• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.29-34
• /
• 2017

In this paper, we report a method of improving the productivity of lead wire fabricated through the rolling process by increasing its linear velocity. The most important point to consider when raising the linear velocity is that the original specifications must still be adhered to. In other words, the dimensional tolerance must be satisfied when increasing the linear velocity of the wire without causing cracks. However, if the linear velocity of the wire is increased, the degree of reduction must also be increased, which causes more damage to the wire and increases the load on its surface. Therefore, we studied a three step rolling process which can satisfy the specifications of the wire produced through the two step rolling process and improve the productivity. In this study, only the roll gap of the three-stage rolling roller is assumed to be a variable, while the other conditions are the same as the field conditions. In addition, through the PIANO (Process Integration, Design and Optimization) tool, the (optimum?) surface roughness and maximum stress are maintained.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.35-38
• /
• 2004

In general, tube drawing process is composed of two steps, so called first drawing and second drawing. Drawing cracks are mainly occurred during the 2nd drawing process due to the improper drawing process. In order to analyze the reduction distribution in successive two-step drawing process, tube drawing process was simulated by finite element method. From the finite element analysis, the balance between first and second reduction is proved to be important factor to prevent drawing cracks. Hence the numerical expression was developed for tube drawing process to distribute even strain and criteria curves that can predict the safe drawing region were also proposed using this numerical formula.

• The korean journal of orthodontics
• /
• v.38 no.1
• /
• pp.31-40
• /
• 2008

Objective: This study investigated the skeletal and dentoalveolar changes after intrusion of maxillary posterior teeth using miniscrew implants during the treatment and posttreatment period. Method: The subjects consisted of 11 adults (1 male, 10 females) whose open bites were treated by posterior teeth intrusion with miniscrew. The lateral cephalometric x-rays of pre-treatment, post-treatment, and the retention period were evaluated. Results: The average intrusion of maxillary posterior teeth at the end of the treatment period was 2.22 mm (p < 0.001) and the average extrusion of maxillary posterior teeth at the end of the 17.4 month retention period was 0.23 mm (p = 0.359). The relapse rate was calculated at 10.36%. A decrease in overbite after the 17.4 month retention period was 0.99 mm (p < 0.05). The relapse rate was calculated at 18.10%. The skeletal changes and vertical height change of maxillary posterior teeth during the retention period was statistically insignificant, but there was a significant decrease in overbite (mean 0.99 mm, p < 0.05). The amount of intrusion and the overbite improvement from treatment significantly correlates to the degree of relapse. Conclusions: The results indicate that intrusion of the maxillary posterior teeth using miniscrews is an effective, non-surgical treatment modality which can reasonably be used to address adult open bite.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.11
• /
• pp.1279-1287
• /
• 2011

Weather strip is a functional component of a car body and doors for leaking protection, isolating outside noise and vibration reduction. Insert metal inserted to the weather strip plays a key role to keep the shape of the weather strip and increase its strength. Insert metal is mainly produced by a press process, which has low productivity and 40% material loss due to the scraps. To solve the problems, a high-speed rolling process for manufacturing the insert metal of weather strip is being attempted. In this study, the insert metal is manufactured by a high-speed rolling process, and its process variables: reduction, relative velocity of rollers and the number of passes, are optimized by using the FEA and the actual tests. The prototype was manufactured by the optimal process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.271-274
• /
• 2009

This paper deals with an evaluation of the product quality according to intermesh of the roller straightening process of a steel cord. To perform the experiments, a single-layered steel cord with three wires is selected as a target. Intermeshes at inlet and outlet of the roller straightening device are selected as a respective design parameter. According to two intermeshes of the roller straightening device, a design table is generated and experiments were performed. Three assessment items of the product quality, such as the residual torsion, the arc-height and the pre-forming ratio, are measured in each experimental case for the quantitative evaluation of a steel cord. Based on the measured data, the sensitivity of two intermeshes was analyzed and the prediction equation for the product quality of a steel cord was also constructed from the regression analysis.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.31 no.4
• /
• pp.378-386
• /
• 2015

Overdenture has the advantage of improving the stability and retention of the denture but the abutment may be easily affected by caries or periodontal disease and the thin denture can be easily broken. The magnetic attachment overdenture has a high vertical retention but a low horizontal retention, thus, exerting a less disruptive force to the abutment or implant and shows less abrasion or damage compared to other mechanical retainers. Denture fractures in overdenture is caused by the thin denture base as the attachment is inserted, but it may also be caused by the difference in detrusion between soft tissue and hard tissue, and between an implant and a natural tooth. To compensate this shortcoming, a magnetic attachment with a silicone ball inserted in the magnet was developed as we report a successful case using this specific type of magnetic attachment overdenture.

• The korean journal of orthodontics
• /
• v.34 no.1 s.102
• /
• pp.13-21
• /
• 2004

Recently several techniques have been reported for the treatment of anterior open bite in adults characterized by molar intrusion with skeletal anchorage. In this study, five adult patients who had anterior open bite malocclusion were selected to undergo upper molar intrusion with midpalatal miniscrew to close the open bite. The aim of this study is (1) to validate true intrusion of molars in adults (2) to test the usefullness of midpalatal miniscrews as anchorage for intruding upper molars (3) to evaluate the skeletal and dental changes of open bite closure. The results are as follows. (1) All had true intrusion of the maxillary molars. Mean amount of molar intrusion was 3.4mm(range 1.5-5mm). (2) No movement of midpalatal miniscrew occurred during their use. (3) Open bite closure was achieved for all 5 patients. The mandible closed and B-point rotated anteriorly and upward. The mandibular plane angle and the occlusal plane angle decreased.

• The korean journal of orthodontics
• /
• v.39 no.1
• /
• pp.43-53
• /
• 2009

Objective: The purpose of this study was to compare the difference in three dimensional tooth movement using three different wire sizes($0.018{\times}0.025-in,\;0.016{\times}0.022-in$ 0.016-in) on a NiTi scissors-bite corrector. Methods: Computed tomography(CT) images of the experimental model before and after tooth movement were taken and reconstructed into three dimensional models for superimposition. The direction and the amount of tooth movement were measured and analyzed statistically. Results: The lingual and intrusive movements of the crown of the maxillary second molar were increased as the size of the NiTi wire increased. The roots of the maxillary second metals moved buccally except for the 0.016-in group. The intrusive movement of the roots of the maxillary second molars was increased as the size of the NiTi wire increased. Due to the use of orthodontic mini-implants, anchorage loss was under 0.2 mm on average. Conclusions: The $0.018{\times}0.025-in$ NiTi wire was most effective in lingual and intrusive movement of the maxillary second molar which was in scissors-bite position. Indirect skeletal anchorage with a single orthodontic mini-implant was rigid enough to prevent anchorage loss.

• The korean journal of orthodontics
• /
• v.34 no.1 s.102
• /
• pp.33-45
• /
• 2004

The purpose of this experimental study was to determine appropriate magnitude of the Gable bends to produce maximum retraction of the anterior teeth. The Calorific Machine was used to illustrate the tooth movement in three dimension. The experimental teeth except the first premolar were embedded in the artificial alveolar bone part. In a series of experiments, the extraction space was closed using arch wires with bull loops into which the gable bends of $10^{\circ},\;20^{\circ},\;30^{\circ}$ degrees were incorporated. The experiments were repeated three times for each degree of the gable bend. Before and after the space closure, radiographs were taken in the sagittal and occlusal directions using occlusal films. Analysis of variance and Scheffe post hoc test were used to determine significant differences among the three groups. The following results were obtained. 1. As magnitudes of the gable bends increased, more bodily anterior tooth movement was seen and the distance of retraction also increased. 2. As magnitudes of the gable bends increase, the amount of posterior tooth protraction decreased while intrusive and buccal movement increased. 3. The arch was coordinated by distal-in rotation of the canine and mesial-in rotation of the second premolar adjacent to the extraction space.