• 한국전산유체공학회:학술대회논문집
• /
• 2002.10a
• /
• pp.23-27
• /
• 2002

천음속으로 비행하는 공기흡입유도탄의 경우, 비행거리 및 요구기동을 충족시키기 위해서는 추진제트에 의해 변화하는 기체 기미부의 압력항력을 정확히 예측하고 이 항력을 감소시키기 위한 기미부 형상설계는 매우 중요하며 필수적이다. 제트 Plume에 의한 기체 기미부 및 base의 압력분포에 따른 항력해석을 난류모델링을 고려한 수치해석 결과를 제시한다. Jet plume의 크기 및 배기가스 조건에 따른 항력변화, 및 기미부 형상에 따른 항력변화 그리고 천음속 마하수에 따른 결과 등을 제시한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.797-805
• /
• 2014

The purpose of this study was to investigate the drag and lift characteristics of the cavitator of a supercavitating underwater vehicle and the pressure loss due to water intake. These investigations were performed by changing the diameter, velocity, radius of curvature of the intake, and angle of attack of the cavitator. With increasing ratio of the intake diameter to the cavitator diameter ratio($d/D_1$), the drag coefficient and the pressure loss coefficient of the water intake decreased. The greater the increase in the ratio of the intake velocity-to-free stream velocity ratio(S), the smaller was the decrease in the drag coefficient and the lift coefficient. When the intake had a radius of curvature(c), the pressure loss coefficient decreased. On the contrary, the effect of the radius of curvature on the drag coefficient was imperceptible. For angles of attack (${\alpha}$) of the caviatator in the range of $0^{\circ}$ to $10^{\circ}$, the drag coefficient and the pressure loss coefficient changed slightly, whereas the lift coefficient increased linearly with increasing angle of attack.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3950-3960
• /
• 2014

In this study, the drag forces on a submerged square cylinder were analyzed using a three dimensional hydrodynamic model. The numerical results were compared with the experimental results to check the reliability of the numerical simulations, and the characteristics of the drag forces with the relative depths were analyzed by analyzing the pressure acting on the cylinder surface, which are normally difficult to measure experimentally. The numerical results showed that the drag forces acting on a submerged square cylinder originate mainly from the pressure forces, and component of the shear forces decreased with increasing relative depth. The pressure coefficient distributions showed that in the case of a low relative depth, a relatively high pressure was formed in the front of a cylinder, and a relatively low pressure was formed in the rear, which gives a high drag coefficient. In a high relative depth, the pressure in the front decreased and pressure in the rear increased, which is a similar phenomenon to that normally observed in two dimensional square cylinder flow. The effect of the static pressure was analyzed and the surface elevation difference between the front and rear zone of a cylinder has a limited effect on the drag forces. Finally, the numerical results showed that the drag forces acting on a submerged square are dominated by the dynamic pressure formed by three dimensional flow and the distribution of local surface elevation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.11
• /
• pp.849-859
• /
• 2020

The semi-empirical equation and commercial computational tool were used to predict the base drag of a guided missile with free-stream Mach numbers and chamber pressures, and the results were generally agree each other. Differences in flow characteristics and base drags were observed with over/under expansion conditions by the nozzle. Under the over-expansion condition, the base pressure decreased as the expansion fan was generated at upper region of the base, and base pressure decreased further with increasing free-stream Mach number as the expansion becomes strong. Under the under-expansion conditions, a shock wave was generated around the base by the influence of the nozzle flow, which increased the base pressure, and the effect increased as the chamber pressure increased. Under the same chamber pressure condition, as the free-stream Mach number increases, the characteristic that the base pressure decreases as the shock wave generated at the base moves downstream was observed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.11
• /
• pp.861-869
• /
• 2015

In this study, wall to bed heat transfer and hydrodynamic characteristics in a conical fluidized bed combustor was investigated using computational fluid dynamics method. A two-fluid Eulerian-Eulerian model was used with applying the kinetic theory for granular flow(KTGF). The effects of the two drag models, Gidaspow and the Syamlal-O'Brien model, different inlet velocities($1.4U_{mf}{\sim}4U_{mf}$) and different particle sizes on the hydrodynamics and heat transfer were studied. The results showed that the hydrodynamic characteristics such as bed expansion ratio and pressure drop were not affected significantly by the drag models. But the heat transfer coefficient was different for the two drag models, especially at lower gas inlet velocities and small particle sizes.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.10-10
• /
• 1998

천음속 익형에서 발생하는 응축충격파와 경계층의 간섭을 피동제어 하여 항력감소에 대한 연구를 2.5$\times$7$\textrm{cm}^2$ 천음속 풍동에서 수행하였다. 익형표면에 설치한 정압공으로 정압을, 익형후방에 설치한 8개의 Pitot probe로 전압을 동시에 측정하여 충격파를 통한 에너지의 손실과 항력의 변화를 계산하였고, 또한 유동장과 충격파의 형상을 가시화하기 위해 슈리렌 가시화 시스템을 사용하였다. 실험은 NACA 0012 익형에서 기공률 변화에 따른 피동제어의 항력감소 초과를 조사한 다음 NACA 64-018 익형에서는 기공률과 공동의 크기의 변화가 미치는 효과를 연구하였다. 피동제어의 개념은 충격파가 발생하는 하부벽을 다공벽으로 만들고 그 아래를 공동으로 만들면 충격파 후방의 상대적으로 높은 압력이 기류의 일부를 공동으로 자연스럽게 유입시키고 다시 공동에서 낮은 압력의 충격파 상류로 유출시키는 것이다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.58-65
• /
• 2018

To improve the performance of high-speed vehicles, various studies have been carried out on the head of vehicles. In this study, tests are conducted on flow characteristics and drag reduction using counterflow air jets in supersonic flow. The flow is visualized by the Schlieren method using a high-speed camera, and the drag is measured using a torque sensor according to the injection pressure conditions. The results of the measurements indicate that the flow changes from unsteady state to steady state for injection pressure ratios between 1.58 and 1.70, and drag reduction is observed as the pressure of the counterflow air jets increases.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.619-624
• /
• 2014

본 논문에서는 타원형 실린더 주위의 유동과 항력 및 양력 계수의 변화를 관찰하였다. EDISON_CFD를 이용하여 자유 유동(free stream)에서 타원형 실린더의 장단축 비율과 회전된 각도의 변화에 따라 실린더 후방의 유동과 압력 분포의 변화를 보고, 이에 따른 항력 계수 및 양력 계수의 변화를 시뮬레이션 하였다. 또한, 채널 유동 내에서 벽 근접에 따른 유동 변화와 항력 및 양력 계수의 변화를 관찰하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.3
• /
• pp.237-243
• /
• 2010

In this study, the effect of the shape of a pintle(obstacle) on thrust-modulation performance and drag in a pintle rocket was investigated by a cold flow test and by computational fluid dynamics. Pintle movement caused a monotonic increase in the chamber pressure. Thrust generated by the pressure distribution on the pintle body was linearly changed to the chamber pressure, and this thrust was greater than that generated by the nozzle-wall pressure distribution. Because the shock pattern in the nozzle changes with the shape of the pintle body and pressure ratio, the thrust generated by the nozzle-wall pressure is not directly affected by chamber pressure. The drag due to the pintle(obstacle) can be minimized for a fully linear pintle shape, regardless of chamber pressure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.8
• /
• pp.655-661
• /
• 2012

In this study, aerodynamic drag of a bearingless rotor hub was predicted by computational fluid dynamics methodology using unstructured overset mixed meshes. The calculated results showed that the drag due to pressure forces rather than the viscous drag act as a major factor on both the fuselage and rotor hub, and the drag acting on the torque tube accounted for the largest portion in the hub drag. It was also found the hub drag accounted for 39 ~ 41% of the fuselage drag. Finally, the result confirmed the drag of the designed rotor hub satisfied the requirement of the aerodynamic hub drag by comparing with the drag trend of developed helicopter.