• Journal of computational fluids engineering
• /
• v.3 no.1
• /
• pp.89-99
• /
• 1998

한국형 차세대원자로에서는 비상노심 안전주입수가 저온관을 통하지 않고 원자로용기에 직접 주입된다. 원자로용기의 가압열충격과 열수력적 관점에서 최적의 노즐위치를 결정하기 위해서 전산유체역학을 활용하였다. 상용 전산유체코드인 CFX를 이용하여 원자로 하향유로를 모사하는 해석대상 격자를 다중불록으로 형성한 다음 유동장을 비압축성 Navier-Stokes 운동량 방정식, 에너지 방정식과 표준 k-ε 난류모형 등으로 모형화하여 3차원 비정상상태 계산을 수행하였다. CFX에서는 경계 밀착좌표계, 비엇물림격자와 SIMPLE 알고리즘을 사용한다. 본 연구결과 원자로용기의 가압열충격 관점에서 가장 보수적인 사고인 증기관 파단사고시에도 열적혼합이 잘 일어나 가압열충격이 발생할 가능성이 없는 것으로 판단되며 안전주입수 노즐이 저온관 바로 위에 위치할 때 원자로 하향유로 내의 온도 분포가 가장 균일하여 열적 혼합 관점에서는 최적의 위치로 판단된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.1049-1061
• /
• 2013

In this paper, a relative heat exchange rate is numerically compared for cast-in-place concrete energy piles with different heat exchange pipe configurations, and a new design method for energy piles is proposed. An equivalent heat exchange rate was estimated for the W-type (one series loop), multiple U-type (four parallel loops), and coil-type heat exchanger installed in the same large-diameter drilled shaft. In order to simulate a cooling operation in summer by a CFD analysis, the LWT (leaving water temperature) into a energy pile was fixed at $35^{\circ}C$ and then the EWT (entering water temperature) into a heat pump was monitored. In case of continuously applying the artificial maximum cooling load for 100 hours, all of the three types of heat exchangers show the marginally similar heat exchange rate. However, in case of intermittently applying the cooling load with a cycle of 8 hours operation-16 hours off for 7 consecutive days, the coil type heat exchanger exhibits a heat exchange rate only 86 % of the multiple U-type due to measurable thermal interference between pipe loops in the energy pile. On the other hand, the W-type possesses the similar heat exchange rate to the multiple U-type. The equivalent heat exchange rates for each configuration of heat exchangers obtained from the CFD analysis were adopted for implementing the commercial design program (PILESIM2). Finally, a design method for cast-in-place concrete energy piles is proposed along with a design chart in consideration of typical design factors.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2002

When a body enters waters, its original kinetic energy or momentum is distributed among the body and surrounding water in the form of added mass. Due to the transfer of the energy or momentum, the bode is subjected to the hydrodynamic impact forces and acceleration. This impact behavior can be an important criterion of submersible vehicle launched to the air. In this paper, based on Life-boat model, an approximate method is proposed for the evaluation of the forces and responses of cylindrical rigid bode by water entry impact. The impact forces are calculated by yon Karman's momentum theory and motion responses the body, especially acceleration, are calculated by a numerical integration of the motion equations derived by hydrodynamic force equilibrium. The proposed method is expected to be a simple but efficient tool lot the preliminary design or motion analysis of a body subjected to water entry impact.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.277-282
• /
• 2009

A temperature equation which is derived from an enthalpy transport equation by using an assumption of a constant specific heat is very attractive for analyses of heat and fluid flows. It can be used for an analysis of a solid-fluid conjugate heat transfer, and it does not need a numerical method to find temperature from a temperature-enthalpy relation. But its application is limited because of the assumption. A new method is derived in this study, which is a temperature-explicit formulation of the energy equation. The enthalpy form of the energy equation is used in the method. But the final discrete form of the equation is expressed with temperature. It can be used for a solid-fluid conjugate heat transfer and multiphase flows. It is found by numerical tests that it is very efficient and as accurate as the standard enthalpy formulation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.35.1-35.1
• /
• 2011

When the wind speed is measured by the met-mast sensor it is distorted due to the shadow effect of tower. In this paper the tower shadow effect is analyzed by a computational fluid dynamics code. First three dimensional modeling and flow analysis of the met-mast system were performed. The results were compared with the available experimental wind-tunnel test data to confirm the validity of the meshes and turbulence model. Two-dimensional model was then developed based on the three-dimensional works and experimental data. 2D analysis for various Reynolds numbers and turbulence strengths were then performed to establish the tower shadow effect database, which can be utilized as correction factors for the measured wind energy.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.269-272
• /
• 2006

Numerical analysis of wind turbine scale effect was performed by using computational fluid dynamics. For the numerical analysis of wind turbine. Three dimensional Navier-Stokes solver with various turbulence models was tested and realizable k-e turbulence model was selected for the simulation of wind turbines. To validate the present method, performance of NREL (National Renewable Energy Laboratory) Phase VI wind turbine model was analyzed and compared with experiment and blind test data. Using the present method, numerical simulations for various size of wind tunnel model were carried out and characteristics were observed in detail. The power loss due to the interference between wind turbine and nacelle was also computed for relatively larger nacelle installation in wind tunnel test. The present results showed good correlations with experimental data and reasonable trends of scale effect of wind turbine.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.356-359
• /
• 2008

본 연구는 국내 고유의 가스화기 모델 개발의 목적으로 진행되었으며 다종의 가스화기 형상을 제안하고 전산해석을 이용한 비교검토를 통하여 국내 고유의 가스화기 개념설계에 활용하고자 하였다. 우선 downflow형 가스화기 3종과 upflow형 가스화기 3종에 대한 형상을 제시하고 cold flow 해석을 통한 가스화기내 유동특성과 체류시간등을 비교하였다. 또한 고유모델로의 개발에 적합한 형상을 고려하여upflow형 2종 및 downflow형 1종 등 총 3종을 선택하여 가스화 반응을 포함시킨 hot flow 해석을 진행하고 온도분포, CO 및 $H_2$의 가스농도분포를 비교하였다. 검토 결과 기존에 연구되어왔던 석탄가스기 형태인 upflow형 가스화기 하부에 산소공급노즐을 설치하는 경우 기존에 확보된 기술을 적용함을 물론 슬랙화효율을 높이는데도 잇점이 있을 것으로 판단되었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.11
• /
• pp.871-884
• /
• 2015

Fluid transport is a key issue in the development of microfluidic systems. Recently, Myong (2014) has proposed a new concept for droplet transport without external power sources, and numerically validated the results for a hypothetical 2D shape, initially having a hemicylindrical droplet shape. Myong and Kwon (2015) have also examined the transport mechanism for an actual water droplet, initially having a 3D hemispherical shape, on a horizontal hydrophilic/hydrophobic surface, based on the numerical results of the time evolution of the droplet shape, as well as the total kinetic, gravitational, pressure and surface free energies inside the droplet. In this study, a 3D numerical analysis of an initially spherical droplet is carried out to establish a new concept for droplet transport. Further, the transport mechanism of an actual water droplet is examined in detail from the viewpoint of the capillarity force imbalance through the numerical results of droplet shape and various energies inside the droplet.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.203-210
• /
• 2014

In this study, combustion behaviour were to analyze by comparing experimental data against predicted values. In developing pellet boiler performance, various factors such as combustion chamber shape, input air velocity, the amount of fuel, temperature, and fuel characteristics need to be analyzed. Analytical model using a numerical method is useful to overcome time and cost consuming by practical experiment. By controlling feeding rate of fuel, flue gas composition and temperature distribution obtained form experiment were compared with predicted values using FLUENT(ANSYS, Inc., Southpointe). Measurement were in good agreement with model predictions : with 0.60 % for $CO_2$ 0.73% for $O_2$ when compared with independent data sets.

• Journal of Hydrogen and New Energy
• /
• v.17 no.4
• /
• pp.403-408
• /
• 2006

The plate reformer consisting of combustion chamber and reforming chamber for 25 kW MCFC stack has been operated and computational fluid dynamics was applied to estimate reactions and thermal fluid behavior in the reformer. The methane air 2-stage reaction was assumed in the combustion chamber, and three step steam reforming reactions were included in the calculation. Flow uniformity, reaction rate and species distribution, and temperature distribution were analyzed. In particular, temperature distribution was compared with the measurements to show good agreement in the combustion chamber, however, inappropriate agreement in the reformer chamber.