• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2007.03a
• /
• pp.212-222
• /
• 2007

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2011.09a
• /
• pp.229-232
• /
• 2011

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2007.10a
• /
• pp.350-361
• /
• 2007

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2006.03a
• /
• pp.39-49
• /
• 2006

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2005.03a
• /
• pp.59-65
• /
• 2005

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2005.10a
• /
• pp.337-345
• /
• 2005

• Journal of the Korean Geotechnical Society
• /
• v.18 no.1
• /
• pp.141-152
• /
• 2002

Although a number of constitutive models have been proposed to define the behavior of geotechnical materials including elastic, plastic, and dynamic response, flew numerical models have been developed for the cyclic shear behavior of rock joints or interfaces. Such realistic constitutive models play an important role in analyzing and predicting the response of joints under dynamic loads. The purpose of this research is to verify the constitutive model modified for rough granite joints based on Disturbed State Concept(DSC) model, which has been successfully verified with respect to other materials such as dry sand-steel interface and wet sand-concrete interface. Furthermore, DSC model is compared and verified with respect to cyclic shear tests and numerical analysis results based on Plesha model. Based on the results of this research, it can be stated that DSC model is capable of characterizing the cyclic shear behavior of rough granite joints under dynamic loads.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.4
• /
• pp.659-665
• /
• 2016

The limit equilibrium method (LEM) is commonly used for slope design and stability analysis because it is easy to simulate slope and requires short calculating time. However, LEM cannot adequately simulate ploughing failure in a footwall slope with a joint set dipping parallel with slope, e.g. bedding joint set. This study performed parametric study to analyze the influence factors on ploughing failure using UDEC which is a commercial two-dimensional DEM (Distinct Element Method)-based numerical program. The influence of joint structure and properties on stability of a footwall slope against ploughing failure was investigated, and the factor of safety was estimated using the shear strength reduction method. It was found that the stability of footwall slope against ploughing failure strongly relies on dip angle of conjugate joint, and the critical bedding joint spacing and the critical length of slab triggering ploughing failure are also affected by dip angle of conjugate joint. The results obtained from this study can be used for effective slope design and construction including reinforcement.

• Tunnel and Underground Space
• /
• v.9 no.1
• /
• pp.1-11
• /
• 1999

A finite element code was developed to analyze coupled thermo-hydro-mechanical phenomena. This code is based on the finite element formulation provided by Noorishad et al. (1984) and Joint behavior was simulated Goodman's joint constitutive model. The developed code was applied for T-H-M coupling analysis for two kinds of shaft models, with a joint or without a joint respectively. For a model without a joint, temperature increased from the shaft wall to outward evidently. The radial displacement showed opposite directions of outward and inward at some distance from shaft wall. For a model with a joint, closure of joint was found due to thermal expansion. The temperature distribution along a joint showed relatively lower than that of rock matrix because of low thermal conductivity and high specific heat of water. And it could be concluded that effects of thermal flow to joint were more than that of hydraulic flow in a rock mass.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.4
• /
• pp.63-70
• /
• 2000

The quantitative analyses and the mechanical interpretation of discontinuity planes are the most important factor for the study of strength and deformation properties of rock masses containing discontinuity planes. However, the relationship between the factors investigated in the field and the actual mechanical properties of discontinuity planes is not fully understood. The main purpose of this study is to investigate the effects of density, length, and spacing of joints on elastic modulus of rock masses as these values vary. A new parameter which has a direct relation with the elastic modulus of discontinuity planes is also preposed in this study. The combination of finite element methods and homogenization methods has been used for the numerical analyses of a uintcell with discontinuity planes, which is generated using random-number generation methods. The elastic modulus of the discontinuity plane is found from the numerical analyses. The final results propose not only the relation between the investigation parameters of discontinuity planes and the elastic modulus of rock masses but also a new parameter, an effect area ratio having a linear relation with the elastic modulus of rock masses.