• Journal of the Korean GEO-environmental Society
• /
• v.4 no.2
• /
• pp.65-76
• /
• 2003

Stone column is a soil improvement method and can be applicable for loose sand or weak cohesive soil. Since the lack of sand, stone column seems one of the most adaptable approach for poor ground as a soil improvement technique. However, this method was not studied for practical application. In this paper, the bearing capacity of single stone column at the Gaduk, Ulsan and Gwangyang under the bulging and general shear failure mode were compared with those of the suggested formulas. Especially, a test result of single stone column at the Busan area by static load was compared with the bearing capacity of suggested formulas. The analysis results showed that there were not much bearing capacity differences among those suggested bearing capacity formulas. However, the bearing capacity by static load test was almost double of those with suggested formula. The result also showed that the undrained shear strength was the most important parameter for the bearing capacity estimation of stone column.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.12
• /
• pp.1013-1019
• /
• 2014

Solid-liquid Phase Change Material(PCM) as a thermal control hardware for the electro-optical payload of low earth orbit satellite is numerically studied which can be substituted with Thermal Buffer Mass(TBM). The electro-optical module in LEO satellite is periodically work and high heat is dissipated during the imaging period, however, the design temperature range is very tight and sensitive. In order to handle this problem TBM is added and as a result the time constant of the module temperature increases. TBM is made of Al6010 and its mass directly affects the system design. To save the mass PCM is suggested in this study. The latent heat of melting or solidification is very high and small amount of PCM can play a role instead of TBM. The result shows that only 12% of TBM mass is enough to control the module temperature using PCM.

• KSBB Journal
• /
• v.21 no.4
• /
• pp.255-259
• /
• 2006

The biodegradable hyaluronic acid(HA) membranes cross-linked with lactide using the crosslinking agent, 1-ethyl-3(3-dimethyl aminopropyl) carbodiimide(EDC) were prepared as a potential biocompatible material for tissue engineering. HA membranes having different mechanical properties were synthesised by varying degree of the mole ratio of lactide to HA, EDC concentration, and crosslinking temperature. HA membranes were degradable in water solution and the degradation became slower with the increasing mole ratio of lactide to HA. HA membranes were sterilized using ethylene oxide gas and extracted with cell culture medium for 24 h at $37^{\circ}C$ and 200 rpm. Cytotoxicity of the extract was tested using NIH/3T3 mouse embryo fibroblast as a model cell. Growth inhibition was not observed in the extracts of HA membranes with the mole ratios of lactide to HA, 5 or 10, and 10% EDC concentration, however 11% of growth inhibition was observed in the extract with the mole ratio of 13. Growth inhibition was not observed in the extracts of HA membranes prepared with 5% EDC or 10% EDC and the mole ratio of lactide to HA, 10, however 12% of growth inhibition was observed in the extract with 20% EDC. Cytotoxicity was not observed in the extracts of HA membranes prepared at varying crosslinking temperatures, $15^{\circ}C,\;25^{\circ}C,\;and\;28^{\circ}C$ with the mole ratio of lactide to HA, 10 and 10% EDC.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.29-29
• /
• 2002

공구강 등 산업용 재료로 널리 사용되는 카바이드 계 재료는 입자 크기 및 분포에 따라 기계적 성질이 변화하므로, 이를 제어하고 조절하는 기술에 관하여 많은 연구가 진행되어 왔다. 본 연구에서는 TiCN-WC-Co 복합초경계 에서 소결 공정 및 조성변화에 따른 입자 모양을 관찰하고 이에 따른 업자 성장 거동을 고찰하였다. 일반적으로 입자 조대화 양상과 고상 입자의 모양과는 밀접한 관계가 있다. 각진 입자의 경우에 는 계면이 원자적으로 singular 하여 원자의 홉착이 어렵기 때문에 임계값 이상의 성장 구동력을 받 는 몇몇 입자만 성장하는 비정상 입자 성장이 일어날 수 있다. 반면에 계면이 rough한 퉁큰 엽자의 경우에는 원자 홉착에 필요한 구동력이 존재하지 않아 성장 구동력을 받는 모든 입자들이 성장하기 때문에 정상 입자 성장을 하게 된다. 이와 같이 입자 모양에 따른 입자 성장 거동은 전체 미세구조를 결정하게 되며, 이에 따른 물리 화학적 물성을 변화시킨다. 이러한 입자 성장 원리를 적용하 면 복합초경계 (TiCN-WC-Co)에서도 입자성장이 억제되고 치밀한 소결체를 제조할 수 있을 것이다. 본 실험에서는 평균입도가 각각 0.1, 1.33, 2$\mu\textrm{m}$인 TiCN, WC, Co 분말을 사용하여 $((I00_{-x)}TiCN+_xWC)-30Co$ (wt%) 조성에서 TiCN/WC 비를 변화시키면서 업자 모양과 입자성장 거동을 관찰하였다. 청량된 분말은 WC 초경 볼로 밀렁하고, 건조한 후, 100 mesh 체로 조립화 하였다. 이 분말을 100 MPa의 압력으로 냉간정수압성형 하고 $10^{-2}$ torr의 진공분위기의 graphite f furnace에서 carbon black으로 packing 하여 액상형성 온도 이상에서 소결하였다. 소결된 시편은 경면 연마하여 주사전자현미경으로 미세 조직을 관찰하였다. TiCN-30Co 조성 시편은 corner-round 모양의 입자 모양으로 소결 시간 증가에 따라 빠른 입자 성장을 나타내었다 .(7STiCN+2SWC)-30Co 조성 시변의 경우 일반적으로 보고된 바와 같이 core/shell 구조를 나타내었으며, core는 TiC-rich 상이었고, shell은 (Ti,W)(C,N) 복합 탄화물 상이었다. WC 함량이 중가함에 따라 입자의 corner-round 영역이 증가하였으며 (SOTiCN-SOWC)-30Co 조성 근처에서는 거의 둥근 형태의 입자 모양을 나타내었다. 또한 TiCN - 30Co 조성 시편에 비하여 WC가 첨가된 시펀들은 작은 평균입자크기를 나타내었다. 본 연구의 결과는 shell 영역 조성 변화는 계면에너지 이방성과 기지상 내의 펑형 입자 모양을 변화시키고 나아가 입자 성장 속도 에도 영향을 미친다는 것을 보여준다.

• Applied Microscopy
• /
• v.39 no.1
• /
• pp.65-72
• /
• 2009

Cryo-SEM which enables specimens to be observed in frozen form has been used to study liquid specimens in their native states. Cryo-methods, sample preparation for cryo-SEM, are quite complex and involve several discrete but vitally interconnected steps which are rapid cooling, fracturing, sectioning, etching and coating. It is important to select practical techniques and to optimize conditions of each steps considering analytic purpose and specimen characters, viz., sample dimension, water contents. In this study, etching methods and sample preparation before freezing had been studied for observation of cyanobacteria, Synechocystis sp. PCC 6803 using cryo-SEM and their cryo-SEM images were compared to Conventional SEM (CSEM) images treated by chemical fixation. We could observe the improved morphological images of the pili of the surface and membranes of Synechocystis sp. PCC 6803 and the three-dimensional architectures of their biofilm, which were difficult to observe using chemical fixation and CSEM. These results suggest that cryo-methods/cryo-SEM are useful techniques for morphological study of biological specimen.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.36 no.3
• /
• pp.167-174
• /
• 2010

The hair nourisher products are used for prevention of hair loss and classified as quasi-drug in Korea. As concerns about hair loss has been increased, the demand for hair nourisher products has been growing. It is difficult to analyze their main ingredients because they contain various ingredients including natural plant extracts, vitamins, preservatives and exfoliators. The purpose of this study was to develop and validate simultaneous analytical methods of active ingredients in hair nourisher products such as nicotinamide, tocopherol, salicylic acid, dexpanthenol and benzyl nicotinate by HPLC. The active ingredients were separated on a $C_{18}$ column by using acetonitrile/phosphate buffer as a mobile phase, and detected at UV 220, 270 and 300 nm. The calibration curve showed linearity in the range of $12.5{\sim}800\;{\mu}g/mL$ and the recoveries were 97.3 ~ 103.5 % (RSD 0.9 ~ 2.8 %) in liquid matrix and 101.9 ~ 115.9 % (RSD 0.7 ~ 7.7 %) in shampoo matrix. Validated method was applied to hair nourisher products obtained from distribution market. Fortunately, all samples met their criteria. This study might be expected to provide the method for determining active ingredients in hair nourisher products and lead to promote a rapid market entry.

• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.121-127
• /
• 2011

In this study, possible use of indigenous natural loess (Hwangtoh) as a new binding material via geopolymerization process is examined. Hwangtoh pastes with four different mix proportions of varying alkali liquid concentrations (6 M, 8 M) and the constituents of the binder as well as the alkali liquid at a constant liquid-to-binder ratio of 0.55 were prepared. Analysis of the natural loess (Hwangtoh) paste was carried out as follows : 1) Measurement of compressive strength and weight of cubic specimens versus curing time; 2) Analysis by X-ray diffraction (XRD) and scanning electron microscope (SEM) about reaction product; 3) Porosity analysis of hardened Hwangtoh paste. The result showed that it is possible to prepare Hwangtoh paste with 29.1 MPa at the age of 7 day by using alkali solution (made as 1 : 4.5 the mass ratio of liquefied $Na_2SiO_3$ and NaOH solution and applying the curing temperature of $60^{\circ}C$). Compressive strength development with respect to the degree of moisture evaporation from the paste seems to be independent of curing temperature. Therefore, it seems that higher early strength of the paste specimens cured at higher temperature can be attributed to both higher rate of reaction and moisture evaporation.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1115-1122
• /
• 2001

The tendency of the miximum brightness of $Y_2$O$_3$:Eu phosphor with various activator concentration, by different surface treatment methods as well as different exciting energies were investigated. The surface treatment methods were the adsorption method used $\alpha$-Fe$_2$O$_3$powder prepared emulsion-drying process and the precipitation method used FeSO$_4$/ethanol. Eu concentration of maximum brightness of $Y_2$O$_3$:Eu phosphor prepared by solid-solid state was changed with various exciting energies. The concentrations were 0.02 mol at VUV(147 nm) as well as 400 V and 0.03 mol at 5 kV. The phosphor treated both by adsorption method and precipitation method showed decreasing luminescent intensity with increasing amount of $\alpha$-Fe$_2$O$_3$, and the methods are chosen by exciting energy. Adsorption method was effective in a low voltage and VUV(147nm) region, and precipitation method was effective in the high voltage region.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.304-309
• /
• 2012

Size verification of small and large bubbles in a bubble column was investigated by employing the dynamic gas disengagement (DGD) method and dual electrical resistivity probe (DRP) method, simultancously. The holdups of large and small bubbles in the bubble column in a given operating condition were obtained by means of the DGD method by measuring the pressure drop variation in the column with a variation of time after stopping the gas input into the column. The size and frequency of bubbles were measured by the DRP method in the same operating condition, from which the bubble holdup of each range of size was obtained. The verification of size in determining the large or small bubbles was decided by comparing the holdups of large or small bubbles measured by the DGD method with that measured by the DRP method. Filtered compressed air and tap water were used as a gas and a continuous liquid medium. The diameter and height of the bubble column were 0.102 m and 1.5 m, respectively. The demarcation size between the large and the small bubbles in the bubble column was 4.0~5.0 mm; the demarcation size was about 5.0 mm when the gas velocity was in the relatively low range, but about 4.0 mm when the gas velocity was in the relatively high range, within this experimental conditions.

• Clean Technology
• /
• v.22 no.4
• /
• pp.274-280
• /
• 2016

In this study, it was to develop a chemical method that can recycle the cutting oil which accounts for about 25% of the cost of the process among containing materials of silicon waste sludge generated in the process for producing a solar cell wafer. The 7 types of reagents have been used, including acetone, HCl, NaOH, KOH, $Na_2CO_3$, HF, $CH_2Cl_2$, etc. for this experiment. And It was carried out at a speed of 3000 rpm for 60 minutes centrifugation after performing a reaction with a waste sludge at various concentrations. As a result, the best reagents and conditions for separating the solid such as a silicon powder and a metal powder and liquid cutting oil were identified as 0.3 N NaOH. It is found to be pH 6.05 in a post-processing recycled cutting oil with 0.3 N NaOH after reaction of waste sludge and 0.1 N HCl which is effective to remove metal powder in order to adjust the pH to suit the properties of the weak acid is a commercially available cutting oil and it showed excellent turbidity than when applied to sludge with 0.3 N NaOH alone. The results of FT-IR analysis which can compare the properties of the commercially available cutting oil shows it has a possibility of recycling oil. The cutting oil recovery rate obtained through the experiment was found to be 86.9%.