• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.4
• /
• pp.308-315
• /
• 2018

In this paper, we present the basic design results for high-resolution radar development at S-band frequency that can precisely measure the miss distance between two targets. The basic system requirement is proposed for the design of a 3.5 GHz linear frequency-modulated (LFM) radar with maximum detection distance and distance resolution of 2 km and 1 m, respectively, and the specifications of each module are determined using the radar equation. Our calculations revealed a signal-to-noise ratio ${\geq}30dB$ with a bandwidth of 150 MHz, transmission power of 43 dBm for the power amplifier, gain of 26 dBi for the antenna, noise figure of 8 dB, and radar cross-section of $1m^2$ at a target distance of 2 km from the radar. Based on the calculation results and the theory and method of LFM radar design, the hardware was designed using software defined radar technology. The results of the subsequent field test are presented that prove that the designed radar system satisfies the requirements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.286-297
• /
• 2017

This paper is a study of 6~18 GHz wideband high power amplifier which is composed of 10 single amplifier and coaxial type spatial power combiner. The property of this spatial power combiner is on a similar principle to antipodal antenna radiation mechanism. Therefore, the key structure of proposed spatial power combiner is the antipodal finline PCB board and the finline curve shape is numerically synthesized by using Klopfensein's optimum impedance taper. The measured CW output power of spatial combined high power amplifier is nearly 50 W. In conclusion we prove the good combining performance between the spatial power combiner and 10 single amplifier over 6~18 GHz frequency ranges. Also, we developed the key component PA and MFC MMIC which controls the phase and gain of the each amplifier, The main characteristic of MFC MMIC is to maximize combining efficiency of power amplifier.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4C
• /
• pp.414-423
• /
• 2009

This paper considers a linear precoding scheme that achieves near optimal sum rate. While the minimum mean square error (MMSE) precoding provides the better MSE performance at all signal-to-noise ratio (SNR) than the zero forcing (ZF) precoding, its sum rate shows superior performance to ZF precoding at low SNR but inferior performance to ZF precoding at high SNR, From this observation, we first propose a near optimal linear precoding scheme in terms of sum rate. The resulting precoding scheme regularizes ZF precoding to maximize the sum rate, resulting in better sum rate performance than both ZF precoding and MMSE precoding at all SNR ranges. To find regularization parameters, we propose a simple algorithm such that locally maximal sum rate is achieved. As a low complexity alternative, we also propose a simple power re-allocation scheme in the conventional regularized channel inversion scheme. Finally, the proposed scheme is tested under the presence of channel estimation error. By simulation, we show that the proposed scheme can maintain the performance gain in the presence of channel estimation error and is robust to the channel estimation error.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1864-1869
• /
• 2012

We make an interference analysis to obtain a critical ctiteria for coexisting availability of WLAN and WiBro between adjacent channels can be used in TVWS(TV White Space). To meet this analysis, we set the various transmission parameters including the emission and blocking mask, antenna height and gain, transmission power and bandwidth, channel model etc. And, based on these parameters, we analyze on performances according to a variation of guard band, a number of service user and allowable transmit power of the user operating in the adjacent channels. In this paper, we consider a urban environment and apply a Extended Hata-SRD for WLAN and an interference link and Extended Hata model for WiBro, respectively. With these results, we can see how each system can be shared in an adjacent channel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.884-890
• /
• 2003

In order to reduce the specific absorption rate(SAR) in a human head exposed to electromagnetic fields radiated by a cellular phone, we have analyzed an electromagnetic wave absorber attached to the handset. A manufactured electromagnetic wave absorber was composed of Mn - Zn, which had complex relative permittivity of 7.30-j0.05 and permeability of 2.20-i1.55. The SAR value from the electromagnetic wave absorber attachment was calculated by using the nonuniform finite difference time domain(FDTD) algorithm and measured by phantom model at 835 MHz. The SAR reduction due to the electromagnetic wave absorber are about 18 % at 835 MHz. The V.S.W.R and radiation pattern of antenna are good agreement with the normal antenna. The gain reduction due to the electromagnetic wave absorber are only 0.3 dB at 835 MHz. But the sensitivity of cellular phone generally improves about 1 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.9
• /
• pp.1107-1115
• /
• 2012

This paper presents the development processes of a microwave radiometer for remote sensing of water surface temperature. Achieving the measurement accuracy within $2^{\circ}C$ for water surface temperature of $5{\sim}30^{\circ}C$, the requirements and specifications of the microwave radiometer and its receiver are drawn. The receiver with high gain, high sensitivity is designed and implemented. The receiver has the bandwidth of 50 MHz, the system gain of 45.2 dB and the sensitivity of 0.56K at 5.02 GHz. The effectiveness of the developed microwave radiometer in the measurement of water surface temperature is demonstrated experimentally. The results show the microwave radiometer can detect water surface temperature for $7.5{\sim}18^{\circ}C$ within the accuracy of $0.45^{\circ}C$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.9
• /
• pp.900-907
• /
• 2013

The development processes of a L-band microwave radiometer for remote sensing of water surface salinity are described in this paper. Achieving the development aim of the measurement accuracy within 2 psu for water surface salinity of 0~40 psu, the requirements and specifications of the microwave radiometer and its receiver are drawn. The receiver with high gain, high sensitivity is designed and implemented to satisfy these requirements and specifications. The receiver has the bandwidth of 45 MHz, the system gain of 47 dB and the sensitivity of 0.41 K at 1,390 MHz. The effectiveness of the developed L-band microwave radiometer for remote sensing of water surface salinity is demonstrated experimentally. The results show the microwave radiometer can detect water surface salinity for 10~28 psu within the accuracy of 1.4 psu.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.941-944
• /
• 2015

In this paper study for VSAT(very small aperture terminal) LNB(low noise block). ship LNB was demanded high stability and low noise figure. We designed FEM(Front-End Module) that was operated multi-band. FEM designed was constructed in a multi-band low noise receiver amplifier, a frequency converter, IF amplifier, Voltage Control Oscillator signal generating circuit four circuit using. To convert the multi-band 2.05GHz band, it generates four local oscillator signals, the four(band1, band2, band3, band4) designed to output an IF signal developed conversion apparatus, the conversion gain 64dB, noise figure 1dB or less, output P1dB 15dBm or more, phase noise showed -73dBc@100Hz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2C
• /
• pp.86-92
• /
• 2011

This paper details the downlink performance analysis of an multiple antennas system that combines adaptive beamforming and spatial multiplexing (SM) Multiple Input Multiple Output (MIMO). The combination of MIMO signal processing with adaptive beamforming is applied to WiBro, the South Korean Orthogonal Frequency Division Multiple Access (OFDMA) system that follows the IEEE 802.16e standard. Performance analysis is based on the results of experiments and simulations obtained from a fixed-point simulation testbed. Simulations demonstrate that the MIMO Beamforming OFDMA system improves the required signal to noise ratio (SNR) over the conventional MIMO OFDMA system by 3 dB (QPSK) / 2.5 dB (16-QAM) for the frame error rate (FER) of 1% in the WiBro signal environments. From the implementation of the fixed-point simulation testbed and its experimental results, we verify the feasibility of the MIMO Beamforming technology for realizing a practical WiBro base station.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.98-106
• /
• 2008

To reduce the outage probability and to increase the transmission capacity, the importance of repeaters in cellular systems keeps increasing. Unlike optical repeaters which require wireline connections, RF repeaters are easy to install, have low limitations in location and also have a reduced operational expense such as the optical fiber maintenance cost. On the other hand, RF repeaters suffer the interference due to the feedback signals between the transmitter and receiver antennas, hence require an extra interference cancellation method when the amount of the feedback signal reduction by using the shielding is not sufficient. In this paper, a channel estimation method for two-path feedback interference signals in the ICS (Interference Cancellation System) repeaters using baseband signal processing is proposed and its performance is evaluated. When compared with the conventional method which estimates each multipath individually, the proposed method achieves 10 dB performance gain in terms of the normalized mean-squared-error.