• Journal of Astronomy and Space Sciences
• /
• v.12 no.1
• /
• pp.112-122
• /
• 1995

We assume that the KOREASAT fails the entry of the geostationary orbit due to the error at the apogee kick motor firing. A simulation is done for the satellite that has a geosynochronous orbit with a non-zero degree inclination angle due to the failure at the apogee kick motor firing caused by the unbalance of the fuel storage and the spin of the thrust vector, etc. We analyzed the evolution of the orbit using the perturbation theory and calculated the changes of the eccentricity and the inclination. WHen a communication satellite has the figure eight trajectory, the beam point also traces the satellite. In this paper, We develope an algorithm to attack the above problem by stabilizing the beam point using the adjustment of the roll angle of the satellite. The spin action on the polarization plane that occurs when a satellite passes the ascending node and descending node affects the efficiency of the communication a lot, so we did another simulation for the better yaw angle adjustment for the KOREASAT to reduce the spin actino on the polarization plane.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.353-355
• /
• 2008

최근 석탄 가스화 기술은 화석연료인 석탄을 기존의 공해물질 발생을 90%이상 줄이면서 고효율로 활용할 수 있는 방법으로 각광받고 있다. 본 연구는 습식 석탄 가스화기에서 가스화의 핵심적인 요소인 버너의 분무 관계 분야에 대한 분무 특성 및 무화성능을 높일 수 있는 분무기의 구조 및 운전 조건 등을 제시 할 목적으로 분무 시 내부를 관찰 할 수 있는 아크릴을 이용하여 내부 혼합식 버너를 제작하였다. 미립화 특성을 파악하기 위하여 $O_2$/Fuel Ratio 및 버너의 내부 혼합 방식, 분사각도, 각 분사 높이에 따른 미립화 특성을 관찰하였으며, 입도 분석은 심파텍사의 입도 분석기를 이용하여 측정하였다. 내부 혼합식 버너의 입도는 분사 각도와 $O_2$/Fuel Ratio에 따라서 변화하는 경향을 나타냈으며, 공급되어지는 Fuel은 석탄 슬러리와 물을 이용하여 각각의 입도를 측정하였다. slurry의 공급량이 고정된 상태에서 산소 공급량이 증가함에 따라 미립화도는 증가하는 경향을 나타내었으며, 슬러리 공급량과 산소 공급량이 동일한 경우 버너의 분사 각도에 따라 미립화도가 다르게 나타나는 특성을 관찰하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.2
• /
• pp.248-256
• /
• 1998

The effects of fuel injection system on the performance in a V8-type diesel engine was stuided in this paper. Fuel injection system is important factor which influence the engine performance and exhaust emission bcasuse the properties in the injected fuel depend on the atomization characteristics. In this study using diesel engine of 17.7:1 compression ration the engine performance and exhaust emission are measured experimentally according to 1000, 1400, 2200rpm in the full-load conditions. The chosen parameters for the major system are such diameter shape of combustion chamber and intake system. The results are as follows: As the nozzle hole diameter and injection angle become smaller and as the injection timing gets advanced the fuel consumption and concentration of smoke are decreasing whereas concentration of $NO_{x}$ is increasing. Andconcentration of $NO_{x}$ is increasing in accordance with the increase of injection pipe diameter and nozzle protrusion. Also it is shown that re-entrant type combustion chamber is more effective than that of toroidal type in the improvement of $NO_{x}$ reduction.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.1-9
• /
• 1993

디젤 엔진의 연소 과정에서 흡입공기와 분사된 연료의 최적 혼합기 형성이 배기성분, 연료효율 등 엔진의 성능을 향상시키는데 있어 매우 중요한 과제중의 하나이다. 이를 위하여 연료분무 현상에 대한 연구와 더불어 연소실내 공기유동 현상에 대한 연구가 주요 관심대상이 되어왔다. LDV를 이용한 3-D 유속측정 및 각종 CFD Code를 이용한 유동해석등의 방법으로 엔진 실린더 내부의 유동현상을 이해하는데 많은 도움이 되고 있으나 아직도 엔진연소실설계 등 엔진 개발에 있어서는 종래의 방법에 의한 실린더내 와류 강도의 비교평가에 크게 의존하고 있으므로 여기서는 디젤 엔진의 와류를 측정 평가하는 방법으로 Paddle Wheel회전을 이용한 Paddle Wheel식 Swirl Meter방식과 실린더내 흡입공기의 각 운동량을 측정하는 Impulse식 Swirl Meter 방식에 대해 고찰하고자 한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.4
• /
• pp.83-93
• /
• 2001

A swirler with turbulence generator is designed and manufactured for generating many small-scale eddies in the combustor which contribute to enhancing mixing effect between fuel and air. The method results in not only the disadvantage of pressure loss but also the advantage of promoting combustion and reducing NOx. For the purpose of the study, four kinds of swirler with different turbulence generator area (0%, 3%, 7%, and 12% of reducing flow area) are designed to confirm the effect of mixing according the variation in the area of the turbulence generator. The mixing of combustor in the radial direction is significantly improved and the distributions of flames and temperature are well distributed throughout the cross section of a combustor as area of swirl generator is increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.60-65
• /
• 2004

Numerical simulations and experiments have been carried out to investigate the effect of fuel injection nozzles on the combustion and NOx formation processes in a medium-speed marine diesel engine. Spray visualization experiment was performed in the constant-volume high-pressure chamber to verify the numerical results on the spray characteristics such as spray angle and spray tip penetration. Time-resolved spray behaviors were captured by high-speed digital camera and analyzed to extract the information on the spray parameters. Spray and combustion phenomena were examined numerically using FIRE code. Wave breakup and Zeldovich models were adopted to describe the atomization characteristics and NOx formation processes. Numerical results were verified with experimental data such as cylinder pressure, heat release rate and NOx emission. Finally, the effects of fuel injection nozzles on the engine performance were investigated numerically to find the optimum nozzle parameters such as fuel injection angle, nozzle hole diameter and number of nozzle holes. From this study, the optimum fuel injection nozzle (nozzle hole diameter, 0.32 mm, number of nozzle holes, 8 and fuel injection angle, $148^{\circ}$) was selected to reduce both the fuel consumption and NOx emission. The reason for this selection could be explained from the highest fuel-air mixing in the early phase of injection due to the longest spray tip penetration and the highest heat release rate after $19^{\circ}$ ATDC due to the increased injection duration.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.1
• /
• pp.17-26
• /
• 2005

Both numerical analysis and cold tests for the swirl coaxial type injector were performed to obtain the influence of spray angle, velocity ratio and liquid film thickness for pressure drop and recess. The basic experimental and numerical data obtained in this study can be applicable to the performance design of swirl coaxial type injector. Spray angle was not affected by the applied test pressure drop, but spray angle was affected by tangential velocity ratio and shape factors. Feasibility of numerical analysis for the liquid film thickness and spray angle was confirmed, and the change of liquid film thickness by tangential velocity ratio affected more seriously than pressure drop, and liquid film thickness was decreased with increasing tangential velocity ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.48-56
• /
• 2008

In the rocket preburner, oxidizer-rich combustion with liquid oxygen and kerosene is very challenging work. The key factor of stable flame is good mixing and that is controlled by the injector performance. We have studied spray characteristics of the oxidizer-rich rocket preburner injector in high pressure environments. The injector is composed of fuel orifices, oxidizer orifices and cooling skirt with liquid oxygen. By using this apparatus, we have taken photographs and measured Sauter mean diameter with changing ambient pressure from 0 to 30 kgf/cm2[g]. Droplet diameter is measured by the image processing technique. From the test results, we could understand spray characteristics of the oxidizer-rich preburner injector and this result could be applied to the development of the oxidizer rich preburner system.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.5-5
• /
• 1999

3단형 과학로켓(KSR-III)의 기본형 및 응용형에 공통으로 사용되는 주엔진은 액체산소를 산화제로, 케로신을 연료로 사용하는 액체추진기관이다. 엔진 기본설계를 통하여 로켓 임무 요구사항에 부합되도록 엔진 각 부분의 기본제원을 설정하였고, 엔진의 형상을 결정하였다. 설계된 엔진의 성능검증 작업은 분사시험용 엔진, 축소형 엔진, 엔지니어링 모델 및 비행시험모델의 설계/제작/시험을 통하여 순차적으로 수행할 계획이다. 본 연구는 3단형 과학로켓 엔진의 기본설계 및 성능검증 계획에 관한 것이다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.7
• /
• pp.884-891
• /
• 2016

A secondary injection system in a diesel engine has benefits: it can be controlled independently without interrupting engine control, it can be adapted to various layouts for exhaust systems, and it pose no reductant dilution problems compared to post injection systems in the combustion chamber or other supplemental reductant injections. In a secondary injection system, the efficiency of the catalyst depends on the method of reducing the supply. The reductant needs to be maintained and optimized with constant pressure, the positions and angles of injector is a very important factor. The concentration and amount of reductant can be changed by adjusting secondary injection conditions. However, secondary injection is highly dependent upon the type of injector, injection pressure, atomization, spray technology, etc. Therefore, it is necessary to establish injection conditions the spray characteristics must be well-understood, such as spray penetration, sauter mean diameter, spray angle, injection quantity, etc. Uniform distribution of the reductant corresponding to the maximum NOx reduction in the DeNOx catalyst system must also assured. With this goal in mind, the spray characteristics and impingement plate types of a secondary injector were analyzed using visualization and digital image processing techniques.