• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.220-225
• /
• 2003

Recent issue of optical actuator is applying to mobile device. It leads actuator to become smaller than conventional type. This paper proposes the design of micro actuator plate spring and analysis of its vibration characteristic. Considering natural frequency of spindle motor, 1st and 2nd eigenfrequency of micro actuator must avoid its natural frequency. First, magnetic circuit is designed by using fine pattern coil and magnetic force is acquired by simulation program. Then, concept design is achieved by topology optimization. From concept design, micro actuator plate spring is embodied through DOE(design of experiment). Finally, considering vibration characteristic simultaneously, optimal plate spring design is determined by RSM(response surface method).

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.64-68
• /
• 2005

This paper proposes the rotary actuator to apply the designed actuator to the drive of the CF II size. New focus magnetic circuit is considered at this research. The rotary actuator including this circuit is designed to have the dynamic characteristic satisfying the mechanical specification as well as the portable devices. Finally, the adaptability to the portable devices was demonstrated by the finite element analysis and optimization of structural part.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.849-850
• /
• 2006

최근 자동차 브레이크의 전기적 시스템에 대한 연구가 활발히 진행되고 있다. 이와 관련하여 본 논문에서는 자기 엑추에이터 브레이크 시스템(MABS)을 분석하였다. 주행 도중 차량의 이상 및 긴급 상황 발생시 MABS는 전기적 메커니즘을 통해 차량을 제동할 수 있다. MABS는 회전하고 있는 휠에 초당 수십회 작용하여 점차적이고 효율적으로 휠을 제동한다. 이는 제동시간의 단축과 안정성에 있어 향상된 성능을 보인다. 본 연구에서는 유한요소법을 적용한 시뮬레이션을 통해 MABS의 동작 특성을 분석하고, 실제 자동차의 상황을 가정하여 제동하는데 소요되는 시간 및 작동 회수 등에 대해 분석하였다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.661-667
• /
• 2010

This paper presents a failure diagnosis and accommodation strategy which is capable of tolerating faulty actuators of a submersible vehicle. The proposed method is mainly based on a sliding mode control technique. The primary ideas include a performance index to describe the effectiveness of actuators, and a controller reconfiguration strategy using the actuator effectiveness index. The actuator effectiveness proposed in this work is defined as the relationship between the sliding surface and the controlled system behavior. The resulting actuator effectiveness is then used in reconfiguring the controller in order to counteract for the deteriorated control performance in the presence of a faulty actuator. The effectiveness of the proposed method is demonstrated by means of numerical simulations with a submersible vehicle.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.355-356
• /
• 2014

본 논문에서는 독립형 마이크로그리드에 적용되는 디젤발전기의 동작을 해석하고 디젤발전기의 실제 시스템에 대하여 고려한 모델링 및 제어에 대하여 서술한다. D-Q축의 임피던스가 서로 다른 돌극형 디젤발전기로, 제어는 조속기와 여자기로 나뉘며 엑추에이터, 디젤엔진, 그리고 여자기의 응답속도를 고려하여 모델링하였다. 조속기는 주파수를 60Hz로 유지하고 유효전력을 지령치만큼 발전한다. 여자기는 전압을 $380V_{LL}$로 유지하고 무효전력을 0으로 만드는 제어를 수행한다. 본 논문에서는 독립형 마이크로그리드에 적용되는 50kVA 디젤발전기의 조속기와 여자기를 모델링 및 제어하고 MATLAB/Simulink를 통해 디젤발전기의 동작을 해석하여 독립형 마이크로그리드에서의 운전 타당성을 증명하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1332-1340
• /
• 1992

A novel approach based on a nonlinear compensator is prposed to prevent 'windup', which is caused by the saturation of the acutator and the integral action of the controller. The anti-windup compensator is located between the conventional linear controller, designed neglecting the saturation, and the actuator. It was proven based on the describing function method that, if the closed loop control systems are stable assuming no saturation, then there may exist a range of compensator gain which prevents any limit-cycle. The computer simulation results show that the compensator proposed in the manuscript can eliminate the limit cycle and improve the transient response.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.463-466
• /
• 2005

While recent display devices are becoming light and slim, the size of a screen is especially the important issue in the field of display devices. Furthermore, it is also required that the projection TV, a large screen display device, be able to represent higher resolutions as the digital broadcasting is set off. In order to realize high resolutions in a DLP projection TV, the number of pixel on DMD should be increased. However, a large number of pixels make it difficult to realize resulting small sized pixels and this cause the increase in cost. Therefore, we propose a simple and improved pixel enhancement actuator using the existing DMD by offsetting half pixels repeatedly in the vertical direction.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.357-360
• /
• 2002

Nowadays, the improvement and development of Multi-media, information and communication technology are rapidly processed. And many products, for example, digital camera, digital camcorder, and PDA, are used for them. They need large data storage capacity and small size, light storage system. Due to that, many studies and researches in data storage system have been carried out. Especially, micro drive system was presented by IBM.(1) However, its system is expensive and uneasy to be portable. In ODD technologies, 1 inch drive system is not yet or in processing status.(2) If to be possible and to be come up, it is cheap than HDD system and easy to transfer information. In this paper, a miniaturized actuator(about linch) is designed and tested for ODD system. Specially, it is adapted for NFR(Near-field Recoding) system using SIL(Solid Immersion Lens). It is the dual-servo actuator which consists of a coarse actuator and fine actuator. Its actuating force generation method is VCM(Voice Ceil Motor). The fine actuator has 4-wire suspensions and bobbin wrapped by coil and includes focusing motion as well as tracking motion. The coarse actuator has an actuating coil and V-grooved guide mechanism. Also, the characteristics of the designed actuator is estimated by sine-swept mode and LDV(Laser Doppler Vibro-meter).

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.11
• /
• pp.1259-1264
• /
• 2011

This paper suggests a new film-type haptic actuator based on cellulose acetate electro-active paper. Conventional tiny haptic actuators in mobile devices can create vibrotactile sensation at only near resonant frequency. The strategy of operating near the resonant frequency, however, brought a new issue for creating vibrotactile sensation which can be strong enough to feel in arbitrary frequency. Another problem is that the size of the conventional actuator is not small enough to be embedded into slim mobile devices. In order to achieve these issues, we propose a thin and tiny actuator based on a cellulose acetate material charged with an electric potential. The motion of the actuator can be a concave or a convex by controlling a polarity of both charged membranes and the actuator performance can be modulated by increasing level of biased electric potential.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.48-52
• /
• 2001

In this paper presents an accurate AFM used that is free from the Z-directional distortion of a servo actuator is described. Two mathematical correction methods by the in-situ self-calibrationare employed in this AFM. One is the method by the integration, and the other is the method by inverse function of the calibration curve. The in situ self-calibration method by the integration, the derivative of the calibration curve function of the PZT actuator is calculated from the profile measurement data sets which are obtained by repeating measurements after a small Z-directional shift. Input displacement at each sampling point is approximately estimated first by using a straight calibration line. The derivative is integrated with reference to the approximate input to obtain the approximate calibration curve. Then the approximation of the input value of each sampling point is improved using the obtained calibration curve. Next the integral of the derivative is improved using the newly estimated input values. As a result of repeating these improving process, the calibration curve converges to the correct one, and the distortion of the AFM image can be corrected. In the in situ self-calibration through evaluating the inverse function of the calibration curve, the profile measurement data sets were used during the data processing technique. Principles and experimental results of the two methods are presented.