• 한국정밀공학회지
• /
• 제17권6호
• /
• pp.89-95
• /
• 2000

The engine idle speed mode becomes worse as one drives a vehicle for several years. This is due to ageing of engine and power-train parts. In this case, unstable idle conditions such as engine stall and droop are frequently experienced when the engine gets heavy torque loads due to power steering pump and air conditioning compressor. The objective of this paper is to study on the idle speed control using PID controller under load disturbances. The input of the PID controller is an error of rpm. The output of the PID controller is an ISCV duty cycle. The dSPACE Controller Boards are used to interface with engine. The on-vehicle test is realized using by SIMULINK and BLOCKSETS tools. The real time interface control panel supplied by Control Desk S/W is designed to have good results in engine idle speed control.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.37-50
• /
• 1997

The objective of this paper is to study on the idle speed control using the fuzzy logic controller under load disturbance. The design procedure for fuzzy logic controller depends on the expert's knowledge or trial and error. The inputs of the fuzzy controller are error of rpm and variation of rpm. The output of the fuzzy controller is an ISC motor step and ignition timing. The airflow is controlled by the ISC motor movement and the idle speed is controlled by the airflow control and ignition timing control. During the control, air to fuel was checked by LAMBDA sensor. All experiments were performed in a real vehicle.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.23-29
• /
• 1994

The design procedure for fuzzy logic controller depends on the expert's knowledge or trial and error. Moreover, it is very difficult to guarantee the stability and robustness of the system due to the linguistic expression of fuzzy control. However, fuzzy logic control has succeeded in many control problems that the conventional control theory has difficulties to deal with. As a result, this control theory is applied to the engine control system which a mathematical model is difficult. In this study, the fuzzy logic is applied to obtain the gain of PI control at idle speed control system, and a simple engine model is developed in order to perform simulation. Experimental results show that the response to reach the target engine speed at idle speed control system is improved by adopting the gain obtained with fuzzy logic.

• 한국산학기술학회논문지
• /
• 제15권3호
• /
• pp.1229-1235
• /
• 2014

LPG차량의 공기 흡입 시스템에서 먼지 입자의 대부분은 공기 청정기를 통해 제거되지만, 아주 작은 입자는 제거되지 않고 흡기계통에 축적되게 된다. 이 축적된 카본은 공회전 속도 제어와 센서신호 그리고 배출가스에 영향을 주게 된다. 또한 엔진 채터링 현상이나 자동변속기의 변속시점 불량등을 야기시킨다. 이 연구는 세척액을 사용하여 흡기계통을 세척하는 것에 관한 것이다. 워밍업된 챠량에서 흡입호스를 제거하고 세척액을 사용하여 가속시에 세척액을 흡입장치에 분사시켜 흡기계통을 세척하는 것이다. 세척액을 사용하여 스로틀 바디, ISC, 서지탱크, 흡입매니폴드, 흡기밸브, 연소실까지 세척함으로서 다음과 같은 실험결과를 얻을 수 있다. 스로틀 밸브가 정확하게 작동되어 TPS의 센서 신호 전압이 개선되었으며, 차량이 정지하는 경우 ISC 시스템은 공회전 속도 제어를 원활하게 작동하였다. 또한 일산화탄소는 약 0.15 %, 탄화수소는 약 20~100PPM으로 각각 감소되어 배기가스가 현저하게 개선되었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.283-290
• /
• 2007

Recently, plastic products in air-intake parts of automotive engines have become very popular due to advantages that include reduced weight, constricted cost, and lower intake air temperature. However, flow-induced noise in air-intake parts becomes a more serious problem for plastic intake-manifolds than for conventional aluminum-made manifolds. This is due to the fact that plastic manifolds transmit more noise owing to their lower material density. Internal aerodynamic noise from an Idle Speed control Actuator (ISA) is qualitatively analyzed by using a scaling law, which is expressed with some flow parameters such as pressure drop, maximum flow velocity, and turbulence kinetic energy. First, basic flow characteristics through ISA passage are identified with the flow predictions obtained by applying Computational Fluid Dynamics techniques. Then, the effects on ISA passage noise of each design factors including the duct turning shape and vane geometries are assessed. Based on these results, the preliminary low noise design for the ISA passage are proposed. The current method for the prediction of internal aerodynamic noise consists of the steady CFD and the scaling laws for the noise prediction. This combination is most cost-effective, compared with other methods, and therefore is believed to be suited for the preliminary design tool in the industrial field.

• 한국소음진동공학회논문집
• /
• 제17권8호
• /
• pp.683-692
• /
• 2007

Recently, plastic products in air-intake parts of automotive engines have become very popular due to advantages that include reduced weight, constricted cost, and lower intake air temperature. However, flow-induced noise in air-intake parts becomes a more serious problem for plastic intake-manifolds than for conventional aluminum-made manifolds. This is due to the fact that plastic manifolds transmit more noise owing to their lower material density. Internal aerodynamic noise from an idle speed control actuator(ISA) is qualitatively analyzed by using a scaling law, which is expressed with some flow parameters such as pressure drop, maximum flow velocity, and turbulence kinetic energy. First, basic flow characteristics through ISA passage are identified with the flow predictions obtained by applying computational fluid dynamics techniques. Then, the effects on ISA passage noise of each design factors including the duct turning shape and vane geometries are assessed. Based on these results, the preliminary low noise design for the ISA passage are proposed. The current method for the prediction of internal aerodynamic noise consists of the steady CFD and the scaling laws for the noise prediction. This combination is most cost-effective, compared with other methods, and therefore is believed to be suited for the preliminary design tool in the industrial field.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제10회 학술강연회논문집
• /
• pp.6-6
• /
• 1998

중형항공기용 터보팬 엔진의 정상상태 및 천이상태 성능을 해석하고 제어기 설계를 위한 선형모델을 구하였다. 정상상태 성능해석은 설계점으로 선정한 지상정지조건과 최대상승조건(Mach=0.78, 고도=36000ft) 및 순항조건(Mach=0.78, 고도=39000ft)을 고려하였으며, 저압압축기의 공회전 상태에서 최대 회전속도까지의 부분부하성능해석을 수행하였다. 부분부하 성능해석 결과 90% RPM 조건에서 가장 연료소모율이 적어 경제적임을 알 수 있다. 동적 성능모사는 각각의 대기조건에서 연료가 Step 증가, Ramp 증가 및 감소, Step 증가 후 Ramp 감소하는 경우에 대해 수행하였다. 모사결과 고려된 모든 조건에서 연료의 Step 증가시 고압압축기의 터빈입구온도가 제한온도를 초과하여, 보다 빠른 가속과 최적의 성능을 위해서는 적절한 제어가 필요함을 알 수 있었다. 또한 최대상승조건에서 연료를 Step 증가시킬 경우 고압압축기에서 실속이 발생하여 이에 대한 대책도 필요함을 알 수 있었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.287-291
• /
• 1992

Recently, electronic engine control system is used in many automotives for high efficiency and low pollution. In order to perform these requirements, fuel injection control, spark timing control, knock control, exhaust gas recirculation control and idle speed control should be implemented. In this paper, idle speed control system using microcontroller is developed, which is compact in hardware, but powerful in software performing efficient control and various compensations for engine condition and environments. If idle speed is low engine operation is not smooth, reversely if high, fuel consumption is increased. Therefore idle speed must be maintained as low as possible within the scope that ensures smooth operation of engine. Also, an engine signal simulator, which generates various signals from engine, is realized for test facility.

• 전자공학회논문지B
• /
• 제31B권6호
• /
• pp.53-62
• /
• 1994

In this paper, a fuzzy logic-based idle speed controller is designed for automotive engine with a purpose of high efficiency and low pollution. When the idle speed is low engine operation is not smooth, otherwise fuel consumption is incresed. Therefore the idle speed must be maintained as low as possible within the scope that ensures smooth operation of engine. By simulation, we show that the idle speed controller has generated a proper control signal as engine condition or enviornment varies, and also operated well for unexpected cases. Also, an engine simulator, which is used as a basic tool for controller design, is developed and utilized for reduction of development time and cost.

• 한국군사과학기술학회지
• /
• 제18권5호
• /
• pp.492-497
• /
• 2015

Currently, there are many kinds of tracked armored vehicles in service and they have encountered various environment and situations. So there are many obstacles to operate them improperly such as an engine stall. The causes of engine stall are an insufficient fueling, a mixture of air-fuel or vapor lock, and load increment which results from a rapid steering or increasing a viscosity of lubricant by low temperature. In this paper, engine stall by load increment due to a rapid steering or increasing of lubricant viscosity on tracked armored vehicles is analyzed, the ways to prevent it are applied, and their degrees of improvement are evaluated.