• Journal of the Korean Geotechnical Society
• /
• v.33 no.11
• /
• pp.45-57
• /
• 2017

Temperature change affects consolidation behavior of soft clays. The increase of temperature in soft clays induces the increase of pore water pressure. The dissipation of the excess pore water pressure decreases volume and void ratio. Also, the consolidation rate is accelerated by high temperature which induces the decrease of viscosity of pore fluid. The effects of temperature on the consolidation behavior such as consolidation settlement, consolidation time, and pore water pressure were investigated in this study. A numerical analysis of hydro-mechanical (HM) and thermo-hydro-mechanical (THM) behavior was performed. The combination of heat injection and sand drain for consolidating the soft ground, with varying temperature (40 and $60^{\circ}C$) and sand drain diameter (40, 60, and 80 mm), was considered. The results show that the temperature inside soil specimen increases with the increase of the temperature of heating source and the diameter of sand drain. Moreover, the heat injection increases the excess pore water pressure and, accordingly, induces additional settlement in overconsolidated (OC) state and reduces the consolidation time in normally consolidated (NC) state.

• Composites Research
• /
• v.35 no.6
• /
• pp.463-468
• /
• 2022

The high porosity of the infill pattern of carbon chopped fiber-reinforced Nylon composite structures fabricated by the fused filament fabrication (FFF) type 3D printers determines the mechanical performance of the printed structures. This study experimentally evaluated the mechanical performance of Onyx composite specimens fabricated with a rectangular infill structure under the hot-pressing condition to improve the mechanical properties by reducing the porosity of the infill pattern of the printed structure, and evaluated the best mechanical performance. The hot-pressing conditions (145℃, 4 MPa, 12 min) that induce the most appropriate mechanical properties were found. As a result of microscopic observation, it was confirmed that the infill porosity of the composite specimens subjected to post hot-pressing treatment was effectively reduced. In order to confirm the mechanical performance of the post-treated specimen, a tensile test and a three-point bending test were performed with a control specimen without post-treatment and a specimen printed with the same density and dimensions after post-treatment to evaluate the mechanical properties. As a result of comparison, it was confirmed that the mechanical properties were effectively improved when the post-treatment of hot-pressing was performed.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2000.09a
• /
• pp.105-115
• /
• 2000

As large underground projects such as radioactive waste disposal, hot water and heat storage, and geothermal energy become influential, the study, which consider all aspects of thermics, hydraulics and mechanics would be needed. Thermo Hydro-Mechanical coupling analysis is one of the most complex numerical technique because it should be implemented with the combined three governing equations to analyze the behavior of rock mass. In this study, finite element code, which is based on Biot's consolidation theory, was developed to analyze the thermo-hydro-mechanical coupling in continuum rock mass. To verify the implemented program, one-dimensional consolidation model under the isothermal and non-isothermal conditions was analyzed and was compared with the analytic solution. The parametric study on two-dimensional consolidation was also performed and the effects of several factors such as poisson's ratio and hydraulic anisotropy on rock mass behavior were investigated. In the future, this program would be revised to be used for analysis of general discontinuous media with incorporating discrete joint model.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.355-365
• /
• 2000

As large underground projects such as radioactive waste disposal, hot water and heat storage, and geothermal energy become influential, the study, which consider all aspects of thermics, hydraulics and mechanics would be needed. Thermo-Hydro-Mechanical coupling analysis is one of the most complex numerical technique because it should be implemented with the combined three governing equations to analyze the behavior of rock mass. In this study, finite element code, which is based on Biot's consolidation theory, was developed to analyze the thermo-hydro-mechanical coupling in continuum rock mass. To verify the implemented program, one-dimensional consolidation model under the isothermal and non-isothermal conditions was analyzed and was compared with the analytic solution. The parametric study on two-dimensional consolidation was also performed and the effects of several factors such as poisson's ratio and hydraulic anisotropy on rock mass behavior were investigated. In the future, this program would be revised to be used for analysis of general discontinuous media with incorporating discrete joint model.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.470-477
• /
• 2015

This study was carried out to investigate the change of dimensional stability of thermally compressed Korean pine (Pinus koraiensis Sieb. et Zucc.) wood by post heat treatment. Specific gravity of compressed wood was notably increased with thermal compression. In the compression set 50%, compressed Korean pine showed a specific gravity of 0.84. The amount of water absorption and swelling of thermally compressed Korean pine decreased with increasing temperature and time of the heat treatment. Set recovery also decreased with increasing temperature and time of heat treatment. Thermally compressed Korean pine that heat-treated in $120^{\circ}C$ for 24 hours showed a set recovery of 3.8%, whereas non-treated group showed 11.5%. Therefore, it was confirmed that the thermal treatment was a very effective method for the dimensional stability of the heat compressed wood.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.238-243
• /
• 2011

This study was estimated the change of color of compressed wood by compression temperature and time. Wood color was measured using a colorimeter and evaluated by the NBS (National Bureau of Standards) unit. As a result, the whiteness decreased with increasing compression temperature. In contrast, redness and yellowness was increased with increasing compression temperature. All of the color difference showed the 'Very Much' by NBS unit. The whiteness decreased with increasing compression time. The redness and yellowness were insignificant effect on compression temperature. In other words, the effect of compression temperature was much greater than compression time in the change of wood color.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.10
• /
• pp.5-11
• /
• 2007

This paper is to investigate the removal of the smear at elevated temperatures. This study utilized both small cylinder cell and large consolidometer apparatus to investigate the combination of PVD with heat and without heat. Two types of heaters are used in this study. The heater drain made of copper tube is used for all tests except large consolidometer and flexible wire heater is used for large consolidometer. Specimens demonstrated volume contraction upon heat and without heat. This contraction is dependent on temperature magnitude. When the specimen is heated, the magnitude of settlements is higher and rate of consolidation is faster. After treatment using PVD combined without heat and with heat for undisturbed specimens the $C_h$ values obtained were $3.45m^2/yr$ and $3.83m^2/yr$, respectively, from $3.2m^2/yr$ before treatment. The $K_h/K_s$ ratios were 3 for the specimen without heat and 2 for the specimen with heat. Similarly, in reconstituted specimens without heat and with heat, the $C_h$ values were $2.1m^2/yr$ and $2.5m^2/yr$ with $K_h/K_s$ ratios of 1.75 and 1.5, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.471-485
• /
• 2018

Post-heat treatment experiments were carried out for complete dimensional stabilization of thermally compressed wood (Pinus koraiensis). An absorption test was carried out to evaluate the dimensional stability. The specific gravity increased from 0.43 to 0.79 by thermal compression at a compression ratio of 50% thickness. Through the post-heat treatment of compressed wood, the water absorption and thickness swelling decreased with increasing the heat treatment temperature and time. In the case of the thickness recovery rate, when the heat treatment was performed for 24 hours at $120^{\circ}C$, $140^{\circ}C$ and $160^{\circ}C$, the thickness recovery was less than 1%. Therefore, it can be confirmed that the method of dimensional stabilization method of the thermal compression wood can be carried out very effectively through post heat treatment process.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.311-317
• /
• 2011

The mechanical properties of heat-compressed Radiata pine (Pinus radiata D.Don) by compression set were investigated. Heat-compression condition was temperature at $180^{\circ}C$ and press time for 60 minutes. The mechanical properties of heat-compressed wood increased with increasing compression set. Increase of the specific gravity has led to increase in mechanical properties. The maximum compression set of Radiata pine was investigated approximately 65%. It was almost same result with porosity 68% of Radiata pine in specific gravity 0.48.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.5
• /
• pp.169-178
• /
• 2002

The stress~strain characteristics of geosynthetics reinforced clayey soil were investigated by triaxial compression tests. All the tests were peformed either on unreinforced or reinforced soils under fully drained condition after having been consolidated isotropically or anisotropically to the required level of effective stresses by the small increment of 0.05kgf/$cm^2$. The anisotropically consolidated drained tests were performed to simulate the in-situ condition of reinforced soil structures such as reinforced soil wall, abutment and embankment which are generally in the anisotrpic state. From a series of tests it was ffund that the behavior of the anisotropically consolidated reinforced clayey soils was very different from stress~strain characteristics of consolidated reinferced clayey soils. It was found especially that the initial Young's moduli of anisotropically consolidated reinforced clayey soils were higher than those of isotropically consolidated reinforced clayey soils. It was found also that the reinforcement effect in anisotropically consolidated reinforced soils developed at a much lower level of axial strain(0.01%) compared with isotropically consolidated ones(about 1.0~5.0%).