• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.6
• /
• pp.1244-1249
• /
• 2001

The characteristics of engine performance with fuel injection system in D.I. diesel engine were studied in this paper A fuel injection system has an important role in the performance and emission gas in a diesel engine. In this paper, an experimental study has been performed to verify the effect of the performance and the emission gas with the factors such as diameters of an injection nozz1e hole, diameters of an injection pipe and injection timing in the fuel injection system. The authors have obtained the results that optimizing the factors of fuel injection system is siginificant to enhance the performance of the engine system and consumption ratio of fuel, smoke, and NOx.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.5-11
• /
• 2010

분사연료의 혼합기형성과정 최적화를 통한 연소제어 기술은 디젤기관의 기관운전 및 배기특성을 향상시키기 위하여 매우 중요하다. 또한 분무의 혼합기형성 최적화를 위해서는 분사된 연료와 주위기체와의 혼합과정에 영향을 미치는 분무내부의 유동특성에 대한 연구는 필수 불가결하다. 따라서 본 연구에서는 고온 고압의 증발장에서 분무의 액상 거동에 주목하고, 그 거동특성을 통하여 증발디젤분무의 혼합기형성을 해석한다. 비정상 증발분무의 중심축에 레이저 시트광을 입사한 후, 액상분무 액적의 Mie 산란광에 의한 2차원 화상을 획득하여 증발분무 액상의 속도분포 및 와도(vorticity) 등을 구하였다. 분무의 속도분포 및 와도는 2차원 화상에 PIV법을 적용하여 계산하였다. 그림 1에 본 연구에서 구한 속도분포의 일례를 보인다. 본 연구의 결과로 상변화를 동반하는 비정상 증발장에서 구한 분무액상의 거동 특성은 상변화가 일어나지 않는 비증발장에 있어서의 분무거동특성과 유사함을 확인하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.96-102
• /
• 2004

The diesel particulate filter(DPF) is effective for particulate removal from diesel engine under a variety of conditions, and then the regeneration strategies is very important in the aspects of engine fuel consumption and engine durability. This paper addresses the changes of Peugeot 406 vehicle engine parameters(fuel injection timing, period, rail pressure, emissions exhaust temperature so on) during DPF regeneration. additionally, checked the soot loading mass with mileage and the change of fuel consumption and performance with ash accumulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.5
• /
• pp.1013-1018
• /
• 2007

In general, there are many sensors for fuel injection control such as an air flow sensor, an air intake temperature sensor, a cooling water temperature sensor, a throttle position sensor, and a motor position sensor. In this paper, we proposed a method for controlling the amount of fuel consumption in cars using fuzzy control technique by temperature change of an air intake temperature sensor and air-fuel ratio, the ratio of air and fuel mixture. In the proposed method, the amount of fuel injection is controlled by fuzzy membership functions and fuzzy inference rules established for air-fuel ratio, air intake temperature, and final fuel compensation, after computing air-fuel values using each amount of air intake and each amount of fuel injection. We verified that the proposed method is more efficient than conventional methods in fuel injection control from the results of the simulation program.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.367-375
• /
• 1986

On the hypothesis that the unstable intermediates yield by the pre-reaction of auxiliary fuel become an initiator or an explosive center which promotes the chain reaction of main fuel, various organic compounds below $C_{10}$ are injected as an auxiliary fuel prior to main injection. In the previous papers, the effects of the auxiliary fuel additions on the ignition delay period, the stability of flame, the NO concentrations in their exhaust gases have been investigated. In the present paper, to confirm where the most suitable location of lean pre-mixture for the combustion of main fuel is, and how the lean pre-mixture is contacted with main fuel, the effects of the injection timing of auxiliary fuel and the turbulence on combustion processes are investigated. Moreover, from the schlieren and color photographs of flame in the combution field, it could be found that the ignition nuclei are formed in a wider region of main spray, and that these ignition nuclei promote the development of flame, which results in the reduction of flaming duration.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.1005-1013
• /
• 2010

This study was conducted to assess the spray control of flash boiling with mixed fuel in consideration of HCCI (Homogeneous Charge Compression Ignition) engine condition. Mixed fuel existing in two phase regions can control the process of mixture formation under low temperature and density by using the spray resulting from flash boiling which is able to induce rapid evaporation of fuel spray as well as the evaporation of high boiling point component. Because HCCI engine injects the fuel early under ambient conditions, it can facilitate the chemical control of ignition combustion and physical control such as breakup and atomization of liquid fuel by flash boiling of mixed fuel which consists of highly ignitable light oil and highly volatile gasoline. This study was conducted by performing video processing after selected composition and molar fraction of the mixed fuel as major parameters and photographed Schlieren image and Mie scattered light corresponding to the flash boiling phenomenon of the fuel spray that was injected inside a constant volume vessel. It was found that flash boiling causes significant changes in the spray structure under relatively low temperature and density. Thus, we analyzed that the flash boiling spray can be used for HCCI combustion by controlling the mixture formation at the early fuel injection timing.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.1
• /
• pp.43-49
• /
• 2016

An experimental study was performed to investigate the combustion characteristics of the liquid hydrocarbon fuel atomized by an ultrasonic oscillator. Configuration of the flame was caught by the DSLR camera, and images were analyzed in detail through a post-processing. Temperature of the flame zone was measured using thermocouple. It is resulted that the flame area is proportional to the mass flow rate of carrier gas as well as the voltage applied to the ultrasonic oscillator. Temperature of the flame zone is measured and analyzed according to variation in the operating condition of the burner, too.

• Journal of the Korean Institute of Gas
• /
• v.19 no.4
• /
• pp.22-28
• /
• 2015

In order to keep the competitiveness of LPG fuel for transportation fuel, the difference in fuel consumption with gasoline and cost for an aftertreatment system should be reduced with continuous development of technology for LPG engine. In the present study, spray-guided type direct injection combustion system, whose configuration is composed of direct injector in the vicinity of spark plug, was employed to realize stable lean combustion. A certain level of nitrogen oxides($NO_x$) emits due to a locally rich mixture regions in the stratified mixture. With the application of EGR system for the reduction of $NO_x$, 15% of $NO_x$ reduction was achieved whereas fuel consumption and hydrocarbon emission increased. By the application of EGR, the combustion speed reduced especially appeared at initial flame development period and peak heat release rates and increasing rates for heat release rate decreased as EGR rate increased due to the dilution effect of intake air.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.08a
• /
• pp.67-72
• /
• 2008

본 논문에서는 하이브리드 차량 내부 전기모터의 등판 마력값과 회전 RPM, 흡기온도 센서의 온도 변화와 공기 및 연료의 혼합비율인 공연비에 대해 퍼지 제어 기법을 적용하여 차량의 연료 소비를 제어하는 방법을 제안한다. 제안된 기법에서는 초기 가속부분에서 등판 마력간과 회전 RPM을 퍼지제어 규칙에 의해 전기모터와 엔진의 사용비율을 제어하고, 엔진이 가동될 때 각각의 공기유입량과 연료 분사량을 이용하여 공연비 수치를 구한 후, 공연비, 흡기온도, 최종 연료 보정량에 대해 설정된 피지 소속 함수와 퍼지 추론 규칙에 따라 차량 연료를 제어한다. 시뮬레이션을 통하여 실험한 결과, 제안된 퍼지 제어 기법을 이용한 엔진 및 연료 제어 방법이 퍼지기법을 적용하지 않은 제어방법보다 평균연비가 개선되어 제안된 연료 제어 방법이 효율적임을 확인하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.60-65
• /
• 2003

An experimental study was performed to understand ignition characteristics of gas turbine combustor with rotating fuel injection system. Liquid fuel applied to the inner surface of rotating fuel nozzle which was driven by high speed electrical motor is flung away by centrifugal forces. The real scale combustor and test rig was manufactured and tested under atmospheric condition in KARl combustion test facility. From the test results, this combustor ignition characteristics are highly dependent upon fuel nozzle rotating speed. Futhermore, combustor exit gas temperature was rapidly changed by increasing or decreasing the fuel nozzle rotating speed.