• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.9A
• /
• pp.920-927
• /
• 2006

There are three critical considerations in developing a PCM telemetry encoder to be installed in an artillery projectile. The first is the performance consideration, such as sampling rate and data transmission rate. The second is the size consideration due to the severely limited installation space in an artillery projectile and the last is the power consumption consideration due to limitations of the munition's power supply. To meet these three considerations, the best alternative is a one-chip solution. Using a commercially available TMS320F2812 DSP, we have implemented a 30-channel PCM telemetry encoder to process randomized data frames, composed of 16-channel analog data, 14-channel digital data and 2-frame synchronization channels per data frame at 10Mbps transmitting baud rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4550-4560
• /
• 2011

Generally, a optical encoder is used to detect velocity for controling the electronic motor, the resolver is used when it is hard structurally to adjust encoder to electronic motor. so, the resolver has weakness in price in compare with encoder, but in case of controling the position of a magnetic polar, the resolver has stead detecting the absolute position of a rotator. This study is about the digital programing velocity detector which uses a minimum hardware : filter for detecting the revolve speed and rotor position of the motor by means of the resolver.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.432-438
• /
• 2005

In this paper, the high precision position control of AC Servo motor for semiconductor equipment is studied. The control system was implemented using TI DSP TMS320F2812 which has 150 MIPS speed for next generation motor control. The controlled 100W PMSM motor has 2,500 ppr optical incremental encoder. The control system has speed controller and current controller to control the motor position. The encoder pulses are divided into 4 times, which has 10,000 ppr and the motor system has the position accuracy of 1/10,000. If the resolution of the encoder is increased, the resolution of the position control will be increased.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.12
• /
• pp.1007-1013
• /
• 2016

This paper presents the development of a magneto-optical encoder for higher precision and smaller size. In general, optical encoders can have very high precision based on the position information of the slate, while their sizes tend to be larger due to the presence of complex and large components, such as an optical module. In contrast, magnetic encoders have exactly the opposite characteristics, i.e., small size and low precision. In order to achieve encoder features encompassing the advantages of both optical and magnetic encoders, i.e., high precision and small size, we designed a magneto-optical encoder and developed a method to detect absolute position, by compensating for the error of the hall sensor using the linear table compensation method. The performance of the magneto-optical encoder was evaluated through an experimental testbed.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.1
• /
• pp.31-39
• /
• 2014

In this paper, two calibration methods for angular vibration pickups using a precision rotary encoder are proposed. The KRISS (Korea Research Institute of Standards and Science) primary angular vibration calibration system and the calibration procedures are briefly explained. The rotary encoder is shown to be calibrated in two methods: The one is to use the laser interferometer to calibrate the rotary encoder under test and the other is to exploit the certificate of the encoder supplied. Complex sensitivities measured from the first are shown to be less than 0.1 % difference in magnitude and $0.01^{\circ}$ difference in phase shift in reference to those of the primary calibration system. Their expanded uncertainties were observed to be less than 0.6 % in magnitude and $0.4^{\circ}$ in phase shift over the range of 0.4 to 200 Hz. Under the same calibration conditions, complex sensitivities evaluated by the second method are shown be 0.1 % difference in magnitude and $0.6^{\circ}$ difference in phase shift in reference to those of the primary calibration system. Their expanded uncertainties were seen to be less than 4.8 % in magnitude and $2.8^{\circ}$ in phase shift.

• Proceedings of the Korean Reliability Society Conference
• /
• 2006.05a
• /
• pp.309-321
• /
• 2006

• Journal of Korean Electronics
• /
• v.5 no.1
• /
• pp.108-114
• /
• 1985

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.4
• /
• pp.130-135
• /
• 1999

The main scale of linear encoder greatly effects on the precision of displacement measurement. Especially when needing the long range measurement the length of main scale should be increased accordingly. In this paper we propose a linear encoder that uses laser interference pattern as main scale for long range measurement. The linear encoder is similar to Michelson interferometer excepting that the reference mirror is tilted so as to obtain interference fringe pattern and a grating panel is attached on a quadratic photo diodes. Four kinds of grating having phase difference of 0. $\pi$/4, $\pi$/2, 3$\pi$/4 are arranged on the panel. The experimental results show that signals of quadratic photo diode A, B, {{{{ {-}atop {A } }}}} and {{{{ {- } atop {B } }}}} are cosine wavelike and successive signals have phase difference of $\pi$/4 each other. So the proposed method can achieve improved measurement resolution.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.1-5
• /
• 2013

In this paper, we proposed how to estimate the walking state in the knee disarticulation prosthesis's knee angle control. In control of the knee disarticulation prosthesis, we can estimate walking state that measurement of knee angle using absolute encoder and measurement of load on the soles using strain gage. We suggested a method of estimating the current walking states which can be divided into four cases and showed the effectiveness of the method via a series of experiments.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.433-434
• /
• 2008

이 논문은 실내에서 로봇의 주행 시 생기는 오차를 수정하는 것이다. 실내에 있는 장애물(문턱)을 넘을 경우 슬립에 의하여 주행거리와 실제거리의 오차가 생기고 또한 헤드 앵글 값이 변화함에 따라서 차후 엄청난 주행 오차를 발생시키게 된다. 그에 따라 PSD 센서를 이용하여 장애물을 감지하고 감지 후 장애물을 넘을 수 있도록 모터를 제어한다. 또한 PSD를 이용하여 장애물의 크기를 계산한 후 로봇이 장애물을 넘는 동안에 엔코더 값을 받아 들여서 장애물을 넘는 동안에 로봇이 실제 이동한 거리를 측정한다. 그리고 장애물을 넘은 후에 PSD로 계산한 장애물의 크기 값과 엔코더에서 받아들인 값을 비교하여 거리오차를 수정한다. 또한 전자컴퍼스를 이용하여 장애물을 넘기 전에 로봇의 헤드 앵글 값을 구하고, 장애물을 넘은 후에 로봇의 헤드 앵글 값을 구하여 두 개의 값을 비교한다. 두 개의 값의 차이를 측정하여 수정함으로써 헤드 앵글을 오차를 수정할 수 있다.