• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.141.1-141.1
• /
• 2014

오일 증기의 제트를 분사하여 잔류가스를 배기하는 오일확산펌프는, 구조가 간단하여 고장이 적고 저렴하며 소음 및 전기노이즈가 적게 발생하는 많은 장점을 가지고 있다. 그러나 오일의 증기압에 의해 그 도달압력이 10-9 Torr 이상으로 제한되어, 액체질소로 냉각되는 배플형태의 저온 트랩을 사용하지 않는 한 10-10 Torr영역의 초고진공 배기용으로는 사용하지 못하는 것으로 알려져 있다. 유회전펌프로 뒷받침 배기(foreline pumping)하는 700l/s의 배기속도를 가진 오일확산펌프에 300 liter/sec의 컨덕턴스를 가진 액체질소 트랩을 부착하여 메탈 실링을 사용하는 초고진공 챔버를 배기하였다. 액체질소트랩에 액체질소를 투입하면 $1{\times}10-8Pa$이하의 초고진공이 얻어졌으나, 액체질소가 증발하여 트랩의 온도가 상온으로 상승하면 압력도 $1{\times}10-7Pa$ 이상으로 상승하였다. 50 liter/sec의 배기속도를 가진 터보분자펌프로 오일확산펌프를 뒷받침 배기하면 액체질소를 투입하지 않은 상태에서 $5{\times}10-9Pa$이하의 초고진공이 얻어졌으며, 액체질소를 투입하여도 압력은 거의 변화하지 않았다. 잔류가스분석장치로 얻은 잔류가스 성분 스펙트럼은 수소가 잔류가스의 대부분을 차지하는 것을 보여주었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.181-184
• /
• 2006

We successfully completed the development test for a 10-ton thrust liquid rocket engine using LOX+LNG (Liquefied Natural Gas, or Methane) with a high performance turbopump system. Resulting from the success of the regenerative-cooling capability using LNG, high pressure-generating capability and gas-generating performance, etc, methane engine with the product name CHASE-10 will be commercialized in the near future.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.8
• /
• pp.805-811
• /
• 2009

An oxidizer pump of a turbopump for a 30-ton class gas generator cycle engine was tested in the medium of liquid oxygen. The turbine was driven by cold hydrogen gas in the test. The oxidizer pump was operated stably at both design and off-design conditions, satisfying the performance requirements. The pump head coefficient from the liquid oxygen test was 2~3% lower than that from the water test. The power required to run the oxidizer pump was well balanced with the power produced by the turbine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.375-383
• /
• 2005

The present paper describes the first development of a LOX/kerosene type turbopump in Korea. The liquid rocket engine, that the turbopump can be applied to, has a 30-ton(metric) level of vacuum thrust and employs a gas generator cycle. The turbopump consists of two single-stage centrifugal pumps, that is, LOX and kerosene pumps, and one single-stage impulse turbine. Inter-propellant seal(IPS) is located between the LOX pump and the kerosene pump to avoid any interaction between the propellants. A series of component and TPU(Turbopump Unit) test has been completed in the level of simulant propellants and ready for hot firing tests.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.109-115
• /
• 2004

A 1-D system design program has been developed for the preliminary design of the turbopump system in liquid rocket engines, which use LOx and kerosene as propellants. Gasgenerator cycle and staged combustion cycle were considered as turbopump type liquid rocket engine systems. In the system analysis, mass flow balance, thrust, specific impulse, mixture ratios, turbopump power, and turbine expansion ratio of engine system were analyzed. Results show that most of the parameters agree well with real engine parameters except gasgenerator. Therefore, the l-D system design program developed in this study can be used to derive the preliminary design parameters of a turbopump with any thrust level liquid rocket engine.

• Aerospace Engineering and Technology
• /
• v.2 no.2
• /
• pp.151-156
• /
• 2003

Liquid rocket engine system is classified into an engine of pressurization and turbo pump type by the way of fuel fed-supporting system. In the KSR-III sounding rocket, an engine of pressurization type was used, but there was lots of technical problems to be solved for a use as the first stage engine of space launch vehicle. So, an engine of turbo pump type was required to be developed to overcome the technical limitation of liquid rocket engine. In this research, the analysis of propellant of Kerosine-LOX and methane-LOX which are noticed as a future propellant was carried out for the purpose of studying the basic characteristics. And to review the basic characteristics of an engine of turbo pump type, among the sizing variant of the space launch vehicle, the ways of injecting a satellite to a direct orbit and transient orbit were discussed in this paper.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.56-61
• /
• 2011

Performance test of a full-scale turbopump assembly for a 75 ton class liquid rocket engine was carried out at full speed. Model fluid was used as a working medium: liquid nitrogen for the oxidizer pump, water for the fuel pump, and hot air for the turbine. The turbopump was operated stably, satisfying the performance requirements. Head coefficient and flow coefficient of the pumps remained constant at the speed-increasing period. In terms of performance characteristics of pumps and turbine, the results from the turbopump assembly test showed a good agreement with those from the turbopump component tests.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.91-100
• /
• 2016

Efficiency characteristics of centrifugal turbopumps for a liquid rocket engine were investigated. Predicting the performance of pumps for a turbopump assembly test, the variation on pump efficiency by working fluids was analyzed from pump component tests. Water and liquid nitrogen (LN2) were used for the component test, kerosene (Jet A-1) and liquid oxygen (LOX) were adapted for the turbopump assembly (TPU) test as working fluids. Overall performance of the pumps was investigated covering design/off-design operating points and the pump efficiency on the environment of real media (LOX/kerosene) could be modified from the pump component tests.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.27-32
• /
• 2010

Performance test of a full-scale turbopump assembly for a 75 ton class liquid rocket engine was carried out at full speed. Model fluid was used as a working medium: liquid nitrogen for the oxidizer pump, water for the fuel pump, and hot air for the turbine. The turbopump was operated stably, satisfying the performance requirements. Head coefficient and flow coefficient of the pumps remained constant at the speed-increasing period. In terms of performance characteristics of pumps and turbine, the results from the turbopump assembly test showed a good agreement with those from the turbopump component tests.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.1
• /
• pp.64-70
• /
• 2007

A test facility was developed where an inducer for a liquid rocket engine turbopump can be tested using liquid nitrogen as a working fluid. At the facility, a hydrodynamic performance test and a cavitation performance test for an oxidizer turbopump were carried out. Head-flow relation at liquid nitrogen test was similar to the case at water test. However, cavitation performance at the liquid nitrogen was superior to the case at water test, which results from the thermodynamic effect of cavitation.