• Land and Housing Review
• /
• v.2 no.1
• /
• pp.61-68
• /
• 2011

In order to clarify the structural performances of Welded Deformed Steel Bar Mats (WDSBM), the research stated includes the tests for standard hook of top bars of slab in concrete slab-wall joints, the tests for embedment length of top bar of slab, and the development strength tests for standard hook. The test results are as follows; (1) For slab-wall joints using WDSBM as reinforcement in slab, if the top bars of WDSBM are spliced by ordinary bars with sufficient development length and size, it is enough for the strength and crack control. (2) When WDSBM of slab is spliced in joint, the strength is increased with the embedment of bars of this WDSBM into wall. Beyond peak strength, however, ductility is diminished to that as no splice due to pull-out failure. (3) For slab-wall system, ultimate strain of concrete for flexural compression zone in lower surface of slab seems much greater than that of normal concrete beam. The reason is that normal concrete beam has the joint with $180^{\circ}$, however slab-wall joint has the $90^{\circ}$ of which concrete can be confined.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1994.10b
• /
• pp.15-15
• /
• 1994

M MA ODS 합금의 보다 폭넓용 실용확훌 위해 크게 요구되고 있는 적정 접합기술 개발의 한 방안￡로, 마찰압접(Friction Welding) 방법의 가능성옳 조사하기 위하여 마찰압력과 시간, 마 찰 후 접촉압력(Upset Pressure) 풍을 다양하게 변화시켜 접합체톨 제조한 후, 접합체 강도에 대한 인장시험과 접합계연의 결합 및 미세구조에 대한 현미경 관찰, EDS에 의한 원소분석, 접 합이옴부의 경도분포와 파단면 분석 풍율 행하였다. 실험에 사용된 모재는 기계적 합금법으로 제조된 Inca사의 Ni기 MA 754 합금이었으며, 직경 l 10 mm, 길이 50 mm로 가공한 후, 아세통￡로 초음파 세척하여 접합에 사용하였다. 접합온 브 레이크식 마찰압접기틀 사용하여 행하였으며, 회전시험편의 회전수는 2400 rpm이었A며, 다른 한쪽의 고정시험편과의 마찰압력 및 마찰시간온 각각 50 - 500 MPa과 1-5초로, 또한 업셋압 력도 50 - 600 MPa로 변화시켰다. 이때 업셋압력은 모든 시편에 대해 일정하게 6초동안 가하 였다. 얻어진 접합체는 각 압접조건 당 2개 이상의 접합시험편에 대해 상온 인장강도톨 측정하 였으며, 파단이 일어난 위치를 확인한 후 파면에 대한 분석율 주사전자현미경(SEM)과 에너지 분산형 분광분석기mDS)릎 사용하여 행하였다. 컵합이옴부의 첩합성올 확인하기 위하여, 접합 체를 접합변에 수직으로 절단, 연마한 후 광학현미경과 SEM, EDS 퉁으로 관찰, 분석하여 접 합부의 형상과 결합형성 여부, 접합계면의 미세조직 퉁옳 조사하였다. 또한 마찰압접에 따론 모재와 접합계연부의 경도분포훌 접합이옴부로부터 모재쪽으로 일정 간격율 두어 마이크로 비 커스 경도기로 측정, 조사하였다. 이상의 설험 결과, 다옴과 같온 결론옳 얻었다. ( (1) 접합체 강도가 모채 강도의 95% 이상이 되는 양호한 렵합체흩 얻기 위한 마찰압력 조건 온, 2400 rpm의 회전속도와 6초의 업셋압력 유지시간에서 마찰압력과 업셋압력, 그리고 마찰시 간이 각각 400 MPa 이상과 500 MPa 이상,2초입율 확인하였다. ( (2) 컵합이옴부의 관찰 결과, 모든 마찰압접 조건에서 컵합이옴부는, 기폰 모재의 texture 조직 을 유지하고 있는 모재부 영역(영역 ill)과 첩합계면부에 인접하여 업셋압력이 주어질 때 단조 효과에 의해 계연 외부로 metal flow가 일어나면서 형성된 영역 II, 매우 미세한 결정립으로 구성된 중앙부의 영역 1 로 이투어져 있옴융 확인하였다. ( (3) 최적접합조건이 충족되지 않온 경우, 접합부의 영역 I 에서 관찰된 void와 균열, 불균일한 접합계면 통의 접합결함에 Al과 Y. Ti 퉁￡로 구성된 산화물률이 용집되어 있옴을 확인하였 다-( (4) 접합체의 파단 양상온 크게 접합부 파단과 모재부 파단, 이률의 혼합형 파단i로 나눌수 있었다. 모재부 파단의 경우, 파단면이 매끄럽고 파변상의 결정립도 매우 미세하였으며, 산확물 의 용집도 찾아보기 어려웠 나, 접합부 파단의 경우에는 파변의 굴곡이 비교척 심하고 연성 입계파괴의 형태를 보였￡며, 결정립도 모채부 파단의 경우에 비해 조대하였다. 조대하였다.

• Management & Information Systems Review
• /
• v.39 no.3
• /
• pp.17-35
• /
• 2020

The purpose of this study is to develop business models for current situational scenarios reflecting customer needs emphasize the need for implementing a logistics cooperation system by analyzing big data to strengthen SCM competitiveness capacities. For healthcare SCM competitiveness needed for the logistics cooperation usage intent, they were divided into product quality, price leadership, hand-over speed, and process flexibility for examination. The wordcloud results that analyzed major considerations to realize work efficiency between medical institutes, words like unexpected situations, information sharing, delivery, real-time, delivery, convenience, etc. were mentioned frequently. It can be analyzed as expressing the need to construct a system that can immediately respond to emergency situations on the weekends. Furthermore, in addition to pursuing communication and convenience, the importance of real-time information sharing that can share to the efficiency of inventory management were evident. Accordingly, it is judged that it is necessary to aim for a business model that can enhance visibility of the logistics pipeline in real-time using big data analysis on site. By analyzing the effects of the adaptability of a supply chain network for healthcare SCM competitiveness, it was revealed that obtaining competitive capacities is possible through the implementation of logistics cooperation. Stronger partnerships such as logistics cooperation will lead to SCM competitive capacities. It will be necessary to strengthen SCM competitiveness by searching for a strategic approach among companies in a direction that can promote mutual partnerships among companies using the joint logistics system of medical institutes. In particular, it will be necessary to search for ways to utilize HCSM through big data analysis according to the construction of a logistics cooperation system.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.351-363
• /
• 2020

Launch vehicles are subject to airborne acoustic loads during atmospheric flight and these effects become pronounced especially in transonic region. As the vibration due to the acoustic loads can cause malfunction of payloads, it is essential to predict and reduce the acoustic loads. In this study, a complete process has been developed for predicting airborne vibro-acoustic environment inside the payload pairing and subsequent noise reduction procedure employing acoustic blankets and Helmholtz resonators. Acoustic loads were predicted by Reynolds-Averaged Navier-Stokes (RANS) analysis and a semi-empirical model for pressure fluctuation inside turbulent boundary layer. Coupled vibro-acoustic analysis was performed using VA One SEA's Finite Element Statistical Energy Analysis (FE-SEA) hybrid module and ANSYS APDL. The process has been applied to a hammerhead launch vehicle to evaluate the effect of acoustic load reduction and accordingly to verify the effectiveness of the process. The presently developed process enables to obtain quick analysis result with reasonable accuracy and thus is expected to be useful in the initial design phase of a launch vehicle.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.16 no.1
• /
• pp.125-133
• /
• 2010

Researches and studies which have been conducted so far on external confinement of long span concrete columns have mainly concentrated on concentric loading. But, long span bridge concrete columns over the sea are mainly subjected to concentrated axial load, and at the same time lange amount of moment by eccentric load. This paper experimentally investigates the performance of externally confined high-strength concrete columns subjected to loading mechanism and evaluates the effectiveness of two confinement materials carbon fibre and high performance glass fibre. Twelve short columns with the same dimensions were cast and tested Six columns were reinforced with hoop bars, the remaining six columns were reinforced with spiral bars and wrapped with three layers of carbon failure and high performance glass FRP sheets. Test variables considered were the shape of internal reinforcement and strengthening materials according to loading location. The experimental results showed that eccentric load could obviously lower down the maximum failure load of FRP-confined concrete columns, compared with the columns under concentric load. And compared with the carbon FRP-confined reinforced concrete columns, high performance glass FRP-confined columns displayed a higher load capacity and ductility, when tested both concentrically and eccentrically.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.8
• /
• pp.378-385
• /
• 2017

This study investigated the design of a snap fit, which is widely used for fastening plastic parts. We analyzed the assembly mechanism of a lock snapfit, measured the assembly force and separation force based on the design of experiments, and derived a regression equation through an analysis of variance. The response surface methodology was also used. Polybutylene terephthalate was used to fabricate specimens, and the assembly force and separation force were measured using a micro-tensile tester. The length, width, thickness, and interference were considered as factors. A second-order regression model was used to derive the regression equation. The assembly force decreased with increasing length and width, but it increased with increasing thickness and interference. The finite element method was used to analyze the assembly mechanics. The width decreased the assembly force by increasing the ductility. The influences of the factors for low assembly force and high release force were shown to be opposite to each other. It was necessary to design a structure that minimized the assembly force while maintaining an appropriate level of separation force.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.94-103
• /
• 2016

For elevated railway station on which track is connected with superstructure of station, structural vibration level and structure-borne-noise level has exceeded the reference level due to structural characteristics which transmits vibration directly. Therefore, existing elevated railway station is in need of economical and effective vibration reduction method which enable train service without interruption. In this study, structural vibration non-transmissible system which is applied to vibroisolating material for column member is developed to reduce vibration. That system is cut covering material of the column section using water-jet method and is installed with vibroisolating material on cut section. To verify vibration reduction effect and structural performance for structural vibration non-transmissible system, impact hammer test and cyclic lateral load test are performed for 1/4 scale test specimens. It is observed that natural period which means vibration response characteristics is shifted, and damping ratio is increased about 15~30% which means that system is effective to reduce structural vibration through vibration test. Also load-displacement relation and stiffness change rate of the columns are examined, and it is shown that ductility and energy dissipation capacity is increased. From test results, it is found that vibration non-transmissible system which is applied to column member enable to maintains structural function.

• Korean Journal of Poultry Science
• /
• v.32 no.1
• /
• pp.29-34
• /
• 2005

This study was conducted to estimate the effects of genotype for chicken major histocompatibility complex (MHC) B-LB genes on economic traits. To detect polymorphism, 400 bp fragments of MHC B-LB genes were obtained and sequenced. After digestions using restriction enzyme Hea III, two restriction enzyme sites were observed. There were two mutations at position 427 and 651 those were decided as Type I and Type II, respectively. Using RFLP analyses, type I were genotyped to TT, TC and CC, and type II to MM, Mm and mm. The relatively higher TC genotype frequencies (0.8) of Type I and Mm genotype frequencies (0.88) of Type II were observed in Korean native chickens. The effects of the genotype on 150 days body weight trait were investigated by the associations of CC and Mm genotypes (P<0.05) in Korean native chickens. This result suggests that a significant association exists between the SNP and 150 days body weight.

• Journal of Veterinary Clinics
• /
• v.31 no.6
• /
• pp.477-482
• /
• 2014

The aim of this study was to investigate and compare technique, surgical time, and complications of laparoscopic ovariectomy using $LigaSure^{TM}$ and bipolar vessel sealing system in cats. Laparoscopic ovariectomy was performed under general anesthesia on 10 healthy female cats admitted for elective ovariectomy. Surgery was performed through three midline portals. Each ovary was randomly-assigned to removal by use of either $LigaSure^{TM}$ or bipolar vessel sealing system. Duration of predetermined surgery intervals and complications were compared. Bipolar OVE ($2:16{\pm}1:14$ minutes) took significantly longer surgical time compared to the $LigaSure^{TM}$ OVE ($1:24{\pm}0:59$ minutes, P = 0.021). The ovarian pedicle fat and obesity did not influence surgery duration. Intraoperative hemorrhage occurred with bipolar OVE in three cats, but had no significant influence on surgical time. The results suggest that both $LigaSure^{TM}$ and bipolar devices appear to be effective, but $LigaSure^{TM}$ can be used as a stand-alone device that decreases surgical time and complication compared with bipolar vessel sealing system.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2003.05a
• /
• pp.51-51
• /
• 2003

임진강대의 변성이질암은 전형적인 바로비안형 변성분대를 보이며, 남쪽으로 갈수록 변성도가 증가하여 석류석$\longrightarrow$십자석$\longrightarrow$남정석 대를 정의한다. 우리는 반상변정의 성장과 여러번에 걸친 광역변형작용의 연관성을 밝히기 위해 광물의 반응관계와 성장순서 그리고 미구조(microstructure)를 -특히 석류석에 대해서- 연구하였다. 임진강대는 크게 세 번에 걸쳐 변형작용을 받은 것으로 해석된다: (1) 지각 두께의 증가에 수반된 압축변형작용 (D$_{n-1}$), (2) 주 엽리(Sn)를 만든 변형작용(Dn), 그리고 (3) 연성전단작용에 수반된 신장변형작용(D$_{n+1}$ ). 석류석대의 석류석 반상변정에서는 약간 휘어진 포유물 궤적(inclusion trail)이 주 엽리면에 대해 연속적이며, 이는 Dn과 동시기에 반상변정이 생성되었음을 지시한다. 이러한 석류석은 녹니석과 백운모로 구성된 주 엽리를 치환하면서 자라기 때문에, 녹니석+백운모+석영=석류석+흑운모+$H_2O$의 반응에 의해 만들어진 것으로 해석된다. 석류석 자형변정(idioblast)이 주 엽리를 자르면서 성장하기도 하는데, 이는 Dn 이후에도 석류석이 후구조(post-tectonic) 광물로 성장했음을 지시한다. 또한, 이러한 석류석은 흑운모를 치환하기 때문에, 동구조(syn-tectonic) 석류석의 생성반응에서와는 달리 흑운모가 반응물임을 알 수 있다. 한편, 십자석대의 석류석은 포유물 궤적에 의해 정의되는 S$_{n-1}$면이 주 엽리면과 사각을 이루며 단속적이기 때문에, D$_{n-1}$과 Dn 사이에 자란 것으로 해석된다. 이와는 대조적으로 십자석은 주 엽리를 치환하면서 자라고 있어서 Dn과 동시기 혹은 Dn 이후에 자랐을 것으로 해석된다..의 환경문제를 발생하지 않으며, 공정액에 첨가제를 투입하지 않으므로 순환형 친환경공정으로 각광받을 수 있다. 본 연구에서는 고온, 고농도의 NaOH 수용액의 처리에 적합한 막소재와 발생될 수 있는 제반 문제점 등을 파악하였고, 장기간의 실험을 거쳐 최적 투과 압력(Trans membrane pressue), 세정 조건 및 주기, 막재질에 있어서 보강하여야 할 Point, 최적 운전 조건들을 토출해 내었고, 향후 실제 Plant에 적용할 계획이다.는 양적으로 다른 두 가지의 유사한 마그마가 수반된 것으로 추정된다. 것으로 추정된다.를 사용하지 않음으로써 효과적이고 만족할 만한 심근보호 효과를 보였다.를 보였다.4주까지에서는 비교적 폐포는 정상적 구조를 유지하면서 부분적으로 소폐동맥 중막의 비후와 간질에 호산구 침윤의 소견이 특징적으로 관찰되었다. 결론: 분리 폐 관류는 정맥주입 방법에 비해 고농도의 cisplatin 투여로 인한 다른 장기에서의 농도 증가 없이 폐 조직에 약 50배 정도의 고농도 cisplatin을 투여할 수 있었으며, 또한 분리 폐 관류 시 cisplatin에 의한 직접적 폐 독성은 발견되지 않았다이 낮았으나 통계학적 의의는 없었다[10.0%(4/40) : 8.2%(20/244), p>0.05]. 결론: 비디오흉강경술에서 재발을 낮추기 위해 수술시 폐야 전체를 관찰하여 존재하는 폐기포를 놓치지 않는 것이 중요하며, 폐기포를 확인하지 못한 경우와 이차성 자연기흉에 대해서는 흉막유착술에 더 세심한 주의가 필요하다는 것을 확인하였다. 비디오흉강경수술은 통증이 적고, 입원기간이 짧고, 사회로의 복귀가 빠르며, 고위험군에 적용할 수 있고, 무엇보다도 미용상의 이점이 크다는 면에서 자연기흉에 대해 유용한 치료방법임에는 틀림이 없으나 개흉술에 비해 재발율이 높고 비용이 비싸다는 문제가 제기되고 있는 만큼 더 세심한 주의와 장기 추적관찰이 필요하리라 사료된다.전 도부타민 심초음파는 관상동맥우회로술 후