• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.92-99
• /
• 2006

The swirl ratio of a charge in the cylinder was estimated by calculating the ratio of the rotary speed of charge which could be simulated from the rotary speed of paddle in the swirl measurement apparatus, to the engine speed which could be calculated by measuring intake air flow rate. The automation of the swirl ratio measurement for cylinder head was achieved by controling both valve lift in cylinder head and a suction pressure of surge tank using two step-motors. The number of measurement position for calculating mean swirl ratio was varied by adjusting the interval of valve lift. The mean swirl ratio with varying the number of measurement position showed nearly constant value. Two measurement methods for measuring the swirl ratio were compared, one was to control the suction pressure of the surge tank with PID (proportional, integral, differential) mode with by-pass valve controlled by the step motor and the other did not control the surge tank pressure by fixing the by-pass valve. The difference of the mean swirl ratio between the two measurement methods showed nearly constant value with varying the number of measurement position. This means that the w/o PID control method could be preferred to the PID control method which has been used, due to the simpleness of the swirl measurement.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.790-795
• /
• 2001

Since the characteristics of combustion and pollutant in Diesel engines were mainly affected by the characteristics of in-cylinder gas flow and fuel spray, an understanding of those was essential to the design of the D.I. Diesel engines. The improvement of volumetric efficiency of air charging into combustion chamber is a primary requirement to obtain better mean effective pressure of an engine. Since the air resistances in intake and exhaust flow passages, valve lift and valve shape influence greatly to the volumetric efficiency, it is very important to investigate the flow characteristics of intake and exhaust port which develops air motion in the combustion chamber. This paper presents the results of an experimental investigation of steady flow through the various kinds of commercial cylinder head ports, and the development procedures of HHI's H21/32 prototype cylinder head ports.

• Tribology and Lubricants
• /
• 제27권2호
• /
• pp.65-70
• /
• 2011

The power servo cylinder for driving accurately turbine stop valve of an atomic power plant is necessary to do turn-over owing to a leakage of oil and a structure problem, especially, it of a power plant be in demand a high quality standard depends entirely on import. There are much problem that the AlBC be to used as a material of piston head in cylinder are caused by wear. Therefore, it is necessary to examine friction characteristics of it. In this study, wear test experiments was carried out with AlBC and SCM440, using reciprocating friction tester of pin on disk. This result was shown that the wear mechanism of AlBC on working condition is adhesive wear and the maximum temperature of infra redray thermal image of frictional surface show over 2 mm from contact surface of pin and disk.

• 한국경영과학회:학술대회논문집
• /
• 한국경영과학회/대한산업공학회 2003년도 춘계공동학술대회
• /
• pp.118-122
• /
• 2003

본 연구를 시물레이션방법을 이용한 실린더 헤드라인 생산설비의 적정계획 및 성능산정을 위해 가용한 생산설비의 자료들로부터 요구되는 생산능력을 만족하는 생산설비를 구성한다. 구성된 설비들은 가용한 생산설비 운영조건을 고려한 가상의 시물레이션 모델로 구축하여 생산설비의 적정 구성 및 공정간의 재고 등을 산정한다. 시스템 성능 산정을 위해 본 연구에서는 AutoMod 시물레이터를 이용하여 실린더 헤드라인의 생산설비계획 문제에 적용한다. 본 연구는 다수의 생산설비를 이용한 설비계획 연구시 사전 분석과 능력산정 및 기존의 설비 운영 조건에 따른 생산능력산정에 유용할 수 있으며 3차원 동영상으로 분석 결과를 제시할 수 있다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 추계학술대회 논문
• /
• pp.126-132
• /
• 1996

This study is pre-research to evaluate the reasonability of convertion aluminum alloy cylinder head cover into plastic cylinder head cover using finite element analysis. The basedata which are needed in design are shown. On processing the study size of mesh and kind of elements are varied and adaptiv method is used.

• Journal of Biosystems Engineering
• /
• 제6권2호
• /
• pp.9-19
• /
• 1982

소형(小型) 디젤엔진의 예연소실(豫燃燒室) 형상(形狀)이 저온시(低溫時)의 시동성(始動性)에 미치는 영향(影響)을 구명(究明)하기 위해 8종(種)의 예연소실(豫燃燒室)과 2종(種)의 실린더헤드를 제작(製作)하여 $2^7$ 요인실험법(要因實驗法)에 의해 1회(回) 조작시(操作時) 최저(最低) 시동가능(始動可能) 온도(溫度), 최대출력(最大出力), 전부하(全負荷)(4/4) 및 과부하(過負荷)(11/10)시(時)의 연료소비율(燃料消費率)을 측정(測定)하여 분석(分析)한 결과(結果)를 요약(要約)하연 다음과 같다. 가. 피스톤 상면(上面)에 대한 주분사구(主噴射口)의 상대각도(相對角度)가 $20^{\circ}$에서 $18^{\circ}$로 감소(減少)하면 최저(最低) 시동가능(始動可能) 온도(溫度)가 약(約) $2.4^{\circ}C$ 낮아졌으며 최대출력(最大出力)은 약(約) 0.3ps 증가(增加)되었다. 나. 실린더헤드 홈 각도(角度)가 $20^{\circ}$에서 $18^{\circ}$로 작아짐에 따라 최저(最低) 시동가능(始動可能) 온도(溫度)가 약(約) $3.3^{\circ}C$ 낮아졌으며, 최대출력(最大出力)은 약(約) 0.3ps 감소(減少)되었다. 다. 예연소실(豫燃燒室) 길이가 17.5mm에서 15.5mm로 짧아지면 최저(最低) 시동가능(始動可能) 온도(溫度)가 $2^{\circ}C$ 낮아졌으며 최대출력(最大出力)은 0.2ps정도(程度) 감소(減少)되었다. 라. 주분사구(主噴射口) 직경(直俓)이 4.8mm에서 4.5mm로 작아지면 최대출력(最大出力)은 0.2ps정도(程度) 증가(增加)했으나, 주분사구(主噴射口) 직경(直俓)만이 변화(變化)에 따른 시동성(始動性)의 차이(差異)는 인정(認定)되지 않았다. 마. 주분사구(主噴射口) 각도(角度)가 $47^{\circ}$이고 실린더헤드 홈 각도(角度)가 $18^{\circ}$일 경우(境遇) 시동가능(始動可能) 온도(溫度)가 가장 낮았으며, 주분사구(主噴射口) 직경(直俓)이 4.5mm이고 예연소실(豫燃燒室) 길이가 17.5mm일 경우(境遇) 최대출력(最大出力)도 가장 높았고, 전부하(全負荷) 및 과부하시(過負荷時)의 연료소비율(燃料消費率)도 가장 낮았다. 바. 실린더 헤드홈 각도(角度)와 주분사구(主噴射口)의 각도(角度)가 각각(各各) 시동성(始動性) 향상(向上)에 가장 큰 영향(影響)을 미쳤으며, 또한 주분사구(主噴射口) 직경(直俓)과 예연소실(豫燃燒室) 길이와의 교호작용(交互作用)이 최대출력(最大出力)에 가장 큰 영향(影響)을 미쳤으므로 이들 요인(要因)에 대한 처리수(處理數)를 늘려 시험(試驗)해 볼 필요성(必要性)이 있는 것으로 사료(思料)된다. 사. 본(本) 실험(實驗)에서 최적조건(最適條件)으로 나타난 시작(試作) 예연소실(豫燃燒室)은 기존(旣存) 예연소실(豫燃燒室)보다 약(約) $-6^{\circ}C$의 시동성(始動性) 향상(向上)을 나타냈다.

• 한국정보통신학회논문지
• /
• 제4권4호
• /
• pp.901-905
• /
• 2000

본 연구는 미사일 헤드와 같은 돔형의 실린더형 ogive (Cylindrical Ogive)를 타원형 ogive(Elliptical Ogive)로 대치하여 지상의 레이다로부터 미사일의 탐지확률을 줄이는 연구이다. 미사일의 RCS(Radar Cross Section)를 계산하기 위해 GTD(Geometrical Theory of Diffraction)/UTD(Uniform GTD)를 사용하였다. 향후, 형상변경에 따른 미사일 헤드의 공기역학(aerodynamics)적인 타당성 검토가 이루어져야 한다.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.178-187
• /
• 1997

For the experimental measurement of heat flux of DI diesel engine combustion chamber, the instantaneous temperature probes and data acquisition system were developed. By the analysis of measured temperatures at the cylinder head, the temperature at the point 3 which is located between intake and exhaust valve was higher than that of the other points. Temperatures at the point located mear the exhaust valve were higher than those of intake valve. The instantaneous and mean temperature at the cylinder head increases proportionally to the increase of the engine speed, while the temperature swing varies inversely. Temperature swings have influence on the maximum heat flux values from gas into head surface. It has been verified that these probes and data acquisition system perform well by the comparison of the trend of instantaneous temperature variation with that of measured combustion chamber pressure variation with respect to crank angle. It is presumed that these probes could be used in the measurement of other parts of combustion chamber as piston, cylinder wall etc. for the future study.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.806-811
• /
• 2001

Since the characteristics of combustion and pollutant in Diesel engines were mainly effected by the characteristics of in-cylinder gas flow and fuel spray, an understanding of those was essential to the design of the D.I. Diesel engines. The improvement of volumetric efficiency of air charging into combustion chamber is a primary requirement to obtain better mean effective pressure of an engine. Since parameters such as the air resistances in intake and exhaust flow passages, valve lift and valve shape influence greatly to the volumetric efficiency, it is very important to investigate the flow characteristics of intake and exhaust port which develops air motion in the combustion chamber. In this study, two approach methods were used for design intake and exhaust port; experiment and computation which were made by using steady flow test rig and commercial CFD code. This paper presents the results of an experimental and analytical investigation of steady flow through the prototype cylinder head ports and valves of the HHI's H21/32 HIMSEN Engine.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.321-325
• /
• 2000

Gasket of vehicle engine maintains airtight between cylinder head and engine block under high temperature and pressure, and plays important role in heat conduction of engine. And the characterization of the nonlinear behavior of metal gasket fer various bead shapes is very important as basic research for estimation of gasket durability. But it is very difficult to analyze the behavior of gasket In real experiment. In this paper, to analysis effects of the bead shape on the nonlinear behavior of cylinder head gasket under uniform pressure, the virtual experiment using the nonlinear finite element method was performed. Results are analyzed with residual deformation and the sealing pressure. With the increase of the height and the width of bead, the residual deformation and the sealing pressure increase. And if the height is very high and the width is very narrow, the wrinkles are occurred in the gasket while working.