• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.558-570
• /
• 2015

A study on the green ship design for Ultra Large Container Ship (ULCS, 18,000 TEU Class Container Ship) was performed based on the four step procedures of the initial design and hull form optimization to maximize economic and propulsive performance. The first, the design procedure for ULCS was surveyed with economic evaluation considering environmental rules and regulations. The second, the characteristics of single and twin skeg container ships were investigated in view of initial design and performances. The third, the hull form optimization for single and twin skeg ships with the same dimensions was conducted to improve the resistance and propulsive performances at design draught and speed by several variations and the results of the optimization were verified by numerical calculations of CFD and model test. The last, for the estimated operating profile of draught and speed, the hull forms of single and twin sked ships were optimized by CFD. From this study, the methodologies to optimize the hull form of ULCS were proposed with considerations during the green ship design and the improvement of the energy efficiency for the optimized hull forms was confirmed by the proposed formula of the total energy considering design conditions, operating profile and fuel oil consumption.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.6
• /
• pp.551-563
• /
• 2007

Numerical analysis for flow characteristics of a twin skeg container ship was carried out according to skeg vertical angles($0^{\circ}$, $10^{\circ}$, $20^{\circ}$) and skeg distances(16m, 20m, 24m) by using a commercial CFD code, FLUENT. Computed: pressure distributions, wake distributions and resistance coefficients have been compared with experimental and WAVIS results carried out by MOERI. Flow characteristics from numerical analysis such as nominal wake fractions, wake distribution and directions of the transverse vectors give good agreement with WAVIS results, even though there are quantitative discrepancy comparing with experimental measurements at the propeller plane. It is found that the better resistance performance can be obtained with the increase of the skeg vertical angle and the decrease of the skeg distance, which are mainly caused by viscous pressure resistance due to the skeg form and pressure recovery around the skeg. In addition, a vertical angle of the skeg gives more effect to the resistance coefficient comparing with the skeg distance. On the basis of results of the present study, it shows that numerical analysis using the commercial code, FLUENT, is useful and efficient tool for the evaluation of the complex stern hull form with twin-skegs.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.4
• /
• pp.361-369
• /
• 2008

The optimized distance between skegs and angle of the skeg for a standard twin-skeg type LNG carrier were presented using the CFD and model tests. The evaluation method of self-propulsion performance was derived based on the results of CFD and confirmed the validity through model tests. The analyses to assess self-propulsion performance using CFD were shown by flow line patterns on the skeg surface, nominal wake distribution in the propeller plane and the evaluation for flow balance around stern skegs. The optimized ship that was applied to the optimized two design parameters in stern skeg arrangement for target ship was derived in this work. Finally speed performance of mother ship which is existing ship and optimized ship were compared through CFD and model tests. And the usefulness about the evaluation method of self-propulsion performance was reconfirmed.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.1
• /
• pp.15-22
• /
• 2004

Twin-skeg type stern shapes are recently adopted for very large commercial ships. However it is difficult to apply a CFD system to a hull form having twin-skeg, since grid topology around a twin-skeg type stern is more complicated than that of a conventional single-screw ship, or of an open-shaft type twin-screw ship with center-skeg. In the present study a surface mesh generator and a multi-block field grid generation program have been developed for twin-skeg type stern. Furthermore, multi-block flow solvers are utilized for potential and viscous flow analysis around a twin-skeg type stern The present computational system is applied to a 15,000TEU container ship with twin-skeg to prove the applicability. Wave profiles and wake distribution are calculated using the developed flow analysis tools and the results are compared with towing tank measurements.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.11a
• /
• pp.187-187
• /
• 2022

최근 선박의 자율운항기술이 활발하게 연구되어 오면서, 경로추종 제어 및 충돌회피 등의 자율운항 기술 연구가 많이 진행되고 있으며 그에 따른 시뮬레이션과 실해역 시험 등도 활발하게 수행되고 있다. 이러한 자율운항기술 중 본 연구에서는 AUV(Autonomous Underwater Vehicle) 진회수 시 모함에 활용되며 쌍동선형을 갖는 쌍동형 무인수상선을 대상으로 경로추종 제어에 대한 실해역 시험을 수행한 내용을 소개한다. 대상선인 쌍동형 무인수상선은 배수량이 약 10ton, 최대속도 10knots를 기준으로 설계된 선형이며 Sail drive 타입의 쌍축 추진기를 탑재하고 있으며 Fig. 1에 나타내었다. 실해역 시험은 경기도 화성시에 위치한 제부마리나 전면 해역에서 여러 속도에 대해 Fig. 2의 경로(빨간색)를 활용하여 수행되었다. 해당 경로는 변침각이 45도까지 이루어져 있다. 경로추종 제어 알고리즘은 목표경유점을 향하기 위해 선수각을 제어하는 부분과 목표속도로 추진하기 위해 속도를 제어하는 부분으로 나뉘어져 있다. 선수각 제어 시 경로와 무인선과의 위치 오차를 줄이는 방향으로 선수각이 향할 수 있도록 알고리즘이 설계되었다. 속도 제어의 경우 RPM 별로 실제 속도를 계측하여 데이터화 한 후, 실제 속도가 명령 속도와 다를 경우 RPM을 가감하여 명령 속도로 추진하기 위해 제어할 수 있도록 하였다. Fig. 2에서 파란색 선은 설계한 알고리즘을 활용하여 경로추종 제어를 한 결과의 궤적을 보여준다.