• Korean Journal of Materials Research
• /
• v.4 no.2
• /
• pp.194-205
• /
• 1994

In this research, we attempt to fabricate an excellent CFRC(Carbon Fiber Reinforced Carbon), which has good thermal and mechanical properties, with 8H/satin woven fabric prepreg, high modulus and high strength type continuous carbon fiber and raw coal tar pitch(RCTP) matrix or THF soluble fraction(THFSP) matrix which has good graphitizability. Green bodies were fabricated with hot press molding technique and CFRC samples were made after carbonization, impregnation, recarbonization and graphitization steps. For the purpose of characterization of the physical properties, SEM, polarized light microscope, TGA were observed, and tested flexural strength, modulus and ILSS. After heat treating the THFSP matrix up to $2300^{\circ}C$, the value of $C_0$/2 was 3.380$\AA$, which is analogous to the structure of natural graphite and the value of 2$\theta$ is $26.276^{\circ}$ approached to the Bragg's angle of natural graphite. As a result of TGA to test the high temperature air oxidation, the THFSP matrix, graphitized up to $2300^{\circ}C$, exhibited the best air oxidation resistance. And mechanical properties were increased up to 65~70% as fiber volume fraction increased. Because of the good orientation graphitizability, the fracture surface of THFSP matrix CFRC is very good.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.111-115
• /
• 2015

To improve the efficiency of the Si solar cell, high minority carrier life time is required. Therefore, the passivation technology is important to eliminate point defects on the silicon surface, causing the loss of minority carrier recombination. PECVD or post-annealing of thermally-grown $SiO_2$ is commonly used to form the passivation layer, but a high-temperature process and low thermal stability is a critical factor of low minority carrier lifetime. In this study, atomic layer deposition was used to grow the $Al_2O_3$ passivation layer at low temperature process. $Al_2O_3$ was selected as a passivation layer which has a low surface recombination velocity because of the fixed charge density. For the high charge density, an improved minority carrier lifetime, and a low surface recombination, nitrogen was doped in the $Al_2O_3$ thin film and the improvement of passivation was studied.

• Journal of Environmental Science International
• /
• v.29 no.1
• /
• pp.69-77
• /
• 2020

Oxidative degradation of phenol, three monochlorophenols (2-chlorophenol, 2-CP; 3-chlorophenol, 3-CP; 4-chlorophenol, 4-CP), four dichlorophenols (2,3-dichlorophenol, 2,3-DCP; 2,4-dichlorophenol, 2,4-DCP; 2,5-dichlorophenol, 2,5-DCP; 2,6-dichlorophenol, 2,6-DCP), and two trichlorophenols (2,4,5-trichlorophenol, 2,4,5-TCP; 2,4,6-trichlorophenol, 2,4,6-TCP) was conducted with heat activated persulfate. As the number of chlorinations increased, the reaction rate also increased. The reaction rate was relatively well fitted to the zero-order kinetic model, rather than the pseudo-first order kinetic model for the reactions at 60 ℃, which can be explained by insufficient activation of the persulfate at 60 ℃, and the oxidation reaction of 2,4,6-TCP at 70 ℃ was relatively well fitted to the pseudo-first order kinetic model. The oxidation reaction rate generally increased with increase of persulfate concentration in the solution. 2,6-dichloro-2,5-cyclohexadiene-1,4-dione was found as a degradation product in a GC/MS analysis. This compound is a non-aromatic compound, and one chlorine was removed. This result is similar to the result of previous studies. The current study proved that heat activated persulfate activation could be an alternative remediation technology for phenol and chlorophenols in soil and groundwater.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.411.2-411.2
• /
• 2016

직접 메탄올 연료전지 (DMFCs)는 친환경적이고 낮은 작동 온도로 인한 빠른 구동, 높은 에너지 밀도 등 다양한 장점을 가지고 있어 차세대 에너지 변환소자로 많은 관심을 받고 있다. 직접 메탄올 연료전지는 메탄올을 연료로 사용하며, 메탄올이 보유하고 있는 화학적 에너지를 전기 에너지로 변환하는 장치로써 음극에서는 백금 촉매로 인한 메탄올 산화반응, 양극에서는 환원 반응이 일어나며 전기화학적 구동을 하게 된다. 하지만 일산화탄소 피독으로 인한 촉매 활성 저하, 메탄올의 cross over, 백금 촉매 사용으로 인한 고비용 등의 문제점을 가지고 있다. 따라서 많은 연구자들이 백금 사용량을 줄이고 백금 촉매를 고르게 분포하기 위해 값이 저렴하고 넓은 비표면적을 갖는 탄소계 (graphite, graphene, carbon nanotube, carbon nanofiber 등) 지지체 재료를 도입하고 있다. 이 중 탄소나노섬유 (carbon nanofibers, CNFs)는 우수한 전기전도도와 열적/화학적 안정성을 가지고 있으며, 특히 넓은 비표면적을 가지고 있어 백금 촉매의 지지체로서 많은 연구가 진행되고 있다[1]. 따라서 우리는 전기방사법을 활용하여 넓은 비표면적을 보유하는 다공성 탄소나노섬유를 성공적으로 합성하였다. 또한, 이를 백금 촉매의 지지체로 도입하여 직접 메탄올 연료전지를 위한 다공성 탄소나노섬유에 담지된 고분산성 백금 촉매를 제조하였다. 제조한 다공성 탄소나노섬유의 형상 및 구조 분석은 주사전자 현미경 (field-emission scanning electron microscopy)와 투과전자 현미경 (transmission electron microscopy)를 이용하여 분석하였고, 결정구조와 화학적 결합상태는 X-선 회절분석 (X-ray diffraction) 및 X-선 광전자 분광법 (X-ray photoelectron spectroscopy)를 이용하여 규명하였다. 전기화학적 특성은 순환 전압 전류법 (cyclic voltammetry)를 이용하였다. 이러한 실험 결과들을 바탕으로 다공성 탄소나노섬유에 담지된 고분산성 백금 촉매의 자세한 특성을 본 학회에서 다루도록 하겠다.

• Elastomers and Composites
• /
• v.43 no.4
• /
• pp.241-252
• /
• 2008

ZnAl-LDH(layered double hydroxide) modified with oleic acid(SO-ZnAl LDH) was synthesized and added to the flame retardant ABS compounds containing brominated epoxy resin(BER) and antimony trioxide(${Sb_2}{O_3}$). Flame retardant ABS compounds were manufactured by using a twin-screw co-rotating extruder and subsequently injection molded into several specimen for flame retardancy and mechanical properties. The XRD patterns of ABS nanocomposites showed no peaks. The thermal stability of ABS nanocomposites was enhanced by the addition of SO-ZnAl LDH as shown in TGA results. However, these nanocomposites showed no rating in the UL 94 vertical test at 1.6 mm thickness. Only ABS nanocomposites with additional BER more than 1.5 wt% showed UL 94 V0 rating. Notched Izod impact strength, tensile modulus, and elongation at break of flame retardant ABS nanocomposites increased with the proportion of So-ZnAl LDH whereas their melt index decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.446-446
• /
• 2009

표면 패시베이션 기술로 이용되는 수소화된 실리콘 질화막은 제조원가의 절감을 위한 실리콘 기판재료의 두께 감소에 따른 특성상의 문제점을 해결하기 위해 중요한 영향을 미치는 요소이다. 실리콘 질화막은 강한 기계적 강도, 우수한 유전적 특성, 수문에 의한 부식과 유동적 이온에 대한 우수한 저항력 때문에, 반도체 소자 산업에서 널리 사용되고 있다. 수소화된 실리콘 질화막은 반사방지 특성과 함께 표면 패시베이션의 질을 향상시킬 수 있다. 굴절률 1.9 ~ 2.3 범위에서 쉽게 변화 가능한 수소화된 실리콘 질화막은 굴절률 1.4 ~ 1.5 사이의 열적 산화막 보다 효과적인 반사방지막이다. 수소화된 실리콘 질화막을 사용한 태양전지에서는 효율을 높이기 위해서 기판 표면에서의 케리어 재결합이 억제되어져야한다. 또한, 수소화된 실리콘 질화막은 최적화된 두께와 굴절률을 가져야한다. 본 연구에서는 고효율 태양전지에 적용하기 위해 반송자 수명이 향상된 수소화된 실리콘 질화막을 플라즈마 화학 기상 증착법을 이용하여 증착하였다. 박막은 $250^{\circ}C\;{\sim}\;450^{\circ}C$에서 증착되었으며 증착된 박막은 1.94 to 2.05 굴절률 값을 가지고 있다. 반송자 수명을 증가시키기 위해 $650^{\circ}C\;{\sim}\;950^{\circ}C$에서 어닐링 하였고 반송자 수명을 측정하여 패시베이션 특성을 분석하였다. 수소화된 실리콘 질화막은 $850^{\circ}C$의 어닐링 온도와 굴절률 2.0 조건에서 가장 좋은 반송자 수명을 나타냈다.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.441-446
• /
• 2003

Fine powders of ZnO were synthesized by the sol-gel method. The shape of gel powders with calcination temperatures changed into the sheet structure, the needle shape, and the spherical grain. The growth rate of grain size was slow to 700$^{\circ}C$ but high above 700$^{\circ}C$. The bigger the grain size is, the higher the degree of crystallization is. The organic element in gel powders evaporated below 300$^{\circ}C$. Temperature dependence of conductances showed the sigmoidal shape, but the temperature range of the constant conductances narrowed with the decrement of the calcination temperature of gel powders. The optimum sensing property for CO gas were observed with the specimen calcined at 500$^{\circ}C$ and degraded with the increment of calcination temperature.

• Journal of the Korean Ceramic Society
• /
• v.41 no.9
• /
• pp.663-669
• /
• 2004

Mullite and cordierite, which were stable oxides having excellent thermal and chemical characteristics, were widely used as an engineering and electronic materials. However, thermal shock resistance of the mullite was detriorated, and strength of the cordierite was also reduced at high temperatures. The mullite-cordierite composite powders were synthesized for solving these problems in this study. The mullite-cordierite composite powders were manufactured by the solution-polymerization method using mixtures of fused silica, aluminium nitrate, magnesium nitrate, and PVA. Crystallinity, phase formation, density, and surface area of the synthesis powders were characteristics. Fine mullite-cordlerite composite powders were successfully synthesized at 1300$^{\circ}C$ and their surface areas were about 20㎡/g after planetary milling for 1h. With increasing the milling time, surface area increased to 23 ㎡/g for 4h ana 24㎡/g for 8h.

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.166-177
• /
• 2002

The present study is described of the flame structure of one-dimensional, flat, premixed, laminar, coal-air flame with some addition of methane for the flame stability. A low pressure burner operating at a combustion pressure of 0.3 arm was employed in order to extend the reaction zone. Predicted results from the models considered in the present study are compared with experimental results. Comparisons are included gas temperatures, species concentrations, char analysis and measured burning velocity. Among the models, Model II $I^{*}$-d, which specified devolatilization rate constants and a char surface area factor S=4, resulted in good agreement within the present experimental ranges. The results of char analysis suggest that the extent of the reaction occurring on the panicle might be underestimated in the model so that the char surface area should be increased. A value of 4 for this factor was given by sensitivity analysis of change in char surface area. Again, model II $I^{*}$-d gave satisfactory predictions of burning velocities over most of the experimental range studied. It has been clearly shown that the particle diameter appreciably affects the rates of devolatilisation and char oxidation through the effects of thermal lag and volumetric reactive surface area, consequently laminar burning velocity.ity.

• Polymer(Korea)
• /
• v.27 no.3
• /
• pp.249-254
• /
• 2003

The variation of chemical structure and physical properties of crosslinked polyethylene (XLPE) during thermal aging process was investigated. The formation of carbonyl functional group resulting from thermal oxidation reaction of XLPE was monitored using X-ray photoelectron spectroscopy and near infrared (NIR) spectroscopy. It was observed that the intensity of carbonyl peak observed at 1715 nm linearly increased with aging time in NIR spectroscopy. The linear relationship between NIR peak absorbance and aging time confirmed that NIR spectroscopy might be used as a proper tool for monitoring the aging process of polymeric materials. Also the formation of crosslinks during the aging process was monitored using thermal mechanical analysis, stress-strain test, and Shore hardness test. The change in the physical properties, such as the increase in the glass transition temperature from 110 to 132$^{\circ}C$, the decrease in the strain from 265 to 110%, as well as the increase in the shore D hardness from 32 to 50, was observed during the aging process.