should be less than $60^{\circ}C$ to avoid crack generation in concrete structures. The amount of damage depends on the characteristics of the concrete mixture, and increases with the temperature and exposure time. The tensile strength of concrete is more susceptible than the compressive strength to degradation due to high temperature. Nuclear heating from radiation can be neglected under an incident energy flux density of $10^{10}MeV{\cdot}cm^{-2}{\cdot}s^{-1}$. Neutron radiation of >$10^{19}n{\cdot}cm^{-2}$ or an integrated dose of gamma radiation exceeding $10^{10}$ rads can cause a reduction in the compressive and tensile strengths and the elastic moduli. When concrete is highly irradiated, changes in the mechanical properties are primarily caused by variation in water content resulting from high temperature, volume expansion, and crack generation. It is necessary to fully utilize previous research for effective technology development and licensing of a Korean dry storage system. This study can serve as important baseline data for developing domestic technology with regard to concrete casks of an SF (Spent Fuel) dry storage system.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.55-60
• /
• 2020

The PERC photovoltaic (PV) modules installed in PV power plant are still reports potential-induced degradation (PID) degradation due to high voltage potential differences. This is because Na+ ions in the cover glass of PV modules go through the encapsulant (EVA) and transferred to the surface of solar cells. As positive charges are accumulated at the ARC (SiOx/SiNx) interface where many defects are distributed, shunt-resistance (Rsh) is reduced. As a result, the leakage current is increased, and decrease in solar cell's power output. In this study, to prevent of this phenomenon, a Moth-eye nanostructure was deposited on the rear surface of an optical film using Nano-Imprint Lithography method, and a solar mini-module was constructed by inserting it between the cover glass and the EVA. To analyze the PID phenomenon, a cell-level PID acceleration test based on IEC 62804-1 standard was conducted. Also analyzed power output (Pmax), efficiency, and shunt resistance through Light I-V and Dark I-V. As a result, conventional solar cells were decreased by 6.3% from the initial efficiency of 19.76%, but the improved solar cells with the Moth-eye nanostructured optical film only decreased 0.6%, thereby preventing the PID phenomenon. As of Moth-eye nanostructured optical film, the transmittance was improved by 4%, and the solar module output was improved by 2.5%.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.42.2-42.2
• /
• 2009

연속주조공정에서 용강의 통로, 산화방지 및 유체 흐름을 용이하게 하는 역할을 하는 다공성 노즐(porous nozzle)은 용강과의 직접적인 접촉으로 인한 화학 반응 및 용강의 침투현상을 방지하기 위해 불활성 가스를 주입하여 청정강을 제조하는데 이용된다. 공정 중 노즐 막힘으로 인한 배압상승과 열충격에 의한 크랙(crack) 발생이 문제되고 있으며 신뢰성 향상 연구가 요구되고 있다. 따라서 본 연구에서는 기공크기와 기공분포가 고온안정성 및 내열충격성에 미치는 영향을 알아보고, 내구성 시험 및 고장분석을 통하여 노즐의 신뢰성 향상 방안을 고찰 하였다. 기공을 제어한 시편을 제조하여 기공분포에 따른 고온안정성을 확인하기 위해 실제 사용 조건인 용강온도($1550^{\circ}C$)와 보다 높은 온도($1700^{\circ}C$)에서 각각 고온 시험을 수행하였다. 열충격을 스트레스 인자로 한 내구성 시험을 수행한 후 고장원인을 분석하였으며 열화정도를 확인하기 위해 열처리 온도에 따른 차압 및 굽힘 강도 변화를 비교하였다. 또한 결정상 분석을 통해 온도에 대한 상변화를 확인하였고, 시편의 표면 및 파단면의 미세구조 분석을 통해 크랙 발생여부를 확인하였다. 다공성 노즐의 기공분포가 균일 할수록 고온안정성 및 내열충격성이 향상됨을 확인하였고, 이를 통해 Porous Nozzle의 열화원인으로 판단되는 기공 크기 및 분포에 따른 크랙 발생에 대해 열응력 고찰을 수행하였다.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.695-700
• /
• 2014

Proton Exchange Membrane Fuel Cells (PEMFC) can generate hydrogen and oxygen from water by electrolysis. But the electrode and polymer electrolyte membrane degrade rapidly during PEM water electrolysis because of high operation voltage over 1.7V. In order to reduce the rate of anode electrode degradation, unsupported $IrO_2$ catalyst was used generally. In this study, Pt/C catalyst for PEMFC was used as a water electrolysis catalyst, and then the degradation of catalyst and membrane were analysed. After water electrolysis reaction in the voltage range from 1.8V to 2.0V, I-V curves, impedance spectra, cyclic voltammograms and linear sweep voltammetry (LSV) were measured at PEMFC operation condition. The degradation rate of electrode and membrane increased as the voltage of water electrolysis increased. The hydrogen yield was 88 % during water electrolysis for 1 min at 2.0V, the performance at 0.6V decreased to 49% due to degradation of membrane and electrode assembly.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.9
• /
• pp.110-117
• /
• 2016

Applying the contrast enhancement algorithms to luminance values of color images is a widely used approach to enhance the contrast of color images. The results obtained by this approach have reduced saturation compared with that of the original images in spite of contrast enhancement without color degradation. Applying the contrast enhancement algorithm to each channel of color images is another approach for the contrast enhancement of color images. This method produces improved images in terms of contrast and saturation while the hue of original images is changed. In this paper, main cause of color degradation is analyzed and then solving the problem based on the analysis. The channel adaptive contrast enhancement method considering characteristics of each channel is also proposed to deal with color degradation. As a result, the proposed method enhances the contrast and saturation simultaneously without color degradation. Experimental results show that the proposed method outperforms the conventional methods not only on subjective evaluation but on objective criteria.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.458-466
• /
• 2023

Structures in our surroundings deteriorate over time due to environmental and chemical factors, resulting in a decrease in their performance. The primary causes of degradation in concrete structures are carbonation, salt damage, and freeze-thaw cycles. Various maintenance methods exist to address these degradation issues. However, research and technological development for existing maintenance methods have been ongoing, but the accuracy and effectiveness of repair materials and techniques have not been extensively validated. Therefore, in this study, we conducted a material performance evaluation of various manufacturers' repair materials. Based on this evaluation, we applied corrosion inhibitors and epoxy, which are the methods most closely related to crack repair, to assess the durability performance against carbonation, salt damage, and freeze-thaw cycles. The results show approximately a two-fold performance improvement against carbonation and salt damage, and a 5% enhancement in repair performance against freeze-thaw cycles. Thus, it is considered effective in preventing rebar corrosion when appropriate maintenance is carried out according to environmental and chemical factors during structural repairs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.715-722
• /
• 2019

The durability of concrete structures deteriorates due to the corrosion of rebars and concrete deterioration by harmful ions (CO₃^2-, Cl^-, SO₄^2-) penetrating and diffusing from the outside into concrete. Therefore, the use of surface-protection finishing mortar is very important for preventing or delaying the deterioration of concrete. In this study, the possibility of the prevention of deterioration or delay of deterioration of concrete was investigated using natural latex modified with silica sol and calcium ions for cement mortar, which can be used to repair the mortar of deteriorated concrete or for finishing the mortar of concrete. As a result, fine calcium silicate hydrate was formed in the pores of the cement material due to the calcium ions and silica sol components contained in the modified latex component that reduce the pore distribution of the cement mortar, thereby reducing the penetration and diffusion of harmful ions (CO₃^2-, Cl^-, and SO₄^2-). Furthermore, the latex component was found to be present in the pores of the cement to improve the alkali resistance and carbonation resistance.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.466-473
• /
• 2016

In a shipbuilding process, thermal damage to the ship structure at the rear end results from an excessive heat input and conduction during welding process. To prevent such damage, appropriate control of the heat input, based on welding temperature measurement, is required. For temperature measurement, contact and non-contact methods are available; the thermography system is a popular non-contact temperature measurement. When the intensity of radiation from a high-temperature object is excessive, however, detecting the sensors of ordinary thermography systems leads to an inability in measuring the temperature due to saturation. Hence, this study suggests use of a neutral density filter that prevents an excessive amount of radiation from being accumulated in a thermography system, and thus makes it possible to quantitatively measure an object's temperature as high as $3000^{\circ}C$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.1
• /
• pp.39-45
• /
• 1999

Because of internal voids in insulators give rise to partial discharge(PD), which cause local breakdown and even entire insulation breakdown. Treeing due to PD is one of the main causes of breakdown of the insulating materials and nrluction of the insulation life. 1berefore the necessity for establishing a rrethod to diagnose the aging of insulation materials and to predict the breakdown of insulation has becorne irrportant. From this viewpoint, our studies diagnose insulation degradation using the rrethod of computer sensing system, which has PD and acoustic emission(AE) sensing system. To use advantages of these two methods can be used effectiveiy to search for treeing location and PD in sorre materials. In analysis rrethod of degradation, we analyzed the PD and AE pulses by regression analysis, corrpared to these obtained the correlation coefficient and retermination coefficient by T-distribution and saw that PD and AE pulses show a similar pattern on the whole. This has a similar teIlrency to the results of the research by Yoshimura and Fujita.Fujita.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.730-735
• /
• 2004

This paper describes what brings about DC offset and the impact or the DC offset on the performance or direct-conversion mobile receiver in WCDMA system. The performance degradation of $E_{b}/N_{o}$ due to the DC offset is presented through simulation result. Direct-conversion RF Transceiver which has the function of DC offset control is implemented and then applied to the WCDMA test-bed for the performance evaluation. The receiver performance degradation of $E_{c}/I_{o}$ is evaluated and analyzed by varying DC offset value. The practical test showed the minimum requirement of DC offset value to meet system performance.