• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.66-73
• /
• 2004

In this study, combustion characteristics and various performances of a Diesel fuel DI-HCCI engine using 2-stage injection method were investigated. From these researches, application ability of 2-stage injection strategy to a DI-HCCI engine was confirmed and improvement methods of performances were considered. As the results, Using 2-stage injection method, without change of engine specifications and loss of IMEP, exhaust of NOx and Smoke emissions could be reduced to about 1/3 (at 1400rpm, IMEP 6bar) compared to conventional Diesel combustion.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.80-89
• /
• 2004

In order to confront the increasing air pollution and the tightening emission restrictions, this research developed a diesel engine using DME, the advanced smoke-free alternative fuel. By numerical analysis, flow field, spray, and combustion phenomenon of the DME engine was presented. Using an experimental method, the configuration of the fuel supply system and operation/power performance was tested with the current plunger pump. Most emission performance, especially smoke performance was significantly improved. The possibility of conversion from the current diesel engine into the DME engine was affirmed in this research. However, it was found that the increase of engine RPM and fuel amount need to be properly adjusted through matching the characteristics of fuel and injector for further improvement.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.6
• /
• pp.895-904
• /
• 2011

Stratified charge has been thought as one of the ways to avoid a sharp pressure rise on HCCI combustion. The purpose of this study is to evaluate the potential of stratified charge for reducing PRR on HCCI combustion. The pre-mixture with thermal, mixing and EGR stratifications is charged in Rapid Compression Machine. After that, the pre-mixture is compressed and in that process, in-cylinder gas pressure and temperature are analyzed. Additionally numerical calculation with multi-zones modeling is run to know the potential of stratified charge for reducing PRR.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3044-3048
• /
• 2008

It is well known that Premixed Charge Compression Ignition (PCCI) diesel engines according to many technologies such a change in injection timing, multiple injection strategy, cooled EGR, intake charging and SCV have the potential to achieve homogeneous mixture in the cylinder which result in lower NOx and PM as well as performance improvements. This may generate merely the infinite number of experimental conditions. The use of Response Surface Methodology (RSM) technique can considerably pull down the number of experimental set and time demand. This paper presents the effects of both fuel injection and engine operation conditions on the combustion and emissions in the PCCI diesel engine system. The experimental results have revealed that a change in fuel injection timing and multiple injection strategy along with various operating conditions affect the combustion, emissions and BSFC characteristics in the PCCI engine.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.25-28
• /
• 2013

This study presents both experimental and numerical investigation of ignition characteristics of n-heptane and n-butanol mixture. The $O_2$ concentration was fixed to 9-10% to make high exhaust gas recirculation(EGR) rate condition. Experiments were performed using a rapid compression machine. In addition, a numerical study of the ignition delay time was performed using CHEMKIN codes to validate experimental results and predict chemical species after combustion process. The results showed that the ignition delay time increased with increasing n-butanol ratio and the reactivity decreased by low $O_2$ concentration.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.29-31
• /
• 2013

In this study, the characteristics of particulate matters (PM) from diesel and biodiesel fuel combustion was experimentally investigated. The experiment was performed in a single cylinder common-rail compression ignition engine. The fuels were injected at -5 CAD (Crank angle degree) ATDC (After top dead center) with 80 MPa injection pressure. Size distribution of PM was measured by scanning mobility particle sizer (SMPS) and morphology of PM was studied by transmission electron microscopy (TEM). PM from biodiesel shows lower emission level and smaller primary particles.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.33-35
• /
• 2013

The present work is an experimental investigation on potential operating range using directly injected gasoline fuel in a single-cylinder compression ignition (CI) engine. The objectives of present study were to apply auto-ignited combustion to gasoline fuel and to evaluate potential operating range. In order to auto-ignite gasoline fuel in CI engine, the fuel direct-injection system and the intake air system were modified that a flow rate and temperature of intake air were regulated. The heat-release rate (HRR), net indicated mean effective pressure (IMEP), start of combustion (SOC), and combustion duration were derived from in-cylinder pressure data in a test engine, which has 373.33cc displacement volume and 17.8 compression ratio. The exhaust emission characteristics were obtained emission gas analyzer and smoke meter on the exhaust line system.

• Journal of ILASS-Korea
• /
• v.23 no.4
• /
• pp.169-174
• /
• 2018

In this work, optimization of blade shape for the improvement of mixture formation and vortex of intake port was performed by numerically, and the combustion performance of CI engine with optimized blade shape was investigated. To achieve this, 3 types of blade shape were studied under the different air flow mass conditions and the numerical results were investigated in terms of humidification water, moisture concentration, and velocity distributions. Evaporated liquid mass was also compared under various test conditions to reveal the turbulent intensity in an intake port. It was observed that the optimized blade shape can improve the humidification water, moisture concentration, and velocity distributions of intake port inside. The evaporated liquid mass was also increased under the conditions with blade. Especially, low NOx emissions was observed with optimized blade condition.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.375-381
• /
• 2010

Cetane number of diesel fuel for compression ignition engine is one of main properties for fuel ignition quality. Recently the cetane index has been replaced the cetane number in order to resolve the disadvantage of CFR engine test, but these two value have slightly difference values due to addition of various additives. In this study, we analyzed the cetane number, derived cetane number and cetane index for diesel fuel which was blended with various ratios of biodiesel, kerosene and cetane improver as additives. As a result, Cetane number showed the similar value with derived cetane number, but cetane index showed quite different value with cetane number when biodiesel and cetane improver were used as additives.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.8-14
• /
• 2007

Compression ignition of homogeneous charges in IC engines indicates possibilities of achieving the high efficiency of DI diesel engines with low level of NOx and particulate emissions. The objectives of this study are to further understand the characteristics of the HCCI(Homogeneous charge compression ignition) combustion and to find ways of extending the rich HCCI operation limit in an engine-like environment. DME fuel is supplied either in the form of premixture with air or directly injected in the combustion chamber of a rapid compression and expansion machine under the conditions of various equivalence ratio and injection timing. The cylinder pressure is measured and the rate of heat release is computed from the measured pressure for the analysis of the combustion characteristics. The experimental data show that the RCEM can operate without knock on mixtures of higher equivalence ratio, when DME is directly injected in the combustion chamber than introduced as a fraction of a perfect or nearly perfect premixture. Very early fuel injection timings usually employed in HCCI operation are seen to have only insignificant effects in control of ignition timing.