• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.89-96
• /
• 2011

In this study, increasing the range of replacement rate of FA with concrete properties were analyzed to provide basic data of FA replacement 0-40 % and curing temperature $5-35^{\circ}C$ range. As a result of the increased fluidity in proportion to the increase in FA, but decreased air. Setting time delayed at replacement rate increases and low temperature, simple insulation temperature history of the FA up to 40 % replacement rate increases the maximum temperature was low $8^{\circ}C$, the highest temperature reaching time delay of 13 hours. FA replacement up stream of the curing temperature, compressive strength compared to the higher plane, it was found that improved strength development. In carbonation tests with increasing the replacement ratio of FA carbonation depth was increased. Therefore, continued research on carbonation measures was to be necessary.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2015

Recently, lots of researches on concrete with high volume mineral admixture such as ground granulated blast furnace slag (GGBFS) have been carried out to reduce $CO_2$. It is known that the precast concrete has an advantage of high strength at early age due to steam curing, even if concrete has high replacement level of mineral admixture. However it demands the investigation of compressive strength properties according to steam curing regimens. In this study, concretes with water-binder ratio of 32, 35% and water content of 135, 150, $165kg/m^3$ were produced to investigate compressive strength properties of high volume (60% by mass) GGBFS cement concrete according to steam curing regimens. Then steam curing was implemented with the maximum temperature of 50, $60^{\circ}C$ and steaming time of 5, 6, 7 hours. From the test results, it was found that steam curing was effective to raise early strength of high volume GGBFS cement concrete, but 28 day compressive strengths of steam cured specimens were lower than those of water cured specimens. Thus, a further study would be needed for the optimum steam curing regimens to satisfy target demolded strength and specified strength for the application of high volume GGBFS cement concrete to precast concrete members.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.15-20
• /
• 2016

The grouting method, which can be used to effectively improve small areas within a short amount of time, may have different injection effects depending on the ground conditions and the levels of a water table. In particular, for ground with a relatively large permeability, the strength of the ground and the water proof ability can decrease over time due to the leaching process. To solve this problem, a "self-healing smart grouting (SSG) method", which was designed to maintain the initial strength of the ground by minimizing the leaching process, was developed recently. In this study, uniaxial compression tests were carried out on SSG samples to understand the strength of SSG over curing time where two different curing temperatures have been applied for comparison. The uniaxial compression strength of SSG was further compared with the samples prepared using conventional methods (LW and SGR). The test results showed that the uniaxial compression strength of SSG was higher at both high and low curing temperatures compared to that of the samples prepared using conventional methods. The initial strength of SSG was also relatively higher.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.19-28
• /
• 2018

The time for form removal is an important factor for ensuring the safety and economical efficiency of concrete structures, because it affects the quality, period, and cost of construction. Although local specifications suggest the form curing time, there is a problem of low quality of concrete due to early removing of form. This is because they do not fully understand effect of curing condition, and they want to shorten construction period in the field. Therefore, this research evaluates the effect of curing condition according to the time for form removal by testing specimen. As a result, the concrete compressive strength at the age of 28 days decreased about 40% in the condition of form removal after 12 hours, while the strength in the condition of form removal after 28 days decreased about 7%. Finally, this paper suggests an estimating equation for the concrete compressive strength due to the time for form removal considering various curing temperatures as equivalent ages. The proposed equation can be used in the field for evaluating the strength after form removal.

• Journal of the Korea Concrete Institute
• /
• v.23 no.6
• /
• pp.741-747
• /
• 2011

In this study, autogenous shrinkage strain and prediction models of concrete specimens were compared with strength level and development rate. Also, concrete autogeneous shrinkage under various curing conditions was investigated. The results showed that autogeneous shrinkage increased as concrete strength increased. However, when the concrete strength was almost identical, the initial autogeneous shrinkage of OPC was larger than BFS, but the final autogeneous shrinkage of BFS was larger than OPC. Early wet curing reduced autogeneous shrinkage strain. Especially, when the early wet curing was applied for more than 24 hours, final autogeneous shrinkage was significantly reduced. The results showed that the existing EC2 models do not reflect concrete properties properly. Therefore, the revised model was proposed to better predict autogeneous shrinkage.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.123-129
• /
• 2018

Recently, there has been a growing interest in the study of treatment of $CO_2$ generated by industrial activities and resource recycling of industrial byproducts. The aim of this study is to investigate the applicability of industrial byproducts that can be used as concrete mixed materials by carbonation curing. For this purpose, the physical and chemical changes of the pastes with research cement(RC), blast furnace slag powder (GGBFS) and circulating fluidized bed combustion ashes (CFBC) were evaluated by carbonation curing. XRD and SEM analyzes were performed to investigate micro-structural changes. As a result, it was confirmed that calcium carbonate, which is a reaction product produced by carbonation curing, filled the space inside the paste and formed a dense micro-structure. Also, as the $CO_2$ curing time increased, it was confirmed that calcium carbonate crystals were grown together to form a dense micro-structure.

• Journal of the Korea Concrete Institute
• /
• v.18 no.6 s.96
• /
• pp.759-767
• /
• 2006

This paper presents a method to estimate the setting time of concrete using super retarding agent(SRA) and fly ash(FA) under various curing temperature conditions by applying maturity based on equivalent age. To estimate setting time, the equivalent age using apparent activation energy($E_a$) was applied. Increasing SRA content and decreasing curing temperature leads to retard initial and final set markedly. $E_a$ at the initial set and final set obtained by Arrhenius function showed differences in response to mixture type. It is estimated to be from $24{\sim}35KJ/mol$ in all mixtures, which is smaller than that of conventional mixture ranging from $30{\sim}50KJ/mol$. Based on the application of $E_a$ to Freisleben-Hansen and Pederson's equivalent age function, equivalent age is nearly constant, regardless of curing temperature and SRA contents. This implies that the concept of maturity is applicable in estimating the setting time of concrete containing SRA. A high correlation between estimated setting time and measured setting time is observed. Multi-regression model to determine appropriate dosage of SRA reflecting FA contents and equivalent age was provided. Thus, the setting time estimation method studied herein can be applicable to the concrete containing SRA and FA in construction fields.

• Geotechnical Engineering
• /
• v.7 no.4
• /
• pp.49-64
• /
• 1991

Abstract The stabilization by lime or Portland cement has long been the most commonly used methods for clay soil. But it wart the purpose of this reserch to define the effectiveness malt content on unconfined compressive strength of limeflay mixture and cementrlay mixture. From result of a laboratary investigation, saInt content in sample soil was not concernd with variation of PH value. PH value of lime 10% mixture and of cement 10% mixture were near 12.4, 11.6 respectively. In case of more than 7 curing days, PH value and Ca++ion concentration were decreased with increasing curing time. Also the result of X-ray difflection analysib for stabilized soil by admixture 10% in 90 curing days showed that the diffrection intensity of Tobermorite and Ettringite and other reaction products was smaller in the case of addition of salt 8% than malt 0% in stabilized soil. When lime-soil mixture and cement-boil mixture were cured in 2$0^{\circ}C$ and 5$^{\circ}C$, 2$0^{\circ}C$ cured mizture produced significantly higher compressive strength than 5t cured mixture and air dry curing sample produced higher than cured sample in water. The addition of salt 2~4% in conjuntion with lime or cement may accelerate strenth gain or not prevent front However, the addition of salt 8% prevent from strength gams.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.309-316
• /
• 2016

In this study, performance of hardening accelerator types which promote setting and hardening of cement has been reviewed in order to develop early age strength of concrete with compressive strength of 21~27 MPa after examination of strength development of the concrete at early age according to curing temperature and unit cement(binder) content. As results, soluble mineral salt showed better hardening acceleration effect than organic salt in the scope of this study. Also, hydration reaction accelerating effect of $C_3S$ by Soluble mineral salt is effective on development of early age compressive strength and it was shown that the Pt's hydration reaction accelerating effect was the best. Construction duration reduction can be expected by securing compressive strength for prevention of early aged freezing damage in 25hour-curing time under curing temperature at $15^{\circ}C$. Also, it was shown that compressive strength of specimen cured at $5^{\circ}C$ was similar with plain specimen cured at $10^{\circ}C$. Therefore, it is expected that fuel costs and carbon dioxide can be reduced when the same construction duration is considered.

• Journal of the Korea Concrete Institute
• /
• v.26 no.6
• /
• pp.751-759
• /
• 2014

Currently, due to global warming, occurrences of extreme climate phenomena such as heat wave, heavy snow, heavy rain, super typhoon are continuously increasing all over the world. Due to these extreme climate phenomena, concrete structures and infrastructures are exposed to serious deterioration and damage. However, researches on construction technologies and standards to confront the climate change generated problems are needed presently. In order to better handle these problems, the validity of the present concrete mixture proportions are evaluated considering wind speed and sunlight exposure time based on climate change record in Seoul, Korea. The specimens cured at various wind speed and sunlight exposure time conditions were tested to obtain their compressive and split tensile strengths at various curing ages. Moreover, performance based evaluation (PBE) method was used to analyze the target strength satisfaction percentage of the concrete cured for the curing conditions. From the probabilistic method of performance evaluation of concrete performance, feasibility and usability of current concrete mix design practice for climate change conditions can be evaluated.