• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.29-32
• /
• 2002

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.738-745
• /
• 2014

In this paper, It is performing to the elastic and elasto-plastic large deformation series analysis using a numerical method for the initial deflection effect of the aluminum alloy rectangular plate in the elasto-plastic loading area patch loading size. It is assumed a boundary condition to be a simply supported condition and consider the initial deflection amplitude, aspect ratio. It examined the critical elastic buckling load and post-buckling behaviour of aluminium alloy A6082-T6 rectangular plate. It used a commercial program for the elastic and elasto-plastic deformation series analysis. If the initial deflection amplitude is smaller, the in-plane rigidity with increasing to load is reduced from the start and occurs significantly more increasing the amplitude. More higher the aspect ratio, the initial yield strength is gradually decreased, and the plate thickness thicker and occurs larger than the thin walled plate a reduction ratio of the initial yield strength of the patch loading size as 0.5.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.5
• /
• pp.542-550
• /
• 2020

The use of high-strength aluminum alloys for ships and of shore structures has many benefits compared to carbon steels. Recently, high-strength aluminum alloys have been widely used in onshore and of shore industries, and they are widely used for the side shell structures of special-purpose ships. Their use in box girders of bridge structures and in the topside of fixed platforms is also becoming more widespread. Use of aluminum material can reduce fuel consumption by reducing the weight of the composite material through a weight composition ratio of 1/3 compared to carbon steel. The characteristics of the stress strain relationship of an aluminum structure are quite different from those of a steel structure, because of the influence of the welding[process heat affected zone (HAZ). The HAZ of aluminum is much wider than that of steel owing to its higher heat conductivity. In this study, by considering the HAZ generated by metal insert gas (MIG) welding, the buckling and final strength characteristics of an aluminum reinforcing plate against longitudinal compression loads were analyzed. MIG welding reduces both the buckling and ultimate strength, and the energy dissipation rate after initial yielding is high in the range of the HAZ being 15 mm, and then the difference is small when HAZ being 25 mm or more. Therefore, it is important to review and analyze the influence of the HAZ to estimate the structural behavior of the stiffened plate to which the aluminum alloy material is applied.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2002.04a
• /
• pp.157-158
• /
• 2002

다단임팩터(cascade impactor)는 대기환경 연구에 있어 입자상물질의 물리 화학적 분석에 유용하게 사용되고 있는 입자상물질 포집장치이다. 다단임팩터의 각 단은 외벽(stage wall), 가속노즐판(acceleration nozzle plate)과 충돌판(impaction plate)으로 구성되며 충돌판에는 입자상물질의 포집을 위하여 테플론 필터, 알루미늄 필터 등을 장착하게 되어 있다. (중략)

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.3-8
• /
• 1993

본 고에서는 차체제작의 첫단계인 프레스 성형시 문제가 되는 알루미늄 합금판재의 성형성에 대하여 기술한다. 차체용 Al합금판의 성형성을 인장시험, 헤밍시험, 스트레치 포오밍 시험 등으로 조사해 보았다. 냉연강판과 비교하여 현재의 차체용 Al합금판은 강도와 연신율 면에서 열세임에 틀림이 없으나, 앞으로 냉여강판에 버금가는 Al합금판이 나오리라 예상한다. 1. 시편의 종류. 2. 결정립 조직. 3. 집합 조직. 4. 상온 인장시험. 5. 고온 인장시험. 6. 헤밍시험(Hemming test). 7. 스트레치 포오밍 시험(Stretch forming test)

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.3
• /
• pp.38-52
• /
• 1997

Aluminum-faced honeycomb-cored sandwich panels as hull plating can provide structural weight savings when compared with the conventional aluminum single panels. The aim of the present paper is to confirm the feasibility of the sandwich panels for the hull material of fast ferries through designing an 80m class proto-type fast passenger/car ferry. For the case study, the structural design for the same principal particulars using the aluminum single panels is also performed, and the design results for the two types will be compared to confirm the weight savings between the two construction methods. The economics of a ship, being comprised of the shipbuilding cost and ship operaing cost, will require a cost analysis including a quantitative comparison between the two construction methods and the results of the cost analysis will be presented. Finally, the reasons why aluminum sandwich panels have not presently been used as the hull material for large size fast vessels will be discussed.

• Geophysics and Geophysical Exploration
• /
• v.14 no.4
• /
• pp.282-288
• /
• 2011

One of the most challenging issues facing shallow seismic survey is how to generate large amplitude of high frequency signal with small seismic sources. We tested the performance of the most commonly used shallow seismic source, hammer, with four plates: PE, nylon, aluminum, and steel plates. We compared their signal powers in terms of impulsive forces, accelerations, and ground vibration velocities caused by hammer impacts. According to a previous work, hammer blowing to an aluminum plate would generate the largest amplitude among four combinations. However, it was found in this experimental research that aluminum plate delivers seismic wave energy to the ground less than that generated with steel or PE plate. Even though the amplitude is relatively small, plastic plates could provide seismic pulses of 180 ~ 200 Hz in the bandwidth, and it seems to be very hard to generate seismic energy over the frequency of 250 Hz.

• Composites Research
• /
• v.14 no.6
• /
• pp.38-46
• /
• 2001

In this study, An optimization code that can design microwave absorbing composite laminates is developed, and 3-layered microwave absorbing composite laminates are developed by optimizing the thickness of each layer. The layers are 3 different composite laminates. Many variables including lay-up angles of electromagnetically orthotropic composite layer can be considered in this code. The developed laminate is composed of an impedance matching layer of glass/epoxy fabric laminate, a glass/epoxy fabric laminate layer containing aluminum filler and carbon/epoxy fabric laminate layer. Permittivities of the materials are obtained using a network analyzer and a coaxial air line.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.2-5
• /
• 2009

본 논문에서는 오실레이터 센서와 램파 센서를 결합하여 구조물 손상 진단을 위한 통합된 압전 센서 시스템을 제안한다. 구조물 손상으로 인한 공진주파수 변화를 관측할 수 있는 오실레이터 센서는 손상 정도에 민감하게 반응하고 구조가 단순한 장치이지만 측정 범위가 센서 주위로 제한되는 특성을 가진다. 반면에 램파를 이용한 진단 시스템은 원거리에 위치한 구조물의 손상부를 감지하기에 유용하다. 본 논문에서는 오실레이터 센서를 이용한 취약 지점의 국부적인 손상 진단 방식과 램파를 이용한 광역적인 손상 진단 방식을 결합하여 각 시스템의 장점들을 활용할 수 있는 센서 시스템의 적용가능성을 연구하였다. PZT소자를 알루미늄 판에 적용하여, 알루미늄판의 손상 정도에 따른 오실레이터 공진주파수의 변화와 램파 신호의 Time of flight, 그리고 진폭의 변화를 이용하여 구조물 손상형태의 판별 가능성을 제시하고 실험을 통하여 그 타당성을 검증하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.1 s.151
• /
• pp.32-39
• /
• 2007

A three-dimensional finite element model has been developed to simulate the MIG P/S welding process of two aluminum plates. The finite element calculations are performed using ANSYS finite element code, which takes into account the thermal and mechanical non-linear material properties. The results of finite element analysis compared with those of experiment to show its validity in view of distortions. Parametric studies are carried out on the validated model to assess the effects of various factors on the final residual distortion. Large deformations, temperature dependent material properties are included in the model. Finally, the formulas of fitting curves of angular distortion transverse shrinkage, and longitudinal shrinkage have been proposed.