• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.137-143
• /
• 2008

The spherical glasses lenses are typically classified into two groups such as (+) diopter lens and (-) diopter lens by the refractive power index. The thermal deformation of a lens is occurred by external heat source and is changed respected to the diopter of a lens. In this paper, the thermal deformation of spherical glasses lenses were quantitatively measured by using ESPI (electronic speckle pattern interferometry) which has an advantage that the non-contact, non-destructive and precise deformation measurement is available due to the coherency characteristic. The temperature changes were measured by IR camera. It makes experiments over 14 types of the plastic glasses lenses. From the results, it was confirmed that the larger diopter lens showed the less thermal deformation in case of the (+) diopter lens. On the other hand, the thermal deformation of the (-) diopter lens was measured with uniform pattern when the same temperature changes were applied. Also, it was found that the thermnal deformation of the (+) diopter lens is less than that of the (-) diopter lens. Therefore, it is expected that when the thermal deformation is occurred to the various types of the lens, the variation of the focal length caused by the thermal distortion of a lens would be measured quantitatively.

• The Journal of the Petrological Society of Korea
• /
• v.26 no.4
• /
• pp.361-371
• /
• 2017

We investigated geochemical characteristics of the Dodong Basaltic Rocks in the lower part of the Ulleung Island. They have lithological range of alkali basalt to trachybasalt, belonging to Na and K subseries of alkaline series. They mostly fall within the field of alkalline within-plate basalts on tectonic discrimination diagrams, and then plot in the field of oceanic island basalt (OIB). Geochemically, extension of lithospheric mantle and asthenospheric upwelling after East Sea under an Cenozoic extensional tectonic setting might be a heat source for partial melting of the enriched lithospheric mantle, which might generate the basaltic magma. But we cannot exclude that mantle plume might also be a heat source for melting of the lithospheric mantle.

• Journal of the Korean Vacuum Society
• /
• v.20 no.4
• /
• pp.307-312
• /
• 2011

As a technique for removing cancerous tumors from normal tissue, radio-frequency electromagnetic waves were employed to heating target cells up to the critical temperature, which kills the cancerous cells. However, its use in treating tumors in soft organs is limited by inconvenient factors, which are use of high-currents and long time operation. In this work, the feasibility of the localized heating by inserting four conducting electrodes with tiny direct current is investigated. The heat source is resulting from the electric field as known as resistive heating. We have investigated the temperature distribution as a function of applying DC voltages ranging from 10 V to 30 V with 10 V step. From the simulation results, the mushroom-like lesion shape by applying 20 V is generated by four electrodes within a few minutes, that is proper to the clinical application.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.387-390
• /
• 2009

본 연구에서는 유한요소 해석 상용 소프트웨어 중 하나인 ABAQUS 을 이용하여 기존의 ABAQUS 가 고려하지 못했던 상변태와 변태소성을 고려하는 프로그램을 개발하고 이를 이용하여 실제 용접 공정 해석을 수행하였다. 열원의 크기와 분포, 속도, 이동 경로 등을 모사하기 위해서 DFLUX 를,복합상에서의 재료의 열팽창 계수와 열변형률을 정의하기 위해서 UEXPAN 을 코딩하였다. 또한 재료의 상분율 및 온도에 따른 열적 구성 거동을 정의하기 위해서 UMATHT를 상변태와 그에 따른 변태소성을 반영하여 응력을 갱신하는 UMAT을 구현하였다. User Subroutine UMAT 은 아탄성 수식화와 합분해를 이용하여 증분형(Rate-form)으로 응력을 갱신하며 아탄성 수식화를 이용하여 상변태와 변태소성이 고려된 대응접선 계수가 새롭게 정의되었다. 프로그램의 타당성과 정확성을 검증하기 위해서 이미 그 정확성이 입증된 GFC(General Finite-element Code)를 사용하였다.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.99-108
• /
• 1997

Analytical model for the temperature distribution and the cooling rate of weld in dual beam laser welding is presented for investigating the possibility of controling the cooling rate. The model is based on the solutions to the problem of heat flow due to the distributed and line heat sources for preheating and welding respectively in plates with finite thickness. The effects of beam power, beam distribution parameter, interbeam distance, and welding speed on the resulting temperature distribution and cooling rate are presented. The cooling rates of dual beam laser weld at the weld centerline under the investigated conditions are reduced to as one third of those of welds which were produced by single beam laser. And it appeared that the cooling rate of dual beam laser weld is strongly dependent on the process parameters of preheating laser beam power and welding speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.42-48
• /
• 1998

This paper is concerned with the heat flux distribution and energy partition for creep-feed grinding. From measurements of transient grinding temperatures in the workpiece sub-surface using an embedded thermocouple, the overall energy partition to the workpiece was estimated from moving heat source theory for a triangular heat flux distribution as 3.0% for down grinding and 4.5% for up grinding. The higher energy partition for up grinding can be attribute to the need to satisfy thermal compatibility at the grinding zone. The influence of cooling outside the grinding zone can be analytically taken into account by specifying convective heat transfer coefficients on the workpiece surface ha ahead of the heat source (grinding zone) and hb behind the heat source. The smaller energy partition together with slightly lower grinding power favors down grinding over up grinding.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.1
• /
• pp.29-33
• /
• 2014

Recently, Difficult-to-cut materials are used in many manufacturing industry. But the difficult-to-cut materials are difficult-to-cutting process. So difficult to cut material cutting process was used after heat treatment through preheating for easy cutting process. In this study, Inconel 625 was preheating using laser heat source in computer simulation. Laser heat source temperature applied $1290^{\circ}C$ that suitable preheating temperature for Inconel 625. And temperature effects such as temperature distribution for moving heat source studied apply to similar actual process condition. Simulation results for heat treatment effects through temperature distribution verified.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.2
• /
• pp.306-314
• /
• 2008

General metal welding occurs distortion. Also, reducing distortion is required much cost. Therefore, the purpose of this study is optimization of welding conditions to reduce distortion in welding of monolithic rack housing for modular steering gear. Firstly, heat source for welding was chosen arc and laser. Secondly, it investigated optimizing welding conditions in bead welding by arc and laser heat source, and welding conditions in fillet welding was optimized with welding shapes. Finally, it was measured temperature distribution of welds by infrared camera and angle distortion in fillet welding. As a result, laser welding was superior to arc welding on distortion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.118-119
• /
• 2006

현재의 소자간 연결을 위해 사용되는 금속배선의 한계로 인해 보다 고속/대용량의 광연결(Optical Interconnection)이 크게 각광받고 있다. 본 논문에서는 FEM 시뮬레이션(Finite Element Method Simulation)을 통해 온도변화에 따른 기판에서의 온도분포를 살펴보고, 열응력 분포와 열응력 집중에 의한 기판의 변형으로 인한 문제를 연구하였다. 이를 통해 향후 Optical Passive Component 설계시 Optical Passive Component 변형의 원인이 될 수 있는 열원들의 배치를 최적화 시키고 기판의 취약부운을 보강하여 우수한 성능의 Optical Passive Component 제작을 목표로 하고 있다.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.227-231
• /
• 2000

Thermal cesium atomic beam was collimated by transversely cooling of atoms, for which circularly polarized ($\sigma^+$ and $\sigma^-$ polarized) laser light was illuminated to the atomic beam from two perpendicular directions. As a result, the temperature corresponding to the transverse velocity component could be decreased from 430 mK to 60 11K. In addition, the spatial atomic distribution was observed according to the power difference of the two laser beams and the magnetic field applied, and the result was qualitatively coincided with the calculation result by the Doppler cooling theory. heory.