• Journal of the Korean GEO-environmental Society
• /
• v.11 no.8
• /
• pp.5-14
• /
• 2010

Recent researches on the behavior of gravelly soils have been focused mainly on the relative density or on the gravel content. And some researchers presented the liquefaction behavior based on the relative density whereas others based on the gravel content of gravelly soil. However the relative densities vary with gravel content and relative density is not enough to fully express the behavior of gravelly soils. Therefore in this research state parameter which considers void ratio and effective confining pressure is introduced and Steady State Line(SSL) of gravelly soils for various gravel content are determined by undrained triaxial tests in order to express the behavior of gravelly soils. From the research the position of SSL moved downward with gravel content. And the same density of soil showed dense sand behavior or loose sand behavior depending upon the confining pressure. Especially relative density 80% of gravelly soil showed loose sand behavior under high confining pressure. However the gravelly soils with similar state parameters showed similar stress behaviors. It can bee seen that state parameter is useful tool to evaluate undrained behavior of gravelly soils. Also state parameter and undrained strength showed good correlations.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.303-309
• /
• 2009

The effects of zeolite type catalysts addition on the thermal decomposition of low density polyethylene(LDPE) and ethylene vinyl acetate(EVA) resin have been studied in a thermal analyzer(TGA, DSC) and a small batch reactor. The zeolite type catalysts tested were natural zeolite, FCC catalyst, used FCC catalyst, and catalyst A. As the results of TGA experiments, addition of antifogging-agent decreased the pyrolysis point to $250^{\circ}C$, but addition of longevity-agent and clay reduced the pyrolysis rate in EVA resin. Addition of the zeolite type catalysts in the LDPE resin increased the pyrolysis rate in the order of catalyst A > used FCC catalyst > natural zeolite > LDPE resin. Addition of the zeolite type catalysts in the EVA resin increased the pyrolysis rate in the order of used FCC catalyst > natural zeolite > catalyst A > EVA resin. In the DSC experiments for LDPE resin, addition of zeolite type catalysts decreased the melting point and the heat of pyrolysis reaction in the order of catalyst A > used FCC catalyst > natural zeolite> LDPE resin. In the batch system experiments, the mixing of natural zeolite enhanced the yield of liquid fuel oil.

• Journal of the Mineralogical Society of Korea
• /
• v.18 no.2
• /
• pp.127-134
• /
• 2005

Although the bulk composition of materials is one of the major considerations in extractive metallurgy and environmental science, surface composition and topography control surface reactivity, and consequently play a major role in determining metallurgical phenomena and pollution by heavy metals and organics. An understanding of interaction mechanisms of different chemical species at the mineral surface in an aqueous media is very important in natural environment and metallurgical processing. X-ray photoelectron spectroscopy (XPS) has been used as an ex-situ analytical technique, but the material to be analyzed can be any size from $100\;{\mu}m$ up to about 1 cm. It can also measure mixed solids powders, but it is impossible to ascertain the original source of resulting x-ray signals where they were emitted from, since it radiates and scans the macro sample surface area. The study demonstrated the ability of TOF-SIMS to detect individual organic species on the surfaces of mineral particles from plant samples and showed that the TOF-SIMS techniques provides an excellent tool for establishing the surface compositions of mineral grains and relative concentrations of chemicals on mineral species.

• Korean Journal of Food Science and Technology
• /
• v.42 no.1
• /
• pp.97-102
• /
• 2010

Curcuminoids are polyphenolic compounds and include curcumin and its derivatives possessing a yellow color. In the present study, changes in the chemical stability and antioxidant activities of curcuminoids, including curcumin, demethoxycurcumin (DMC), and bisdemethoxycurcumin (BMC), were investigated under various processing conditions. The yellowness of a mixture of the curcuminoids (79.4% curcumin, 16.8% DMC, and 3.8% BMC) at 405 nm was proportional to their amounts analyzed by HPLC. The curcuminoids became less stable with increases of pH and temperature during storage. Exposing a solution of the curcuminoids to autoclave conditions ($121^{\circ}C$, 1.2 atm for 15 min) decreased residual curcuminoid levels by 80-90%; however, as a powder under the same conditions the curcuminoids were much more stable with less than 10% loss. After autoclave treatment, scavenging activities of the curcuminoids for DPPH and ABTS radicals were reduced by 10.3 and 33.4%, respectively, whereas nitric oxide scavenging activity was slightly increased. The residual levels of curcumin, DMC, and BMC after autoclaving were 0.7, 1.4, and 0.9%, respectively, indicating that curcumin was the most sensitive to autoclave treatment. The results indicate that under processing conditions, pH and temperature markedly affect the stability of curcuminoids and major losses of curcuminoids occur after autoclaving. These conditions should be considered when processing foods containing curcuminoids.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.1
• /
• pp.8-15
• /
• 1998

The catalytic hydrogenation of carbon dioxide has been studied for the fixation of carbon dioxide to mitigate global warming problems, but it needed hydrogen, which the price is still high. Recently, the electrochemical reduction of carbon dioxide has been drawn attractions because carbon dioxide could be converted to the valuable chemicals such as methane, ethane and alcohols electrochemically in the electrolyte solution using a catalytic electrode. This system is simple because the water electrolysis and hydrogenation take place at the same time using the surplus electricity at midnight. In this work, a continuous electrochemical reduction system was fabricated, which was composed of the reduction electrode (copper or perovskite type, $2{\times}2cm^2$), reference electrode(platinum, $2{\times}6cm^2$), standard electrode(Ag/AgCl), and potassium bicarbonate electrolyte solution saturated with carbon dioxide. The quality and quantity of the products and reduction current were analyzed, according to the electrolyte concentration and electrode type.

• The Journal of the Petrological Society of Korea
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2013

Physical properties, XRF, UV-Vis, FTIR studies were carried out in order to characterize gemological features of ruby from Tajikistan. Fluorescence reaction of the Tajikistan ruby to short wave ultraviolet was moderate to very strong in red and long wave ultraviolet rays was weakly detected. UV-visible analysis strong absorption bands at 468.5, 475, 476.5 nm and broaden bands at 550 nm were observed for ruby due to $Cr^{3+}$. According to FT-IR analysis, all rubies from Tajikistan showed the similar patterns and kaolinite peaks at 3500, 3617, 3630, $3677cm^{-1}$ and boehmite broaden absorption bands at 3085 and $3320cm^{-1}$. Inclusions in Tajikistan ruby are observed solid inclusions, negative crystals, needle and silk inclusions. These distinctive characteristics mentioned above can be used to identify the locality and source of ruby stones from Tajikistan.

• Economic and Environmental Geology
• /
• v.32 no.6
• /
• pp.561-573
• /
• 1999

Mesothermal gold deposits of the Heungdeok, Daewon and Ilsaeng mines in the Youngdong area occur in fault shear zones in Precambrian metamorphic rocks of central Sobaegsan Massif, Korea, and formed in single stage of massive quartz veins (0.3 to 3 m thick). Ore mineralogy is simple, consisting dominantly of pyrrhotite, sphalerite and galena with subordinate pyrite, chalcopyrite, electrum, tetrahedrite and native bismuth. Fluid inclusion data indicate that hydrothermal mineralization occurred at high temperatures (>240$^{\circ}$ to 400$^{\circ}$C) from $H_{2}O-CO_{2}(-CH_{4})$-NaCI fluids with salinities less than 12 wt. % equiv. NaC!. Fluid inclusions in vein quartz comprise two main types. These are, in decreasing order of abundance, type I (aqueous liquid-rich) and type II (carbonic). Volumetric proportion of the carbonic phase in type II inclusions varies widely in a single quartz grain. Estimated $CH_4$ contents in the carbonic phase of type II inclusions are 2 to 20 mole %. Relationship between homogenization temperature and salinity of fluid inclusions suggests a complex history of fluid evolution, comprising the early fluid's unmixing accompanying $CO_2$ effervescence and later cooling. Estimated pressures of vein filling are at least 2 kbars. The ore mineralization formed from a magmatic fluid with the ${\delta}^{34}S_{{\Sigma}S}$, ${\delta}^{18}O_{water}$ and ${\delta}D_{water}$ values of -2.1 to 2.2$\textperthousand$, 4.7 to 9.3$\textperthousand$ and -63 to -79$\textperthousand$, respectively. This study validates the application of a magmatic model for the genesis of mesothermal gold deposits in Youngdong area.

• Korean Journal of Materials Research
• /
• v.4 no.5
• /
• pp.600-607
• /
• 1994

Optimum exper~mental conditions were established for the growth of heteroepitaxial GaAs layers on InP using liquid phase epitaxy (LPE) technique. Results showed that the optimum growth temperature was $720^{\circ}C$ at a cooling rate of $0.5^{\circ}C$/min. Surface morphology of the grown layers significantly improved by addition of about 0.005wt% Se to the Ga growth melt, which effectively suppressed melt-back of InP substrates into the melt during the initial stage of growth. It was observed that the quality of GaAs layers also improved substantially when the substrates patterned with grating structure were used, as determined by the (400) double crystal X-ray diffraction. The transmission electron microscopy observation indicated t.hat the misfit dislocations interact with each other at the grating region, resulting in a lower dislocation density in the upper GaAs layer.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.1
• /
• pp.51-60
• /
• 2011

Electrical resistivity is applied for understanding details about layers and obtaining basic properties of soils to various measurement devices. The objective of this study is development of TRP(Temperature-compensated Resistivity Probe), analysis about effects of temperature changes during cone penetration test, and observation of characteristics of cone penetration. In order to observation of temperature changes according to a diameter difference of resistivity cone probe, the cone which has wedge type cone tip is made to two types, 2mm and 5mm. Temperature sensor is attached at 15mm below from cone tip because of an electrical interference with elecrical resistance probe. Delectrical connector is used to prevent electric disturbance between motor type penetrating machine and electrical resistivity cone probe. Application tests are carried out in acrylic cell whose diameter is 30cm with uniform Jumunjin sand according to densification caused by blows. The test results indicate that the temperature is increased uniformly during penetration and a tendency, characteristics of cone penetration, is discovered during altering state of soils. This study suggests that the temperature effects and characteristics of penetration should be considered in penetrating tests in order to conduct an accurate ground investigation using TRP(Temperature-compensated Resistivity Probe).

• Korean Journal of Food Science and Technology
• /
• v.42 no.3
• /
• pp.287-291
• /
• 2010

In this study, a simple and rapid pre-treatment method based on liquid extraction was applied for the simultaneous determination of three macrolides (spiramycin, tylosin, and tilmicosin) residues. In these studies, the stock farm products was used as a matrix sample. When the liquid extraction method was compared with the solid phase extraction (SPE) method, the former showed higher recovery percentages and simpler steps than the latter. The macrolids were separated using a reverse-phase C18 ($250\;mm{\times}4.6\;mm$, $5\;{\mu}m$) column and a gradient elution with mobile phases consisting of phosphate buffer (pH 2.5) and acetonitrile. Tylosin and tilmicosin were detected at 288 nm and spiramycin was detected at 232 nm. The average recovery percentage ranged between 83.0-90.2% for samples spiked with the three macrolids at 50 and 100 ng/g The validation results showed that the limit of detection (7 (spiramycin), 12 (tilmiconsin), 12 (tylosin) ng/g)) was under the regulatory tolerances and the linearity from calibration curves was satisfactory for determining the multi-residue of three macrolids in farm products. Monitoring samples were collected at the main cities in Korea as Seoul, Busan, Deajeon, Incheon, Deagu, and Gwangju. Microlide antibiotics were not detected in most samples.