• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.207-207
• /
• 2009

Aspen plus는 Aspentech사에서 개발한 공정모사용 프로그램으로서 다양한 화학종의 열역학적 자료를 기반으로 공정설계, 공정최적화, 공정모니터링 등 공정개발에 활용되고 있다. 연료개질기는 수증기 개질반응, 수성가스전이반응, 선택적화학반응으로 구성된 소규모 수소생산공정에 해당된다. 따라서 Aspen 전산모사를 통해 다양한 조건에서의 운전결과를 모사하여 개질기에 미치는 영향을 분석함으로써 운전조건을 최적화 할 수 있다. 연료개질기의 성능에 영향을 미치는 주요인자는 주로 수증기개질 촉매층 출구온도 및 수증기/탄소 비이다. 수증기개질 촉매층의 출구온도를 $660{\sim}740^{\circ}C$로 변화시키면서 개질가스의 조성, 카본 전환율, 개질효율 등을 비교 분석하였다. 또한 수증기/탄소 비를 3~5의 범위에서 변화시키면서 영향을 살펴보았다. 수증기개질 촉매층의 온도가 높을수록 수소생산량이 증가에 따른 효율 증가가 나타났으며 수증기/탄소 비가 증가할 경우에도 개질효율에 긍정적인 영향을 미치는 것을 확인하였다. 하지만 실제 개질기의 운전에서는 소재의 제약에 따라 운전 온도에 제약이 있으며 수증기/탄소비의 증가 역시 개질기의 부피 증가로 이어지는 단점이 있다는 것을 고려해야 한다. 따라서 반응기 재질, 크기, 운전온도와 개질효율과의 상관관계를 파악하여 개질기의 특성을 최적화 하여야 한다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11a
• /
• pp.210-211
• /
• 2005

• Fire Science and Engineering
• /
• v.31 no.2
• /
• pp.17-23
• /
• 2017

The test methods using convection (flame) and radiation heat sources were compared to evaluate the thermal protective performance of the firefighter's protective clothing. In particular, the influence of the outer shell, mid-layer, and lining constituting the firefighter's protective clothing on the thermal protective performance was compared for convection and radiation heat sources. Tests for the thermal protective performance were carried out according to KS K ISO 9151 (convection), KS K ISO 6942 (radiation), and KS K ISO 17492 (convection and radiation). When tested under the same incident heat flux conditions ($80kW/m^2$), the heat transfer index ($t_{12}$ and $t_{24}$) for the radiation heat source was higher than that for the convection heat source. This means that radiation has a lesser effect than convection. For the convection heat source, the lining had the greatest effect on the thermal protective performance, followed by the mid-layer and the outer shell. On the other hand, for the radiation heat source, the effect on the thermal protective performance was great in the order of lining, outer shell, and mid-layer. Convection and radiation have fundamentally different mechanisms of heat transfer, and different heat sources can lead to different thermal protective performance results depending on the material composition. Therefore, to evaluate the thermal protective performance of the firefighter's protective clothing, it is important to test not only the convection heat source, but also the radiation heat source.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.1
• /
• pp.75-94
• /
• 2019

As the present single-layer repository concept requires too large an area for the site of the repository, a multi-layer repository concept has been suggested to improve the disposal density. The effects of the excavation damaged zone around the multi-layer repository constructed in the deep host rock on the temperature distribution in the repository were analyzed. For the thermal analysis of the multi-layer repository, the hydrothermal model was used to consider the resaturation process occurring in the buffer, backfill and rock. The existence of an excavation damaged zone has a significant effect on the temperature distribution in the repository, and the maximum peak temperatures of double-layer and triple-layer repositories can rise to $7^{\circ}C$ and $12^{\circ}C$, respectively depending on the size of the excavation damaged zone and the degree of decrease of the thermal conductivity. The dominant factor affecting the peak temperature in the multi-layer repository is the decrease of thermal conductivity in the excavation damaged zone, and the excavation damaged zone formed around the deposition hole has more significant effects on the peak temperature than does the excavation damaged zone formed around the disposal tunnel.

• Nuclear Engineering and Technology
• /
• v.18 no.4
• /
• pp.273-280
• /
• 1986

The purpose of this study is to obtain the experimental data of the forced flow dryout heat flux in a heat generating debris bed which simulates the degraded nuclear reactor core after severe accident. An experimental investigation has been conducted of dryout heat flux in an inductively heated bed of steel particles with upward forced flow rising coolant circulation system under atmospheric pressure. The present observations were mainly focused on the effects of coolant mass flux, particle size, bed height, and coolant subcooling on the dryout heat flux The data were obtained when carbon steel particles in the size distribution 1.5, 2.5, 3.0 and 4.0 mm were placed in a 55 mm ID Pyrex glass column and inductively heated by passing radio frequency current through a multiturn work coil encircling the column. Distilled water was supplied with variation of mass flux from 0 to 3.5 kg/$\textrm{cm}^2$ s as a coolant in the tests, while the bed height was selected as 55 mm and 110 mm. Inlet temperature of coolant varied by 2$0^{\circ}C$ and 8$0^{\circ}C$. The principal results of the tests are: (1) Dryout heat flux increases with increase of upward forcing mass flux and particle size; (2) The dryout heat flux at the zero mass flux obviously depends on the Particle size as Previous studies; (3) The forced flow dryout heat flux in the shallow bed is somewhat higher than that in the deep bed,

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.75-82
• /
• 2005

Pyrolysis of biomass is one of the promising methods to obtain energy and valuable chemical stocks. Fast pyrolysis of Q. acutissima and L. letolepis has been carried out in a bubbling fluidized bed reactor to determine the optimum operating conditions of the pyrolyzer. Effects of reaction temperature, Uo/Umf, L/D ratio, and feed rate have been determined and the optimum conditions are as follows: $T\;=\;400^{\circ}C,\;U_o/U_{mf}\;=\;3.0,\;L/D\;=\;2.0$. Maximum yield of bio-oil was about 55% and the main compositions were carbohydrates, guaiacols, furans, phenols, and syringols. Product gas was consists of CO, $CO_2$, light hydrocarbons and the measured gas yield using the compositions agreed with the calculated value.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.382-385
• /
• 2008

박막형 태양전지 분야는 저가이고 가볍다는 특징을 가지고 있으며, 휘어지는 기판재를 적용하여 플렉서블 태양전지를 제조할 수도 있다는 장점을 가지고 있다. 본 연구에서 플렉서블 태양전지에 적합한 금속기판재를 제조하는 연구를 수행하였다. 일반적으로 기판재와 cell을 구성하는 반도체 층의 열팽창 거동 차이에 의한 열변형이 태양전지의 공정안정성에 영향을 주는 것으로 알려져 있었으며, cell을 구성하는 반도체 층과 열팽창 거동이 유사한 금속기판재의 적용이 필요하다. 이러한 특성을 쉽게 제어할 수 있는 금속기판재를 얇게 제조하기에 적절한 방법은 전주법이다. 전주법을 적용하여 조성 및 두께가 다른Ni 계 합금의 열팽창 거동을 TMA 장비를 사용하여 측정하였으며, 태양전지 제조에 사용되는 고온공정시 안정성 확보를 위하여 열처리후에 금속기판재의 열팽창 거동을 측정하였다. 그리고 전산해석tool 을 활용하여 가상의 CIS 플렉서블 태양전지 제조공정을 설정하고 고온공정온도에서 상온으로 냉각시 발생되는 층간 열변형 연구를 수행하였다. 그리고 플렉서블 태양전지용 기판재로 Ni 계 합금표면에 절연체인 $SiO_2$ 증착 연구를 수행하여 Fe-52Ni 합금에서 안정적인 절연층을 얻을 수 있었다.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.92-100
• /
• 1997

Weld repair of ASTM A-470 class 8 high pressure (HP) steam turbine rotor steel has been performed to extend the service life of older fossil units. Microhardness measurements were conducted across the weldment from unaffected base metal (BM) to weld metal (WM). The hardness of the BM was VHN 253, however it dropped up to VHN 227 at the heat affected zone (HAZ) close to unaffected BM for multipass SAW. This area of hardness drop is called "siftening zone" and has a width of 0.5-0.6mm. During creep rupture test, failure occurred around the softening zone and rupture time was 772.4hr at 19Ksi (132 Mpa) and 593.deg. C. Multipass MIG and TIG welding have been employed to reduce the softening zone width. The softening zone width for MIG was 0.3-0.4mm and for TIG was zero-0.4mm depending on heat inputs. However creep rupture time was decreased as softening zone width reduced. Creep rupture time also showed a close relationship with heat inputs in TIG process. The higher heat input, the longer rupture time. Most failure occurred at intercritical HAZ (ICHAZ), however rupture location was shifted to coarse grained HAZ (CGHAZ) as heat input decreased. The rupture surface showed tearing and dimple which indicated transgranular fracture. fracture.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.217-223
• /
• 1996

혼합증기(수증기/공기)의 막응축 열전달 계수를 수직한 벽면에서 측정하고 상관식을 개발하였다. 열전달 상관식은 액막측과 증기측으로 구분하여 만들었고, 액막측 전열계수의 상관식은 액막의 Reynolds수와 Prandtl수의 함수로 나타냈으며, 증기측 전열계수의 상관식은 증기의 Reynolds수, Prandtl수, Schmidt수 및 공기의 질량분율, 액막 Reynolds수의 함수로 제안하였다. 응축 액막의 두께와 확산층의 순간온도 측정결과로부터 액막의 파형 계면이 확산층에서의 열 및 물질전달에 큰 영향을 끼치고 있음을 확인하였고, 증기측 전열계수의 상관식에 포함된 액막 Reynolds수가 파형 계면의 영향을 반영하고 있다.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2002.11a
• /
• pp.444-446
• /
• 2002

오존은 성층권에 대부분 존재하며, 25-30km부근에서 최대 밀도를 이루고 있다. 오존층이 자외선과 그 밖의 태양복사에너지를 흡수함에 따라 성층권의 열의 근원이 되어 지구 대기 순환에 영향을 준다. 즉, 오존층이 기후변화와 밀접한 관련을 가지므로 지구의 동식물들은 그 영향을 받게 된다. 그러나 1980년대 들어서 남극에서 오존홀이 발견되고, 이 오존홀이 계속 커진다면 피해가 증가할 것이다 이 같은 상황으로 볼 때 오존의 대한 연구 필요성은 크다고 할 수 있다. (중략)