• Journal of Energy Engineering
• /
• v.16 no.3
• /
• pp.120-127
• /
• 2007

The purpose of this study is experimentally to analyze that the fuel mass fractions of multi-component mixed fuels have an effect on the characteristics of spray ignition and combustion under the ambient conditions of diesel combustion fields. The characteristics of ignition and combustion were investigated by chemiluminescence images and direct photography. The experiments were conducted in the RCEM(rapid compression expansion machine) with optical access. Multi-component fuels mixed with i-octane, n-dodecane and n-hexadecane are injected in RCEM by the electronic control of common rail injector. Experimental conditions set up 42, 72 and 112 MPa in injection pressure, 700, 800 and 900 K in ambient gas temperature. The results show that the ignition delay was dependent on high cetane number. In case of low ambient temperature, the more low boiling point fuels were mixed, the lower luminance regime had a remarkable effect and also shortened diffusion combustion by increasing heat release rate.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.80-89
• /
• 1998

Propulsion subsystem transfers KOMPSAT into mission orbit and controls its attitude. Design factor consists of structure safety, electrical circuit design, consumable power estimation of thermal hardwares, damping device design of fuel transient pressure, and system configuration design by considering plume effect from thruster firing. System level analysis should be performed for verification of system design under launch vehicle and orbital environment. Electrical functional test of thermal control hardware, proof pressure test, cleanliness verification test, and internal/external leakage test of fuel feeding system should be carried out for performance estimation of propulsion system. Design and assembly process of propulsion subsystem was depicted and reliability of system was verified by test analysis in this paper.

• Proceedings of the KAIS Fall Conference
• /
• 2008.11a
• /
• pp.365-367
• /
• 2008

원자로 냉각계통의 압력경계를 구성하고 있는 재료들의 부식은 재료 표면에 형성되는 산화막, 금속재료의 구성성분이 용해되어 생성된 가용성 화학종 및 산화물 입자 형태의 부식생성물들을 발생시킨다. 금속합금의 부식에 의한 가용성 화학종 및 입자들의 방출은 원자로 냉각계통에서 노심과 증기발생기를 순환하면서 연료피복관 위에 침전되어 여러 가지 문제를 야기한다. 크러드는 구조재료의 부식에 기인하여 발생한 부식생성물들이 냉각수에 부유하여 떠다니거나 피복관 표면에 침적하여 형성되며 주로 니켈과 철 산화물로 구성되어 있다. 원자로 냉각계통에서 크러드를 최소화하기 위하여 수화학 조건들을 제어하지만 장주기 고연소도 노심에서 AOA 현상을 일으키는 주된 원인이 되고 있다. 피복관 위에 침적되는 크러드는 붕소의 잠복위치를 제공할 뿐만 아니라 냉각수의 압력강하를 증가시키고 피복관의 부식 및 파손 원인을 제공하며 방사선 준위가 증가하도록 한다. 따라서 본 연구에서는 반응속도론적 관점에서 원자로 정지시의 용출 크러드 특성에 대한 연구를 수행하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.229-237
• /
• 1996

For the practical use of a fuel injection system using solenoid, some mechanical and electrical problems should be explicitly analyzed. In our study, we have investigated these problems experimentally and have improved such that a solenoid driving circuit is liable to establish a fast reponse and a precise control of injection quantity. This proposed fuel injecton system is capable to control equivalence ratio from low level to high level. Therefore, we expect that this proposed system should be applicable to an actual engine.

• The Journal of Korean Institute for Practical Engineering Education
• /
• v.2 no.1
• /
• pp.154-163
• /
• 2010

The object of this study is to investigate the penetration characteristics according to the change of stacking sequences and curvature radius in the composite laminated shell. They are staked to [02/902]S and [0/902/0]s, their interlaminar number are two and four. We are manufactured to composite laminated shells with various curvature radius. Curvature radius of composite shell is 100, 150, 200mm and ${\infty}$(it's meaning flat-plate). In general, kinetic energy after impact-kinetic energy before impact increased linearly in all specimens. Absorbed energy increased linearly as the curvature increased, and absorbed energy of [02/902]S specimen, which is small interlaminar number, was higher than [0/902/0]s specimen.

• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.41-50
• /
• 2016

This study examined the combustion characteristics and emissions, fuel economy, acceleration by selecting the two fuel with octane number difference to investigate the effect on the combustion characteristics and performance of the vehicle according to the octane number. First, a single-cylinder engine was used for the combustion characteristic experiment, Of the fuel, which is distributed on the market by the selection of two different octane fuel it is performed experiments. Single cylinder experiment examined the combustion characteristics that appear when you gradually advancing the ignition timing by the ignition timing and air-fuel ratio control for each fuel and through an output, emissions, pressure, hence examined the correlation between by octane number. In addition through the actual vehicle compared the changes in the fuel octane number difference, through acceleration tests examined the impact of the octane number requirements for high-performance segment. As a result, fuel of high octane number in accordance with the ignition timing the advancing showed a slightly stable combustion characteristics, a slight increase occurred in the acceleration test and power. However, both fuel does not significantly differ from the current mode, simulating the urban and highway fuel efficiency. Therefore, the operating conditions of the vehicle currently being sold on the Effects of high-octane fuel. fuel efficiency was found insufficient.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.6
• /
• pp.389-395
• /
• 2017

This study was performed to provide the information of the soot formation behavior of octane single fuel droplet under the identical combustion conditions. To achieve this, this experimental study provide the results of the soot formation characteristics of octane droplet in accordance with different initial droplet diameter($d_0$), at the same time, experiment was conducted under the same combustion conditions which are 1.0atm of ambient pressure($P_{amb}$), 21% of oxygen concentration($O_2$) and 79% of nitrogen concentration($N_2$). Visualization of octane droplet combustion was performed by visualization system with high speed camera. The results of maximum soot volume fraction($f_{vmax}$) was almost the same under the equivalent ambient conditions regardless of initial droplet diameter. Furthermore, maximum soot volume fraction was showed the higher value in the measuring direction between $135^{\circ}$ and $315^{\circ}$ since the soot-tail is generated during two opposing igniters movement process.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.837-844
• /
• 2014

Automotive manufacturers have recently developed various technologies for improving fuel economy and satisfying enhanced emission regulations. The ultra-lean direct injection engine is a promising technology because it has the advantage of improving thermal efficiency through the deliberate control of ignition. A conventional LPG engine has been redesigned to an ultra-lean-burn LPG direct injection engine in order to adopt combustion system of ultra-lean-burn. This study is aimed at investigating the effect of a change in the compression ratio on the performance and emission characteristics of a lean-burn LPG engine. The fuel consumption, heat release rate, combustion pressure, and emission characteristics are estimated depending on changing the effect of compression ratio. When the compression ratio is increased, it is difficult to improve the fuel consumption owing to an unstable combustion state, but the total hydrocarbon and nitrogen oxide emissions are reduced.

• Environmental and Resource Economics Review
• /
• v.21 no.2
• /
• pp.211-235
• /
• 2012

This paper presents an alternative decomposition technique to identify the relative importance of factors associated with changes in $CO_2$ emissions by using directional distance function to model the joint production of desirable and undesirable outputs. The key feature of the proposed approach is the introduction of fossil and non-fossil fuel energy input efficiencies, productivity change and emission intensity change. For the 27 OECD countries as a whole, the empirical results indicate that economic growth is the most important contributor to $CO_2$ emissions increase, while efficiency change is the most important component to $CO_2$ emissions reduction between 1980 and 2007. For more extensive insights, this paper divided 3 groups according to the emission growth rate and find out that high emission countries show relatively low production efficiencies and technical changes contributing $CO_2$ emissions increase. The results also provide that more strict environmental regulations are needed to improve the pollution intensity in these countries.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.175-181
• /
• 2019

In the case of a conventional single stage decompression regulator used for large depressurization in the hydrogen fuel cell system of a fuel cell electric vehicle (FCEV), problems can arise, such as pulsation, slow response, hydrogen brittleness, leakage, high weight, and high cost due to high decompression. Most of these problems can be overcome easily using two decompression mechanisms (two-stage structures). In addition, a wide outlet-pressure control range can be secured if an electronic solenoid is applied to the second decompression. Accordingly, it is necessary to improve the precision of the outlet pressure of a two-stage pressure-reducing regulator and develop techniques, such as leakage prevention, durability, light weight, and price reduction. Therefore, to improve the outlet pressure accuracy and prevent leakage, the structural part before and after decompression to improve the air tightness were divided and the analysis was carried out assuming that the valve part was closed (open ratio: 0%) after each initial internal pressure application.