• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.4
• /
• pp.100-111
• /
• 1994

Observations on the near-nozzle behavior of an unsteady fuel spray through single cylindrical hole nozzle were made by phase Doopler anemometer and microphotographs. At the edge of the spray, droplet velocity peaked during needle opening and closing. Droplet sizes tended to be small on the edge of spray. The near-nozzle spray angle taken from the microphotographs was time-dependent, even though it increased with gas-to-liquid density ratio as expected. The near-nozzle spray angle was the greatest on the initial stage and decreased to a relatively constant value after about one third of the total injection duration regardless of the ambient gas conditions, even in the near-vaccum condition. The wider near-nozzle spray angle in the early stage is due to the flow characteristics inside the nozzle rather than aerodynamic interactions. However, once the spray was established, aerodynamic interactions are essential in the near-nozzle atomization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.27-33
• /
• 2002

This paper presents the comparison of prediction accuracy of hybrid models. To obtain the experimental results fur comparing with the numerical results, the macroscopic and microscopic structures of the hollow-cone spray such as spray development process, spray penetration and the distribution of mean droplet size are investigated by using a shadowgraph technique and phase Doppler particle analyzer. Also, the numerical researches using various hybrid models are performed. LISA model and WAVE model are used for the primary breakup, and TAB, DDB, and RT model are used for the secondary breakup.

• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.34-42
• /
• 1998

The correlation between the droplets size and the velocity are investigated for an intermittent spray of the pintle type fuel injector employed in a port injection gasoline engine. The analysis such as the mean droplet size, SMD, and velocity under the fixed injection period and varied fuel pressures are conducted utilizing PDPA systems. As results, the experimental data obtained, show that the larger droplet sizes. the higher velocities during the spray tip arrival time, and that at Z=70mm, r=8mm, both droplet sizes and velocities are peak. At the upstream, flow of droplets are dominated by injection pressure, which are more effected inertia force of droplets at the downstream of Z=70mm.

• Journal of ILASS-Korea
• /
• v.9 no.2
• /
• pp.1-8
• /
• 2004

This work was performed to investigate the distribution of the fuel droplet size around the bluff-body and the combustion characteristics. The geometry of the bluff-body influenced the spray shape and the combustion characteristics. Diameters of the bluff-body in this experiment are 6, 8, and 10 mm and the impingement $angles({\theta})\;are\;30^{\circ},\;60^{\circ},\;and\;90^{\circ}$. The measurement points were at the distances of 20 and 30 mm axially from the nozzle. The SMD and Rosin-Rammler distribution was acquired by image processing technique (PMAS), and the mean temperatures were measured by thermocouple. The results obtained are as follows; In the condition of ${\theta}=60^{\circ}$, the values of SMD are not greatly varied compared to the other conditions. As the impingement angle of bluff-body was increased, the high temperature region was wider along radial direction. When the air-fuel ratio was increased, the CO concentration was decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.395-398
• /
• 2010

감압비등에 의한 미립화는 더 미세한 직경의 액적을 얻을 수 있고, 분무각이 증가하며, 더 좋은 혼합특성을 갖는 다는 점에서 단순 압력식 미립화와 차이가 난다. 감압비등이란 과열된 액체를 포화 압력 이하의 대기 중으로 분사하여 급격한 비등에 의해 이루어지는 미립화이다. 본 연구는 금속 연료를 이용한 추진기관의 산화제인 물 공급기술에 감압비등과정을 이용한 와류분무를 적용시키기 위해 수행됐다. 분열길이와 같은 거시적 특성은 Charge-Couple Device(CCD) 카메라를 이용해 측정하였고, Sauter Mean Diameter(SMD)와 SMD분포와 같은 미시적 특성은 Global Sizing Velocimetry(GSV) 시스템을 이용해 측정했다. 실험은 압력과 온도, 대류 속도를 변화시키며 진행했다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.16-16
• /
• 1998

로켓의 추진제에는 고체 추진제와 액체 추진제를 사용하는 두 경우로 나눌 수 있는데, 액체 추진제를 사용하는 경우, 액체 연료와 액체 산화제를 다양한 방법으로 연소실내로 분사하게 된다. 이때 사용되는 injector들 중에 impingement type이 있다. 이 type은 injector의 가공이 비교적 용이하고, 혼합성능이 좋기 때문에 LOX/RP-1(Kerosin-based hydrocarbon fuel)을 사용하는 액체 로켓엔진에서 주로 사용되어 왔다. 두 액체 jet의 충돌에 의해 액막이 형성되는데, 이 액막은 가장자리로 갈수록 두께가 얇아지며 액막표면의 파는 충돌점으로부터 멀어질수록 그 진폭의 증가를 이루어 액체의 표면장력과 관성력의 균형을 깨트리며, 이 순간 액막은 rim의 형태로 분열하여 결국에는 액적을 생성하게 된다. 현재까지의 연구내용은 충돌 jet의 형태 laminar jet과 turbulent jet으로 구분된 인젝트에 관해 연구되어왔고, 특히 국내에는 이러한 구분된 충돌 jet의 분열현상에 관한 연구결과가 미흡하다. 동일한 오르피스의 경우에도 laminar jet과 turbulent jet으로 구분되어 지며, 각각의 jet의 형태에 따라 생성되는 액막의 형상 또는 다르게 생성되어 진다. 그러므로 본 연구에서는 두 구분된 jet의 경우의 분열현상을 실험적으로 분석하였다.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.209-211
• /
• 2015

Evaporation characteristics of a single droplet of carbon nanofluids were investigated in a rapid compression machine(RCM). n-Heptane and carbon black N990 were used to synthesize the carbon nanofluids. RCM is an experimental set-up to simulate a single compression stroke of reciprocating engine. Temperature and pressure in a reaction chamber were measured during the compression stroke. After the piston reaches top dead center(TDC), temperature and pressure decreased due to the heat loss at wall. In that process, a single droplet of carbon nanofluids underwent unsteady condition. A single droplet was put at the center of reaction chamber. Thermocouple whose tip is $50{\mu}m$ was used not only to measure transient bulk temperature, but also to suspend the droplet. The picture of single droplet was taken using high speed camera with a frame rate of 500 fps. From those pictures, the droplet diameter was measured by visual basic program.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.1
• /
• pp.29-36
• /
• 2008

Spray characteristics for APU gas turbine engine are investigated. In the test, four flight conditions such as sea level idle, sea level max power, 20,000 feet idle, 20,000 feet max power are used as spray experimental conditions. Spray visualization was performed by using ND-YAG laser bean PDPA(Phase Doppler Particle Analyzer) was used for measuring the particle diameter and velocity from 20 mm to 100 mm from discharge orifice. From the test result, SMD is $90{\sim}95\;{\mu}m$ 맛 20,000 ft idle condition and SMD is $60{\sim}75\;{\mu}m$ at sea level idle condition. Also SMD is $55{\sim}65\;{\mu}m$ at 20,000 ft max power condition and SMD is $30{\sim}70\;{\mu}m$ at sea level max power condition. In the case of 20,000 ft idle condition, combustion instability could be occurred due to the higher drop diameter. Therefore it is necessary to decrease the droplet diameter in the high altitude condition.

• Fire Science and Engineering
• /
• v.24 no.1
• /
• pp.116-121
• /
• 2010

The present study has been performed to investigate the ignition characteristics of a n-dodecane fuel droplet on the hot surface. Simplified bench scale test setup was built to examine the effect of air flow on the ignition temperature of fuel droplet. IR pyrometric sensor was used to measure the surface temperature, the measured temperature using IR pyrometer was directly compared with k-type thermocouple. The ignition of n-dodecane fuel droplet was divided into two stage - cool flame and hot flame - with the air flow rate except the case of air flow rate 3.0 lpm. The ignition temperature and probability was greatly affected by the air flow rate and the MHSIT of the present study was about $300^{\circ}C$ for air flow rate of 0.5 lpm.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.19-26
• /
• 2019

Paraffin fuels usually have low combustion efficiency due to discharged unburnt droplets from the nozzle. Therefore, optimization of the post-chamber is becoming an important factor for performance. In this study, combustion experiments were conducted by changing either the length or diameter of the post-chamber to reveal the combustion behavior of paraffin fuel for hybrid rocket. As a result, the combustion efficiency improved due to the increase of the residence time as the post-chamber length increased. On the other hand, it is found that the influence of the diameter change was not significant compared with the case of variable post-chamber length.