• 대한기계학회논문집B
• /
• 제36권11호
• /
• pp.1073-1079
• /
• 2012

본 논문은 나노유체를 적용하여 써모사이폰 열전달 성능 특성 변화를 실험적으로 규명하는 것을 목적으로 하고 있다. 이를 위하여, 증발부 내부체적을 공유하는 3 개의 독립된 파이프를 가지는 써모사이폰을 제작하였으며 증류수, Ag 나노유체 그리고 $TiO_2$ 나노유체에 대하여 충진량, 증발부에 가해지는 입력열량 그리고 농도변화에 따른 써모사이폰 성능특성 변화를 고찰하였다. 증류수를 작동유체로 사용하는 경우 써모사이폰의 최적충진량은 30%로 결정되었고, $TiO_2$ 나노유체를 적용하는 써모사이폰 열저항이 Ag 나노유체를 적용한 경우에 비하여 평균 18.1% 감소하였다. 또한, 300W 입력열량 및 $TiO_2$ 나노유체 농도 1%에서 써모사이폰의 열전달 성능은 가장 우수하였다.

• 마이크로전자및패키징학회지
• /
• 제5권2호
• /
• pp.27-36
• /
• 1998

통신시스템의 고발열 전자부품 냉각을 위해 3종류의 써모싸이폰을 각각의 용도에 따라 개 발하였으며 그 각각의 설계변수에 대한 냉각특성을 실험적으로 구하였다. TS-I에서는 증발부 내부 에 금속스크린 메쉬형심지를 삽입함으로써 시간에 따른 온도 변화를 작게 하여 냉각성능 안정성을 확보하였고, TS-II에서는 9W/cm2의 높은 냉각성능을 가진 루프형 써모사이폰을 개발하였으며 TS-III에서는 작동유체의 종류, 파이프개수 와이어 삽입여부등 써모사이폰의 주요 설계변수에 따 른 냉각특성을 구하였다.

• 설비공학논문집
• /
• 제13권6호
• /
• pp.462-473
• /
• 2001

Due to the coupling between momentum and energy transport theoretical analysis of the loop performance is very complicate, therefore it is necessary that these problems be solved by experimental investigation before applying th loop thermosyphon to heat exchanger design. The evaporator and condenser of the loop thermosyphon were made of carbon-steel, and distilled water was used as working fluid in the experiments. From the experimental data correlations of heat transfer coefficient for evaporator and condenser sections were obtained. For heat fluxes in th range of 13~78kW/$m^2$, the correlation equations of heat transfer coefficients in evaporator and condenser predict the experimental behavior to within $\p$\pm$5% and\;\pm20$% respectively.

• 대한기계학회논문집B
• /
• 제28권4호
• /
• pp.415-424
• /
• 2004

Cooling the electronic equipment is one of the major focal points of the design process and the key to successful product launch. The two-phase loop thermosyphone which is a good candidate among many available options was investigated fur cooling of the high power amplifiers. The system is composed of evaporator which contains 6 parallel cold plates, fan cooled condenser, gas-liquid separator, and interconnecting tubes. Experiments were performed for several refrigerant charging values, hs and as a experiment result, the optimum charging value fur this system was proposed. In order to optimize the system design, the operating cycle pressure and inlet/outlet temperatures of evaporator and condenser are measured and analyzed. The effect of the three parameters such as flow rate and temperature of condenser cooling air, and thermal load on the evaporator are investigated. The lower the operating pressure and the cycle temperatures are also better to prevent the leakage of the system. The system invesigated in this paper can be directly used for cooling of a real unmanned wireless communication station.

• 설비공학논문집
• /
• 제10권2호
• /
• pp.137-146
• /
• 1998

The experimental study is concerned with two-phase closed thermosyphons, (i.e., wickless heat pipes) for the cooling of high power electronic components in telecommunication system. The thermosyphon which can deal with a high heat flux of up to $4.9W/cm^2$ is developed, and the cooling characteristics of thermosyphon is analyzed according to design parameters which are the types of and quantity of working fluid, number of pipes, wire insertion in pipe, inclination angle of thermosyphon, and cooling air velocity. Using water as working fluid is superior cooling performance compared to using acetone, and cooling performance is improved as the number of thermosyphon becomes larger, inserting wires in the pipes, and inclination of $30~60^{\circ}$.

• 설비공학논문집
• /
• 제10권2호
• /
• pp.165-172
• /
• 1998

An experimental study on the heat transfer of the inclined thermosyphon with low integral-fins in which boiling and condensation occurred is performed to investigate its heat transfer performance. Water and CFC-30 have been used as the working fluids. The operating temperature and the inclination angle of thermosyphon have been used as the experimental parameters. The heat flux input and the inclination angle $\theta$ towards the vertical position were varied in steps. The heat transfer rate in the thermosyphon was depended upon the inclination angle. In addition, it is to obtain the overall heat transfer coefficients and the characteristics as a operating temperature for the practical applications.

• 설비공학논문집
• /
• 제10권1호
• /
• pp.22-32
• /
• 1998

Separate type thermosyphon has larger critical heat flux than non-loop type thermosyphon, because the flooding phenomenon of vapor and liquid occurring in non-loop one does not occur. The experimental study has been carried out separate type thermosyphon with single tube. An investigation of heat transfer characteristics in separate type thermosyphon is performed experimentally. Heat transfer coefficients in an evaporator and condenser were measured experimentally. The effects of liquid filling ratio, height difference, cooling temperature and heat flux on the heat transfer coefficients were examined. As a result, the reasonable range of the liquid filling ratio and the dependence of heat transfer on vapor temperature and heat flux are obtained.

• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1475-1483
• /
• 2004

Loop thermosyphon(LTS) has many good characteristics such as low thermal resistance, no power consumption, noiseless operation and small size. To investigate the overall performance of LTS, we have performed various experiments varying three parameters: input power of the heater, working fluid(water, ethanol, FC3283) and filling ratio of the working fluid. At a combination of these parameters, temperature measurements are made at many locations of the LTS. The temperature difference between the evaporator and the condenser is used to obtain the thermal resistance. In addition, flow visualization using a high speed camera is carried out. The thermal resistance is not constant. It is lower at higher input power, which is one of the distinct merits of LTS. Flow instabilities are frequently observed when changing the working fluid, the input power and the filling ratio. The results show that the LTS can be readily put into practical use. Future practical application in electronic cooling is recommended.

• 한국분무공학회지
• /
• 제7권2호
• /
• pp.31-36
• /
• 2002

According to the improvement of PC performance, it is expected that calorific value, which causes PC to malfunction, is increased. Therefore, the development of new cooling system is recently required. As the method to solve this problem, we applied loop heat pipe to PC cooling system. The advantage of the loop heat pipe is that it has a small size, light weight, simple shape, long life and it has a good performance on heat transfer, no-noise, wide range of applicable temperature and no supply of power from the outside. It is confirmed that loop heat pipe reduces thermal resistance and has a good performance on PC cooling.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1998년도 추계 학술발표회 논문집
• /
• pp.193-208
• /
• 1998

본 논문에서는 써모싸이폰식 히트파이프의 열수송한계와 작동유체의 주입량이 파이프의 직경, 가열량 및 증발부와 응축부의 길이비 등에 따라 변화하므로 이러한 인자에 따른 적정 작동유체의 주입량과 가열량의 한계에 대해 고찰하였다. 특히 각종 전자부품의 냉각에 사용되는 히트파이프가 써모사이폰식이므로 사용작동유체에 대해 가열량에 따라 파이프의 직경예측이 가능토록 열수송한계특성에 대해 검토하고, 싸이리스터용은 증발부와 응축부의 길이비 변동이 심하므로 작동유체의 주입량이 중요한 성능인자로 작용하므로 길이비에 따른 작동유체의 주입량범위에 대해 기술하였다. 그리고 최적의 작동유체범위와 히트파이프의 증발열전달계수 및 응축열전달계수에 대한 실험으로부터 성능자료를 도출하여 이론해석과 비교검토하였다.