• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.06a
• /
• pp.99-110
• /
• 1998

• Economic and Environmental Geology
• /
• v.49 no.6
• /
• pp.479-490
• /
• 2016

Seabed drilling system has recently been used to drill seafloor mineral resources. This case report highlights the procedure and result of sea-trial of seabed drilling system at off-shore of Japan on March, 2016 as well as briefs an international-technical trend of seabed drilling system. In case of having less than 100 m drill depth, seabed drilling system is favorable for seafloor mineral deposits which are mostly distributed within a narrow district and situated between 1000~3000 m water depth, compared with vessel-mounted drilling system. The system is featured by the remotely-operated drill gear, which has top drives, drill strings and mud system on it. The core samples are generally recovered to ship with seabed driller after a dive. In this sea-trail, recovery rate of core samples averagely shows about 55% and the recovered rocks mostly correspond to fresh and/or weak-altered basalt. In case of drilling hydrothermal ore deposit, the recovery rate would be lower than 55% because of the fragile nature of ores. Alternatively it is used to collect cutting chips through riser or bins in order to increase the recovery rates. Recently a reverse circulation method is taken considered to acquire the better cutting-chips. Three-leg type outrigger system and four-leg type leveling system are the competing landing-instruments of seabed drill system. However the landing efficiency using these gears has to be further monitored due to lack of case reports.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.541-547
• /
• 2021

To assess the stability of a slope and the likelihood of its loss or collapse requires information about the ground, such as the composition of the stratum and its mechanical characteristics. This information is generally gathered through standard penetration testing (SPT) and cone penetration testing. SPT is not widely used due to problems with accessing slopes, most of which are steep and without ramps. A drop cone penetrometer, a portable device that can make up for these shortcomings, can be used in a limited way in some circumstances. Therefore, we developed a portable drilling machine and a small dynamic cone penetration test module that can easily access a slope site and perform SPT. The correlation of the developed system's results with those from SPT was analyzed. Analysis of the correlation between the energy shear rate passing to the load during the different test types established that the energy shear rate is reflected in the test result. The correlation between corrected dynamic cone penetration testing and corrected SPT was N_d' = 3.13 N'.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.333-341
• /
• 2014

Since distribution and preservation of cultural artifacts in the submarine sediments are directly affected by not only ocean currents and tides, but also their composition, it is very important to investigate geological characteristics of sediments and ocean-sediment interactions for maritime archaeological survey. Physical properties of submarine sediments, which are collected by grab sampler and vibro-corer, are analyzed in order to investigate effects of submarine environment on development of maritime archaeological survey techniques. Result of physical property analysis showed that bulk density, shear strength, and magnetic susceptibility increase with depth, while water contents and porosity decrease with depth. Since the magnetic susceptibility of bedrock is about 40 times that of submarine sediments, it might impact greatly on the response of magnetic survey. Physical properties of sediments with depth and sediment classification by Folk's ternary diagram indicate that submarine sediment mainly consists of silt, and cultural artifacts can not penetrate no deeper than 1.5 m in sediments.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.5 no.2
• /
• pp.20-26
• /
• 2009

The dominant incidents category for onshore and offshore natural gas transmission pipelines in the world is associated with outside forces. Incidents in the outside forces category embrace acts of nature, which typically cause widespread structural damage, as well as act of man, whose effects tend to cause dents and/or gouges localized at point of contact that are referred to as mechanical damage. Therefore, these damage types must be better addressed to avoid unnecessary and costly repairs and the possibility of catastrophic events. First of all, the characterizing features of mechanical damage in gas pipelines were evaluated by using of excavator or boring machine. There is no reliable method for evaluating the safe operating pressure of pipeline affected by mechanical damage. It is especially important to evaluate the remaining strength of damaged pipelines due to outside force. Therefore, the full scale burst tests were conducted to evaluate the remaining strength of pipe with mechanical damage that combines a dent and a gouge. This paper is supposed to provide information that will assist in developing a criterion to assess serviceability in pipelines with mechanical damage.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.1249-1253
• /
• 2005

대부분의 국내 다목적 댐은 유역면적이 넓고 강우기 집중강우로 인하여 유입되는 입자성 물질이 상당히 많은 편이며, 영양염의 증가로 인하여 저수지내부에서 발생되는 입자성 물질도 많다. 이로 인하여 호소에는 외부에서 유입된 무기$\cdot$유기성 입자와 내부 생성된 유기성 물질들이 장기간 축적되어 저수지 용량이 줄어든다. 본 연구에서는 저수지 퇴적물 상태를 탐사하는 효율적인 조사기법을 제시하고자 한다. 퇴적물 탐사기법에는 탄성파탐사 등을 이용하는 간접적인 방법과 코아를 이용하는 직접적인 방법, 퇴적층 동위원소 분석 기법 등이 있으며, 이러한 기법에 대한 기본원리 및 특성, 효용성 등을 평가하고 현장에 적합한 방법을 실제 적용하였다. 퇴적물 분포를 조사하기 위하여 먼저 다중빔(MBES)을 이용한 정밀 지형조사를 실시하였으며 이를 통하여 호저지형의 특징을 간접적으로 평가할 수 있었다. 직접적인 조사방법으로 gravity corer를 사용하여 몇 개의 지점을 sampling하였으며, 잠수부가 직접 핸드코아링를 실시하여 퇴적층을 측정하였다. 16지점에서 실시한Gravity core 결과 세 곳의 조사 정점에서 최대 70cm 두께의 퇴적층이 중력식 시추기에 의해 획득되었으며 다른 정점에서는 50cm, 20cm가 시추되었고 그 나머지 지점에서는 퇴적물이 채취되지 않았다. 이는 퇴적층이 얇아 코아가 쓰러지거나 시료채취가 되지 않은 것으로 판단되었다. 잠수부가 hand corer를 이용한 시료 채취시에 채취된 시료의 퇴적층은 각 지점별로 덕치리 25cm, 경계지점 25cm, 우산리 지점 45cm로 조사되었다. 납-210(반감기 22.3년)을 이용하여 최근에 형성된 주암댐 호수저 퇴적물 중 퇴적작용 이후 교란을 받지 않은 지역의 시추 시료를 대상으로 퇴적속도를 구하였다. 주암호에서 취한 코아퇴적물 시료는 현장에서 냉동하여 실험실에서 약 2cm 간격으로 절단하여 절단체 별로 동위원소 분석을 실시하였다. $^{210}Pb$의 농도는 grand-daughter인 $^{210}Po$를 측정함 후 감마분석에 의하여 구하였다. CF:CS 연령모델을 적용한 결과 깊이에 따른 supported $^{210}Pb$와 퇴적 속도는 0.91cm/year 인 것으로 산정 되었다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.22 no.3
• /
• pp.147-153
• /
• 1989

Laboratory measurement of compressional wave velocity for two piston cores has been carried out successfully. The cores penetrated into the Holocene mud deposit located just off the Pusan harbor. Differences between the mercury delay method using a mercury column and the time delay method utilizing a digital processing oscilloscope for the observed velocity are negligible. Thus, both methods can be used independently to determine the velocity of unconsolidated marine sediment. The core velocity is, however, always higher than the velocity calculated from the seismic profile. This result should be considered seriously to interprete a seismic profile, otherwise one may encounter systematic error in calculating sediment thickness.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2C
• /
• pp.125-131
• /
• 2008

Ground stiffness(shear wave velocity) is one of the key parameters in geotechnical earthquake engineering. An In-situ seismic technique has its own advantages and disadvantages over the others in stiffness measurements. By combining the crosshole and seismic cone techniques and utilizing favourable features of bender elements, a new hybrid probe has been developed in order to enhance data quality and easiness of testing. The basic structure of the probe, called "MudFork" is a fork composed of two blades, on each of which source and receiver bender elements were mounted respectively. To evaluate the disturbance caused by the penetration of the probe, shear wave velocity measurements were carried out in the Kaolinite slurry in the laboratory. Finally, the probe was penetrated in coastal mud near Incheon, Korea, using SPT(standard penetration test)rods pushed with a routine boring machine and shear wave velocity measurements were carried out. The results were verified with data from laboratory and cone testing. The performance of the probe turns out to be excellent in terms of data quality and testing convenience.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.6 no.4
• /
• pp.249-258
• /
• 2001

Compressional wave velocity and electrical resistivity of muddy sediments in the southeastern inner shelf of Korea were studied using nine piston core samples. The acoustic and physical properties were measured with 10 cm depth interval. Sediment structures were examined by x-radiographs of the cored sediments. Subbottom profiles were obtained by a high-resolution acoustic subbottom profiler. Acoustic turbid layers are clearly seen on the profiles, and x-radiographs of the sediments showed degassying structures formed by gas escaping. On the basis of x-radiographic images, velocities, electrical resistivities and physical properties, the sediments are divided into gassy and non-gassy sediments. The presence of gas and degassying structures result in a marked variation in velocity and electrical resistivity. It can be concluded that velocity and electrical resistivity arep arameter to recognize gassy sediment. The velocity is important parameter to indicate gassy sediment.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.9 no.1
• /
• pp.1-12
• /
• 2004

Sedimentary facies and high-resolution echo facies were analyzed to elucidate sedimentation pattern of the late Quaternary glacial-marine deposits in the northern continental margin of the South Shetland Islands. Six sedimentary facies are classified, based on grain texture and sedimentary structures in gravity cores. The high-resolution (3.5 ㎑) echo characters are classified into 6 echo facies on the basis of clarity, continuity, and shape of bottom and subbottom echoes together with seafloor topography. Distribution of the echo and sedimentary facies suggest that there was a significant change in sedimentation pattern between the Last Glacial Maximum (LGM) and subsequent glacier-retreating period. When the grounded glaciers extended to the present shelfbreak during LGM, coarse-grained subglacial tills were widespread in the shelf area, and deep troughs in the shelf were carved beneath the fast-flowing ice steam. As the glacial margin retreated landward after LGM, dense meltwater plumes released from the retreating ice-front were funneled along the glacier-carved troughs, and accumulated channel- or cannyon-fill deposits in the shelf and the upper to mid slope. At that time, slope sediments seem to have been reworked by slope failures and unsteady contour currents, and further transported by fine-grained turbidity currents along the South Shetland Trench. After the glacial retreat, sediments in the shelf and slope areas have been mainly introduced by persistent (hemi) pelagic settling, and fine-grained turbidity currents frequently occur along the axis of the South Shetland Trench.