• Journal of the Korean earth science society
• /
• v.41 no.5
• /
• pp.478-489
• /
• 2020

This study presents an analysis of infrasonic signals from two accidental explosions in Gwangyang city, Jeonnam Province, Korea, on December 24, 2019, recorded at 12 infrasound stations located 151-435 km away. Infrasound propagation refracted at an altitude of ~40 km owing to higher stratospheric wind in the NNW direction, resulting in favorable detection at stations in that direction. However, tropospheric phases were observed at stations located in the NE and E directions from the explosion site because of the strong west wind jet formed at ~10 km. The transmission losses on the propagation path were calculated using the effective sound velocity structure and parabolic equation modeling. Based on the losses, the observed signal amplitudes were corrected, and overpressures were estimated at the reference distance. From the overpressures, the source energy was evaluated through the overpressure-explosive charge relationship. The two explosions were found to have energies equivalent to 14 and 65 kg TNT, respectively. At the first explosion, a flying fragment forced by an explosive shock wave was observed in the air. The energy causing the flying fragment was estimated to be equivalent to 49 kg or less of TNT, obtained from the relationship between the fragment motion and overpressure. Our infrasound propagation modeling is available to constrain the source energy for remote explosions. To enhance the confidence in energy estimations, further studies are required to reflect the uncertainty of the atmospheric structure models on the estimations and to verify the relationships by various ground truth explosions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.246-246
• /
• 1999

TFT-LCD 제조공정의 발전에 따라, 박막층(a-Si, SiNx, gate 전극, ITO 등)에 대한 습식공정을 대치하는 건식식각이 선호되고 있다. scan signal의 전파지연시간을 단축시키는 장점을 갖는 Al gate 전극의 건식식각의 경우, 높은 식각속도와 slope angle의 조절, 그리고 식각균일도가 요구된다. 이러한 Al gate 전극물질로는 Al에 Ti이나 Nd와 같은 금속을 첨가하여 post annealing 동안에 발생하는 hillock을 방지하고 더불어 낮은 resistivity(<10$\mu$$\Omega$cm)와 열과 부식에 대한 높은 저항성을 얻을 수 있다. 그러나 Al-Nd alloy 박막은 식각속도와 photoresist에 대한 식각선택도가 낮아 문제로 지적되고 있다. 본 실험에서는 고밀도 플라즈마원의 일종인 자화된 고밀도 유도결합형 플라즈마를 이용하여 식각가스 조합, inductive power, bias voltage 그리고 공정압력 등의 다양한 공정변수에 따른 Al-Nd film의 기본적인 식각특성 변화를 관찰하였다. 식각시 chloring gas를 주요 식각가스로 사용하고 BCl, HBr 등을 10mTorr의 일정한 압력을 유지하는 조건하에서 첨가하였으며 inductive power는 5100W~800W, bias voltage는 -50V~-200V까지 변화를 주었다. 식각공정의 전후를 통하여 Al-Nd 박막표면의 조성변화를 관찰하기 위하여 X-ray photoelectron spectroscopy(XPS)를 이용하였으며 공정변수에 따른 식각후 profile 관찰은 scanning electron microscopy(SEM)을 통하여 관찰하였다. Al-Nd 식각속도는 100% Cl2 플라즈마에 비해 BCl3의 양이 증가할수록 증가하였으며 75%의 BCl3 gas를 첨가하였을 때 가장 높은 식각속도를 얻을 수 있었다. 또한 SEM을 이용한 표면분석으로 roughness가 감소된 공정조건을 찾을 수 있었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.6
• /
• pp.1-6
• /
• 2011

An experimental study has been conducted to scrutinize into the influence of ultrasonic standing wave field on the variation of methane/air premixed flame structure. Visualization technique utilizing the Schlieren method is employed for the observation of premixed flame propagation. The shape of flame front and local flame velocity are measured according to the variation of reactants pressure and chamber opening/closing condition. The flame fronts affected by the standing wave are clearly distorted but the vertical locations of frontal dents do not undergo any appreciable change. The influence of standing wave on the flame front becomes more prominent as the flame propagates downward. It is found that the propagation velocity of flame front with excitation of standing wave is greater than the case without the excitation. It is eventually revealed that the flame is deformed to lotus-shaped one by the vivid interaction of ultrasonic standing-wave with the reflected wave coming from the right side.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.439-444
• /
• 2003

Acoustic emission(AE) ran be very effectively applied to locate the damaged area in large structures by detecting the elastic waves generated during the damage process within solids. Source location in the composite structures has been, however, extremely difficult due to the acoustic anisotropy with the velocity dependence on fiber orientations. In this study, it has been shown that a newly proposed method for 2-D source location of anisotropic structures is practically applicable to the real structure. The method employes wave velocities obtained with different velocities from $0^{\circ}\;to\;90^{\circ}$ for a filament wound composite pressure vessel under the air-filled and the water-filled conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.5
• /
• pp.74-80
• /
• 2012

Past few years have seen the growing importance of micro shock tubes in various engineering applications like micro combution, micro propulsion, particle delivery systems. But in order to efficiently apply Micro Shock Tube to such areas require the detailed knowledge of shock characteristics and flow field inside a micro shock tube. Due to many factors such as boundary layer, low Reynolds number and high Knudsen number shock propagation inside micro shock tubes will be quite different from that of the well established macro shock tubes. In the present study, experimental studies were carried out on micro shock tubes of two diameters to investigate flow characteristics and shock propagation. Pressure values were measured at different locations inside the driven section. From the experimental values other parameters like shock velocity, shock strength were found and shock wave diagram was constructed.

• Journal of the Korean Institute of Gas
• /
• v.11 no.2 s.35
• /
• pp.65-70
• /
• 2007

The explosion phenomenon and hazard estimate of LP gas, the study was examined into variation of oxygen concentration and LP gas concentration. As the result of experiment, the lower explosive limit was decreased as the increased at concentration of LP gas and 21% of oxygen concentration. Minimum oxygen concentration was 14.5%. 12.0%, 11.5% at 1.0, 1.5 and 2.0 bar respectively. And maximum explosion pressure was increased for $6.46kg/cm^2,\;9.41kg/cm^2\;and\;13.49kg/cm^2$ according to increased of pressure. The speed of flame propagation was increased as the higher with initial pressure of LP gas.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.65-70
• /
• 2012

Experimental investigations were carried out to examine the explosion characteristics by different sizes in the wall surface shape of a water gel barrier in an explosion chamber, 1,600 mm in length with a square cross-section of $100{\times}100\;mm^2$. The sizes in the wall surface shape were varied by using water gel barriers with a cross-section of $100{\times}200\;mm^2$ and its were varied in the bottom of the chamber away 300, 700 and 1,100 mm, respectively from the closed end of the chamber. The flame propagation images were photographed with a high speed camera and the pressure was recorded using a pressure transducer and a data acquisition system. It was found that as the size of the wall surface shape increased, the flame propagation process and the time taken to reach the maximum pressure were found to be faster. As a result, both the flame speed and the explosion overpressure increased as the size of the wall surface shape increased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.60-67
• /
• 2019

To understand the low frequency instability(LFI) characteristics in hybrid rockets combustion, effects of equivalence ratio variations on the phase shift between pressure and heat release oscillations were investigated by using the direct numerical simulation. The change in the equivalence ratio of the main chamber was simulated by the temperature and composition variation of the combustion gas introduced into the post-combustion chamber. In the results, additional combustion appeared along with vortex generation at the backward step, and combustion pressure and heat release oscillations were observed as the vortex moved. In addition, the results confirmed that the phase difference between the pressure and heat release oscillation shifts because of the changes in the propagation velocity of pressure wave as the temperature of combustion gas changes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.173-181
• /
• 2014

The propagation behavior and structural variation of a premixed propane/air flame with frequency change in an ultrasonic standing wave at various equivalence ratios were experimentally investigated using Schlieren photography and pressure measurement. The propagating flame was observed in high-speed Schlieren images, allowing local flame velocities of the moving front to be analyzed in detail. The study reveals that the distorted flame front and horizontal splitting in the burnt zone are due to the ultrasonic standing wave. Vertical locations of the distortion and horizontal stripes are intimately dependent on the frequency of the ultrasonic standing wave. In addition, the propagation velocity of the flame front bounded by the standing wave is greater than that of the flame front without acoustic excitation. As expected, the influence of the ultrasonic standing wave on premixed-flame propagation becomes more prominent as the frequency increases.

• Journal of the Korean Institute of Gas
• /
• v.20 no.5
• /
• pp.40-49
• /
• 2016

When a leak occurs in the buried pipelines, The leak locations are able to detected by using the vibration sensors. These leak detection system, intended for incompressible fluid, such as water, are of using the wave propagation velocity and a signal arrival time delay between the sensors. In this paper, to develop a leak location detection system for a compressible fluid such as gas, the conventional detection methods have been studied, improved, and verified through the experiment using the compressed air. It confirmed that it is possible to detect the leak location for compressible fluid in the buried pipelines and to be applicable to the development of a leak location detection system in buried pipelines for gas.