• Journal of the Korean Society for Railway
• /
• v.15 no.3
• /
• pp.257-265
• /
• 2012

Since the collapse of MSE walls frequently occurs due to the rainfall, it is necessary to analyze the behavior of MSE wall depending on the characteristics of rainfall and the properties of permeability of backfill. In order to understand the behavior of MSE wall depending on the characteristics of rainfall and the properties of permeability of backfill, finite element analyses were performed on the typical MSE wall. With varying ratio of saturated permeability to rainfall intensity, porepressures, displacements and factor of safety were analyzed. As the ratio of the saturated permeability to rainfall intensity increases, the global factor of safety is found to increase. Based on the analyses, the use of permeability of backfill with $2.56{\times}10^{-5}m/sec$ is desirable considering the characteristics of rainfall in Korea.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.6
• /
• pp.78-85
• /
• 2007

In this study, we performed finite element analysis for the design of a medical centrifuge and two-types of centrifuge were compared with each other. The types of centrifuge are 2-arm straight type and 3-arm type. Structural analysis was done with respect to the change of the rotational speed of the rotor of a centrifuge. When the rotor of centrifuge was rotated, the von Mises stress of 2-arm straight type-rotor was compared with the von Mises stress of 3-arm type. The margin of safety was estimated from the result. We found the critical speed of centrifuge from the campbell diagram by modal analysis.

• Proceedings of the Safety Management and Science Conference
• /
• 2004.05a
• /
• pp.219-231
• /
• 2004

The Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on polymeric materials. An analysis method for rubber toughened PVC is suggested to evaluated critical dynamic strain energy release rates(G$_c$) from the Charpy impact tester was used to extract ancillary information concerning fracture parameters in additional to total fracture energies and maximum critical loads. The dynamic stress intensity factor KID was computed for varying amounts of rubber contents from the obtain maximum critical loads and also toughening effects were investigated as well. The fracture surfaces produced under low velocity impact for PVC/MBS composites were investigated by SEM. The results show that MBS rubber is very effective reinforcement material for toughening PVC.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.4 no.2
• /
• pp.1-9
• /
• 1986

The marathon course on road surfaces varies frequently in alignment horizontally and /or vertically. This fact compelled use to use a calibrated bicycle method for the course measurement, and to be required statistical approaches for data processing. This paper deals with the computation of the Seoul Olympic Marathon course lengths measured on May 18, 1986. The concept of safety factor against short course is analyzed for certification, and statistical methods are presented to compute an appropriate safety factor. The results of computation show that the best (lowest) actual measurement provides about 99.95% confidence that the combined lengths of all intervals will not be found short upon an equally accurate remeasurement.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.929-935
• /
• 2018

This paper develops a flow control block for a hydraulic system of a tunnel boring machine. The flow control block is a necessary component to ensure stability in the operation of the hydraulic system. In order to know the pressure distribution of the flow control block, the flow analysis was performed using the ANSYS-CFX. It was confirmed that the pressure and flow rate were normally supplied to the hydraulic system even if one of the four ports of the flow control block was not operated. In order to evaluate the structural stability of the flow control block, structural analysis was performed using the ANSYS WORKBENCH. As a result, the safety factor of the flow control block is 1.54 and the structural stability is secured.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.3
• /
• pp.156-162
• /
• 2010

When eccentric or inclined load acts on foundation of the port & harbor structures, partial safety factors of bearing capacity limit state were estimated using reliability analysis. Current Korean technical standards of port and harbor structures recommend to estimate the geotechnical bearing capacity using the simplified Bishop method. In practice, however, simple method of comparing ground reaction resistance with allowable bearing capacity has been mostly used by design engineers. While the simple method gives just one number fixed but somewhat convenient, it could not consider the uncertainty of soil properties depending on site by site. Thus, in this paper, partial safety factors for each design variable were determined so that designers do perform reliability-based level 1 design for bearing capacity limit state. For these, reliability index and their sensitivities were gained throughout the first order reliability method(FORM), and the variability of the random variables was also considered. In order to verify partial safety factors determined here, a comparison with foreign design codes was carried out and were found to be reasonable in practical design.

• Journal of Korea Water Resources Association
• /
• v.51 no.7
• /
• pp.543-554
• /
• 2018

A methodology has been presented for evaluating the partial safety factors on the sliding failure mode of vertical caissons of composite breakwaters and for determining the cross sections of those by Level I reliability-based design method. Especially, a mathematical model has been suggested for the sake of a consistency of code format as well as convenience of application in practical design, for which the uncertainties associated with buoyancy and its own weight can be taken into account straightforwardly. Furthermore, design criteria equation has been derived by considering accurately the effect of uplift pressure, so that the cross sections of caissons can be assessed which must be safe against the sliding failure. It has been found that cross sections estimated from partial safety factors proposed in this paper are in very good agreement with the results of Level II AFDA and Level III MCS under the same target probability of failure. However, partial safety factors of the Technical Standards and Commentaries for Port and Harbour Facilities in Japan and Coastal Engineering Manual in USA tend to estimate much bigger or smaller cross sections in comparison to the present results. Finally, many reliability re-analyses have been performed in order to conform whether the stability level of cross section estimated by Level I reliability-based design method is satisfied with the target probability of failure of partial safety factors or not.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.72-80
• /
• 2004

LOX pump is one of the sub-assemblies constructing turbopump unit. In the current study, static structural analysis on such rotating parts as impeller and inducer has been carried out. Three major factors which can affect the structural stability of the rotating parts of LOX pump, are temperature, pressure, and centrifugal force. The effect of each factor was preliminarily investigated, then the analysis under the consideration of the combined loading conditions has been carried out. The major factor that affects the structural stability was proved to be temperature. The analyses of the combined cases showed that the designed impeller and inducer had reasonable safety margins, which means that the impeller and the inducer will be stable in static structural strength. Although there was no problem in the structural strength of the impeller and the inducer, a model analysis should be followed in order to verify the interference between the rotating part and the inner surface of casing.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.11
• /
• pp.78-86
• /
• 2020

A stress analysis was performed to verify the stability of the digging part of a garlic harvester. A finite element analysis was performed to examine the distribution and concentrated loads on the digging part of the blade and contact plate. Moreover, the stability and maximum deformation of the digging part were determined. Under a distributed load, the maximum principal stress, total deformation, and minimum safety factor ranged from 64-128 MPa, 0.35-0.70 mm, and 2.9-5.7, respectively. The analysis results for the distribution load indicated that the maximum stress occurred at the center of the blade. In contrast, under the concentrated load, the maximum principal stress, total deformation, and minimum safety factor ranged from 66-247 MPa, 0.35-0.79 mm, 1.48-5.53, respectively. The analysis results for the concentrated load indicated that stress and deformation were larger toward the edge and center, respectively.

• Journal of Korea Ship Safrty Technology Authority
• /
• v.12
• /
• pp.36-43
• /
• 2003

Fatigue life estimation by the theoretical stress concentration factors are, in general, considerably different from test results. And in calculating stress concentration factor, it is very difficult to consider actual geometry and material property which are the notch shapes, imperfections or defects of materials such as porosities inclusions and casting defects, etc. Therefore, the paper deals with the experimental method to find out the more exact stress concentration factors by measuring the strain distributions on each specimen by 3D-ESPI(Electronic Speckle Pattern Interferometry) System. Then the fatigue lives are compared between theoretical calculations using stress concentration factors determined by 3D-ESPI system and fatigue test results