• Tunnel and Underground Space
• /
• v.9 no.4
• /
• pp.296-305
• /
• 1999

In ordinary back analysis it if hardly possible to obtain the mechanical properties of tunnel lining by using commonly measured displacements of tunnel lining, because only a few displacements could be measured at the site. Therefore, it is necessary to develop a new method which can evaluate the state of stresses of tunnel by using measured data. In this study, in order to assess tunnel lining stability by estimating its stresses with a few measured displacements, a formulation of back analysis method was proposed. The accuracy of results were investigated through the parametric study for several types of measurement model of two dimensional elastic lining. This new back analysis method to assess tunnel lining stresses and strains with a few numbers of measured displacements showed high accuracy and good applicability when compared to the results of numerical experiments by FEM. The method has been tested on subway tunnel and its applicability has been confirmed by comparing field and analytical data. It is verified that the stress on the tunnel lining can be obtained by only more than 3 point of input displacements without any condition of external loads.

• Composites Research
• /
• v.31 no.5
• /
• pp.177-185
• /
• 2018

Fiber metal laminate (FML) is a type of hybrid composites which consist of metallic and fiber-reinforced plastic sheets. As the FML has a drawback of the delamination that is a failure of the interfacial adhesive layer, the nominal stresses and the energy release rates should be determined to identify the delamination behavior. However, it is difficult to derive the nominal stresses and the energy release rates since the operating temperature of the equipment is restricted. For this reason, the objective of this paper is to predict the mode-I nominal stress and the mode-I energy release rate of the adhesive layer using the inverse analysis based on the Levenberg-Marquardt method. First, the mode-I nominal stress was assumed as the tensile strength of the adhesive layer, and the mode-I energy release rate was obtained from the double cantilever beam test. Next, the finite element method was applied to predict the mode-I delamination behavior. Finally, the mode-I nominal stress and the mode-I energy release rate were predicted by the inverse analysis. In addition, the convergence of the parameters was validated by trying to input two cases of the initial parameters. Consequently, it is noted that the inverse analysis can predict the mode-I delamination behavior, and the two input parameters were converged to similar values.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.1
• /
• pp.112-121
• /
• 2024

The pipping system is widely used in many industries as equipment for transporting fluids over long distances. In high-pressure pipe, as the speed of the fluid increases, a loud noise is generated. Therefore, various studies have been conducted to reduce pipe noise. In this paper, a pipe noise analysis was developed to predict and quantitatively assess the flow-induced vibration and acoustic-induced vibration due to valve flow in high-temperature and high-pressure. To do this, a high-fidelity fluid analysis technique was developed for predicting internal flow in the pipe with valve. In additional, the contribution of compressible/incompressible pressure by frequency band was evaluated using the wavenumber-frequency analysis. To predict a low/middle frequency pipe noise, the vibroacoustic analysis method was developed based on Finite Element Method (FEM). And the pipe noise prediction method for the middle/high frequency was developed based on Statistical Energy Analysis (SEA).

• The Korean Journal of Rheology
• /
• v.8 no.2
• /
• pp.78-91
• /
• 1996

단섬유 보강 플라스틱 복합재료에 사출성형에서 섬유배향은 금형 충전 공정 중의 유동장에 의해 결정되고 섬유의 배향 상태는 역으로 유동장에 영향을 미친다. 단섬유에 의 한 추가적인 응력을 포함하는 Dinh과 Armstrong의 이방성 구성방정식을 충전유동과 섬유 배향의 연계해석에 도입하였다. 충전유동의 해석은 새로운 압력 지배방정식과 에너지 방정 식을 유한요소법과 유한차분법을 이용하여 풀고 동시에 2차 배향 텐서의 변화방정식을 4차 Runge-kutta 방법으로 풀었다. 섬유의 배향상태를 구한 후에 일방향성 복합재료의 Halpin-Tsai 식과 배향 평균모델을 도입하여 사풀성형품의 이방성 기계적 성질이 예측되었 다. 직사각형 캐비티에서 수치해석결과를 실험결과와 비교하였다. 섬유배향과 유동과의 상호 연계작용을 특히 게이트 근처에서 섬유배향에 영향을 미치며 수치해석 결과는 벽면 근처에 서 유동방향으로 배향하는 shell층을 과대 예측함을 알수 있었는데 이는 배향 텐서 변화 방 정식의 최종근사에서 기인하는 오차로 판단된다. 수정된 복합최종 근사를 바탕으로 예측된 이방성 기계적 성질이 기존의 복합최종 근사에 기초한 예측보다 실험 결과에 정량적으로 보 다 잘 일치하였다.

• The Korean Journal of Rheology
• /
• v.6 no.2
• /
• pp.104-118
• /
• 1994

단섬유 보강 플래스틱 재료의 사출성형 충전공정에서 금형재의 유동장이 섬유 배향 상태를 형성하는데 중요한 역할을 할 뿐만 아니라 섬유의 배향상태가 역으로 유동장에 영향 을 미친다. 충전유동과 섬유 배향의 연계해석을 위하여 단섬유에 의한 추가적인 응력을 포 함하는 Dinh과 Armstrong의 이방성 구성방정식을 충전유동의 해석에 도입하였다. 평명방향 으로의 속도구배에 의한 응력을 고려하여 새롭게 유도된 압력 지배방정식과 에너지방정식을 유한요소법과 유한차분법을 이용하여 풀고 동시에 2차배향텐서의 변화방정식을 4차 Runge-kutta 방법을 이용하여 풀었다. 절점 게이트 주변의 확장유동영역과 라인게이트를 통한 수축유동영역에서 평면방향으로의 속도구배에 의한 응력이 유동장에 미치는 영향을 고 찰하였다. 확장유동영역에서는 평면방향으로의 속도구배에 의한 영향이 추가적인 유량으로 나타나면서 주어진 유량조건하에서 평면방향으로의 속도구배에 의한 응력을 고려하지 않은 경우보다 작은 압력구배를 나타냈다. 수축유동영역에서는 위와 반대의 결과를 보였다. 이러 한 경향은 섬유의 부피분율이증가하거나 모양비가 커짐에 따라 증가한다.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.2 s.75
• /
• pp.173-181
• /
• 2005

This study deals with a method to identify damages of free vibrating thin plate structures using the combined finite element method (FEM) and the advanced uniform micro-genetic algorithm.To solve the inverse problem using the combined method, this study uses several natural frequencies instead of mode shapes in a structure as the measured data. The technique described in this paper allows us not only to detect the damaged elements but also to find their numbers, locations, and the extent of damage.To demonstrate the feasibility of the proposed method, the algorithm is applied to a free vibrating steel thin plate structures with arbitrary damages. From the standpoint of computation efficiency, the proposed method in this study has advantages when compared with the existing simple genetic algorithms. The numerical examples demonstrate that the method using micro-genetic algorithms can possibly detect correctly the damages of thin plates from only several natural frequencies instead of their natural modes.

• Geotechnical Engineering
• /
• v.12 no.3
• /
• pp.83-98
• /
• 1996

In this paper, the results of back analysis based on, the inverse method are presented. Using the field measurements obtained from the two different underground storage caverns in Korea during their construction, the deformation modulus and the initial in-situ stresses of the rock masses around the access tunnels are calculated. The finite element analysis is carried out by usinB these results as input parameters. The calculated displacements are compared with the measured ones.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.519-526
• /
• 2000

강수량 변동에 따른 사면 내의 지하수유동과 사면의 안정성 변화를 동시에 분석.평가하기 위하여 하나의 완전 연동된 수리지질역학적 모델을 제시하였다. 이 모델은 변형성 지질매체 내에서의 지하수유동을 설명하는 일련의 지배식들과 Galerkin 유한요소법에 기초하여 개발되었다. 1990년부터 1999년까지의 서울지역의 건기 (1월) 및 우기 (8월) 강수량 하에 있는 토양 사면에 대해 개발된 모델을 적용하여 일련의 수치실험을 실시하였다. 수치실험의 결과는 강수량이 증가함에 따라 사면의 수리역학적 안정성이 전반적으로 악화됨을 보여준다. 즉 강수량이 증가할수록 공극수압이 증가하고 지하수면이 상승한다. 그 결과 불포화대가 축소되고 삼출면이 팽창되며 사면의 전단부를 따라 지하수유동속도가 증가하게 된다. 동시에 강수량이 증가할수록 사면 전단부를 향해 전반적인 변위량이 증가한다. 그 결과 안전율이 1 이하인 불안전한 지역이 사면 전단부에서 사면 상부 쪽으로 전파.팽창되며 그 두께도 증가한다. 수치실험의 결과는 또한 사면의 표면에서는 전단파괴와 더불어 인장파괴도 발생할 수 있음을 보여준다.

• Economic and Environmental Geology
• /
• v.21 no.1
• /
• pp.107-113
• /
• 1988

We present a precedure for interpreting dipole-dipole apparent resistivity data. The procedure is constructed by combining a forward two-dimensional finite element modeling and an inverse technique with Householder's transformation. In the interpretation, subsurface structure is divided into some blocks with constant resistivities. Our inversion technique is tested on synthetic and field data. We found that geologic constraint is required for successful interpretation.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.126-131
• /
• 2001

One of the major obstacles in testing or evaluating precisely the thermal behavior of a machine tool is the difficulty in measuring the heat transfer coefficients on the surfaces by a conventional method. This paper presents a new approach based on the inverse method to identify the values of heat transfer coefficients by using temperature changes measured on the surfaces of a machine tool during a short period in its operating. In the present method, a machine tool structure is modeled by the finite element method and the characteristic curves of the temperature change at several points on machine tool surfaces are theoretically derived in the form that they contain the heat transfer coefficient as an unfixed heat source are approximated so that the theoretical characteristic curves of temperature change fit the measured ones as closely as possible.