• Korean Chemical Engineering Research
• /
• v.47 no.2
• /
• pp.243-247
• /
• 2009

This study is purposed to analyze thermodynamic properties on the hydrogen production by ethylene glycol steam reforming. Various reaction conditions of temperatures(300~1,600 K), feed compositions(steam/carbon= 0.5~4.5), and pressures(1~30 atm) were applied to investigate the effects of the reaction conditions on the thermodynamic properties of dimethyl ether steam reforming. An endothermic steam reforming competed with an exothermic water gas shift reaction and an exothermic methanation within the applied reaction condition. Hydrogen production was initiated at the temperature of 400 K and the production rate was promoted at temperatures exceeding 500 K. An increase of steam to carbon ratio(S/C) in feed mixture over 1.0 resulted in the increase of the water gas shift reaction, which lowered the formation of carbon monoxide. The maximum hydrogen yield with minimizing loss of thermodynamic conversion efficiency was achieved at the reaction conditions of a temperature of 900 K and a steam to carbon ratio of 3.0.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.694-702
• /
• 2014

The micron-sized ITO(indium tin oxide) particles were prepared by spray pyrolysis from aqueous precursor solutions for indium, and tin and organic additives solution. Organic additives solution with citric acid(CA) and ethylene glycol(EG) were added to aqueous precursor solution for Indium and Tin. The obtained ITO particles prepared by spray pyrolysis from the aqueous solution without organic additives solution had spherical and filled morphologies whereas the obtained ITO particles with organic additives solution had more hollow and porous morphologies with increasing mole of organic additives. The micron-sized ITO particle with organic additives was changed fully to nano-sized ITO particle whereas the micron-sized ITO particle without organic additives was not changed fully to nano-sized ITO particle after post-treatment at $700^{\circ}C$ for 2 hours and wet-ball milling for 24 hours. The size of primary ITO particle by Debye-Scherrer formula and surface resistance of ITO pellet were measured.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.372-381
• /
• 2015

The effect of preparation method on the catalytic activities of the $Ni/Al_2O_3$ catalysts on steam reforming of ethylene glycol was investigated. The catalysts were prepared with various preparation methods such as an incipient wetness impregnation, wet impregnation, and coprecipitation method. In the case of coprecipitation method, various precipitants such as KOH, $K_2CO_3$, and $NH_4OH$ were compared. The prepared catalysts were characterized by using $N_2$ physisorption, inductively coupled plasma-atomic emission spectroscopy, X-ray diffraction, temperatureprogrammed reduction, pulsed $H_2$ chemisorption, temperature-programmed oxidation, scanning electron microscopy, and thermogravimetric analysis. Among the catalysts reduced at 773 K, the $Ni/Al_2O_3$ catalyst prepared by a coprecipitation with KOH or $K_2CO_3$ as precipitants showed the best catalytic performance. The preparation method affected the particle size of Ni, reducibility of nickel oxides, catalytic performance (activity and stability), and types of coke formed during the reaction. The $Ni/Al_2O_3$ catalyst prepared by a coprecipitation with KOH showed the increasing catalytic activity with an increase in the reduction temperature from 773 to 1173 K because of an increase in the reduction degree of Ni oxide species even though the particle size of Ni increased with increasing reduction temperature.

• Resources Recycling
• /
• v.5 no.3
• /
• pp.56-64
• /
• 1996

C,H,OH system is widely used for producing synthetic beverages and pharmaceuticals. Calcium hydroxide suspension was used to callhol the morphology of calcium carbonate, and the charactenstics of the formahan and crystsllizatian of calcium cilrbonate by adding ethylenc glycol were determined A reaclor was made with attaching a ceramic bubble plate, and lhe eleclrical conductivity was continously monitored during the rcaction with CO, gas. A part of the suspension was separated and powdered at the transition point. XRD and electron microscopic observation showed that the intermedmte and final products were vilterite, ;~r;lganite and calcite. In this study, the volumc of the ethylene glycol added to CH,OH was fixed a1 10 vol\ulcornerh. The valumc of the suspension was 500 ml, and the changes oi characteristics were shdied along with variims cnntents(l0-50 g) of calcium hydroxide. Except m the case of 10 g of calcium hydroxide at the crystallization stagc, all of products showed gelation. Tne marc the calcium hydroxide the shorter the formation time. Alsa. the farmalion of spherical valcrile ivas obsemcd when 30 g Ca(OH), was added. Tne vaterite(a compound material) can bc synthesised under alnbienl pressure and lempcmhre m a C,H,OH system by morphology control. Even though the vateritc was meta-stable phasc and could bc changed to calcitc easily, the stable and spherical vateritc was observed by using G5 glass fillers and vacuum dricrs.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.216-220
• /
• 2005

A new type of polymer gel electrolyte was prepared from poly(ethylene glycol) diacrylate(PEGDA) and 1-butyl-3-methylimidazolium bis((trifluorornethyl) sulfonyl) amide$(BuMeIm^+Tf_2N^-)$ ionic liquid. The effect of the ionic liquid on ionic conductivity of the gel polymer electrolyte was investigated. It was observed that the gel polymer electrolyte having the ionic liquid exhibited higher ionic conductivity $(ca.\;10^{-3}S/cm)$ as well as electrochemical stability than that using organic solvent.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.641-647
• /
• 2016

A drop-on-demand inkjet is used widely for various applications. Therefore, it is important to understand the jetting behavior of the drop from the piezo inkjet. In this study, to predict the jetting behavior, VOF (Volume-of-Fluid) simulation techniques were used and compared with the experimental results. The experimentally measured meniscus movement was used as the input data for the simulation. To verify the simulation, the measured jetting behavior of the mixture fluids of ethylene glycol and IPA (isopropyl alcohol), which has a mixing ratio of 50:50, was used. The numerical simulation of the drop formation using various mixture ratios and its comparison with the measured drop formation confirmed that the proposed method can predict the actual jetting. On the other hand, the satellite drop behavior showed slight differences because the small sized droplet is subject to a more aerodynamic effect during flight because the kinetic energy of the satellite droplet is far smaller than that of the main droplet.

• Clean Technology
• /
• v.19 no.3
• /
• pp.249-256
• /
• 2013

The experiments have been performed to obtain zinc complex compound with smaller particle sizes, which is used as a charge control agent in manufacturing toner. Metallic salts and polyhydric alcohols have been studied to investigate their effects on the formation and the triboelectric charge of zinc complex-compound particle with different sizes. Reactants such as zinc chloride and 3,5-di-tert.-butyl salicylic acid have been used to form the complex compound. Polyethylene glycol (PEG-300), glycerin and ethylene glycol have been added into the zinc chloride solution beforehand to lower the reaction rate in the formation of zinc complex-compound. Aluminium(III) chloride has been mixed in the zinc chloride solution beforehand to restrain the particle size from growing. When PEG-300 and aluminium(III) chloride are used to lower the reaction rate and to restrain the particle size from growing, the average particle size of zinc complex compound decreases from $5.28{\mu}m$ to $2.33{\mu}m$, which was 44.1% of $5.28{\mu}m$.

• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.25-33
• /
• 1998

The characteristics of evaporation heat transfer for the utilization of LNG cold energy was investigated experimentally using liquified nitrogen and a solution of ethylene-glycol and water under horizontal two-phase conditions in the small-scale equipment of a cryogenic heat exchange system. The inner tubes in the double pipe heat exchanger with 8 mm and 15 mm inner diameter and 6 m length were adopted as a smooth test tubes and enhanced tubes by means of wire-coil inserts. Heat transfer coefficients and Nusselt number for the test tube were calculated from measurements of temperatures, flowrates and pressures. The correlations in a power-law relationship of the Nusselt number, the Reynolds number and Prandtl number for heat transfer were proposed which can be available for design of cryogenic heat exchangers. The correlations showed heat transfer coefficients for the wire-coil inserts were much higher than those for the smooth tubes, increased by more than 2.5 ${\~}$ 5.5 times depending upon the equivalent Reynolds number. Form and length of cryogenic double pipe heat exchanger were proposed for applicable to the utilization of LNG cold energy.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.525-533
• /
• 2014

ZnO has attracted much attention such as photocatalysts, sensors, piezoelectricity and etc. At present, an economical and rapid synthesis route based on the efficient microwave polyol process is used to synthesized metal-doped ZnO nanoclusters. Diethylene glycol has a property of high polarizability, and is an excellent microwave absorbing agent, thus leading to a high heating rate and a significantly shorter reaction time. In this study, metal-doped ZnO nanoclusters are obtained with different seed volumes, when zinc acetate dihydrate is used as a precursor, and metal acetate hydrate is used as a doped-metal and diethylene glycol is used as a solvent. The obtained metal-doped ZnO nanoclusters were characterized by FE-SEM, XRD, Raman and PSA.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.464-470
• /
• 2006

Diblock copolymers consisting of methoxy Poly (ethylene glycol) (MPEG) and poly (${\epsilon}-ca$ prolactone) (PCL), poly(${\delta}-valerolactone$) (PVL), poly(L-lactide) (PLLA), or poly(L-lactide-co-glycolide) (PLGA) were prepared to compare the characterization of diblock copolymers as a drug carrier. MPEG-PCL, MPEG-PVL, MPEG-PLLA, and MPEG-PLGA diblock copolymers were synthesized by the ring-opening polymerization of ${\epsilon}$-caprolactone or ${\delta}$-valerolactone in the presence of $HCl{\cdot}Et_2O$ as a monomer activator at room temperature and by the ring-opening polymerization of L-lactide or a mixture of L-lactide and glycolide in the presence of stannous octoate at $130^{\circ}C$, respectively. The synthesized diblock copolymers were characterized with $^1H-NMR$, GPC, DSC, and XRD. The micellar characterization of MPEG-polyester diblock copolymers in an aqueous phase was carried out by using NMR, dynamic light scattering, AFM, and fluorescence techniques. Most micelles exhibited a spherical shape in AFM. Thus, ore confirmed that the micelles formed with MPEG-polyester diblock copolymers have possibility as a potential hydrophobic drug delivery vehicle because a hydrophobic drug could be preferentially distributed in the micelle core.