• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.197-197
• /
• 2003

현재 PDP(Plasma Display Panel) 투명유전체층은 PbO 계열을 사용하고 있으나 제조공정 시 다량의 중금속 페기물이 방출됨에 따라 환경오염을 야기시킴으로 무연조성이며 저온소성이 가능한 저융점유리인 인산염계 유리에 대한 열적, 화학적, 광학적 특성에 대해 체계적인 연구가 진행되었다. 광학적 특성을 위 한 승온속도, 소성온도, 유지시간의 변화 그리고, 프릿 입도에 따른 광 투광성, 기포의 형성, 그리고 기포의 분포특성을 연구하였다. 열적특성은 DTA와 TMA를 이용하여 유리전이점(Tg) 및 선팽창계수(CTE)와 Littleton softning point (Ts)가 측정되었다. 광학적특성은 스크린프린팅법으로 후막 제조 후 소성하여 UV-visible spectrometer을 이용하여 300~800nm영역에서 투광성을 측정하였으며, FEG-SEM, AFM을 이용해 표면을 관찰하였다. 결과로써, Tg는 440-46$0^{\circ}C$ 와 CTE는 7~8.5$\times$$10^{-6}$K값을 보였고 높은 화학적 내구성과 60-80%의 광투과율을 나타내었다. 프릿의 미세화, 숭온속도의 감소는 기포의 생성을 줄이는데 효과를 보였으며, 그 결과 양호한 광투과율을 얻을 수 있었다. 이러한 결과에 따르면, P$_2$O$_{5}$-ZnO-RO 조성은 PDP용 투명유전체 조성으로써 기존의 PbO계열을 대체할만한 새로운 조성으로 고려된다.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.514-520
• /
• 1993

In this paper the cure cycle of carbon fiber/phenolic resin was investigated by the Taguchi Method in an experimental design. Experiments were systematically performed using $L_{18}(2^1 \times 3_7)$ orthorgonal array table of the experimental design. In the experimental design, eight compression molding parameters (heating rate, pressing temperature, pressing rate, molding pressure, curing temperature, dwell time at curing temperature, cooling rate and degassing) were considered and the effects of the parameters on the flexural strength and the apparent porosity of carbon fiber/phenolic composites were investigated. The analysis of variance for the experimental results indicated that molding pressure and curing temperature are the most significant parmeters in the flexural strength and the apparent porosity of carbon fiber/phenolic resin composites, respectively.

• Journal of Hydrogen and New Energy
• /
• v.28 no.4
• /
• pp.392-400
• /
• 2017

An experimental study was conducted to investigate behavior of steel surface oxidation with characteristics of the combustion. The excess entalphy combustion in porous media system was applied to implement the direct radiation heating system. The surface oxidation thickness (SOT) of fuel-lean was thicker than the SOT of fuel-rich. Also, the SOT was increased by increasing residence time. Detailed explanations were given by SEM and EDS analysis.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2012.04a
• /
• pp.345-348
• /
• 2012

본 연구는 Zn-Al혼합물 분진의 화재폭발사고예방을 위한 안전자료 확보를 목적으로 최소발화온도를 실험적으로 조사하였다. Zn-Al혼합물의 최소발화온도 측정은 퇴적두께 10 mm, 직경 100 mm의 원형 형태로 퇴적된 시료를 대상으로 가열판의 승온속도 $20^{\circ}C/min$의 조건에서 실시하였다. 그 결과, $280^{\circ}C$에서 Zn-Al혼합물 분체는 가열 후 1000 s부터 발열을 통하여 급격히 온도가 상승하여 발화 여부 판단기준이 되는 $450^{\circ}C$를 넘어 $600^{\circ}C$에 다다르며 시간과 함께 감소하였으며 임계 최소발화온도는 $280^{\circ}C$로 나타났다. 퇴적Zn-Al혼합물 분체의 최소발화온도는 문헌에 제시된 Al에 비하여는 낮은 것으로 나타났다.

• Applied Chemistry for Engineering
• /
• v.2 no.2
• /
• pp.147-154
• /
• 1991

Thermogravimetric measurements have been carried out to investigate the stabilization and carbonization of copolymer of acrylonitrile(95 wt %) and methyl acrylate(5 wt %) at various heating rates. The cyclization and dehydrogenation during the stabilization were important factors to determine pore development in the carbonization process. The pore and the specific surface area during the carbonization began to develope at the temperature higher than $400^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.32 no.11
• /
• pp.1227-1232
• /
• 1995

Effect of heating rate on the microstructure of the silicon nitride ceramics has been investigated. The specimens with composition of 92Si3N4-6Y2O3-2Al2O3 (in wt%) were sintered at 176$0^{\circ}C$ under 127 kPa for 3h in N2 atmosphere at various heating rates from 1 to 10$0^{\circ}C$/min. The grain size of larger than 2${\mu}{\textrm}{m}$ and less than 1${\mu}{\textrm}{m}$ were measured and compared for the specimens. Regardless of heating rate, grain size of all the specimens showed bimodal distributions and the fracture toughness remained in the range of 5.53~5.72 MPa.m1/2. However, the aspect ratio of the grains of diameter above 2${\mu}{\textrm}{m}$ increased with the heating rate while their grain size and volume fraction decreased.

• Journal of the Korean Society of Tobacco Science
• /
• v.8 no.1
• /
• pp.41-48
• /
• 1986

This experiment was carries out to study on the effect of temperature raising rate to chemical composition of tobacco leaves during the midrib drying stage of flue-curing. The results were as follows : In the case of the temperature raising rate became more rapidly during midrib drying stage. It had a tendency to increase in oxailic acid, succinlc acid, ammonia, polyphenol; there was a large loss of total sugar, reducing sugar, malic acid, palmitic acid and linolenic acid; leaf color became more reddish; the leaf quality index value decreased, thereby the quality of external appearance deteriorated. It is desirable that the temperature raising rate had to be more slowly.

• Journal of the Korean Ceramic Society
• /
• v.33 no.7
• /
• pp.809-815
• /
• 1996

When Li2O.2SiO2 glass was crystallized between the temperature of maximum nucleation and the temperature of maximum crystal growth it was found that the control of heating rate had serious effect on the crystallinity and microstructure and the greatly changed physical properties. Density and elastic modulus tends to increase but thermal expansion coefficient decreased with increased crystallinity. When heating rate between the tempe-rature of maximum nucleation and the temperature of maximum crystal growth was 10~5$0^{\circ}C$/hr. crystallinity was increased to result in the increment of strength. When nuclation was done at 44$0^{\circ}C$ for 5 hours and the temperature of crystal growth was held at 575$^{\circ}C$ strength was increased until crystallinity reached 65% and strength was decreased with higher crystallinity. These phenomena could be explained that even for the same crystallinity different heat rates resulted in different number and size of cracks.

• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.37-39
• /
• 2001

구리 이온을 함유한 XCuOㆍ(50-X) Na₂Oㆍ50P₂O/sub 5/ 조성을 승온속도 10K/min로 900℃까지 숭온한 후 1시간동안 유지하여 용융하였으며, 연속적으로 가열되어진 흑연판에 부어 급냉함으로써 모유리를 제조하였다. 제조된 유리를 분말상의 시편으로 만들어 상온에서 증류수로 3일동안 용해시켰다. 각각의 조성에 따른 살균효과를 측정하였으며, 제조된 시편을 소지토에 첨가하여 그 항균특성을 관찰하였다. 항균특성 평가를 위하여 사용된 균주는 Staphylococcus aureus 와 Salmonella typhi가 사용되었으며, Staphylococcus aureus 균주에 대해서는 모든 시편 담지후 3시간 이후에, Salmonella typhi에 대해서는 6시간 이후에 모든 균이 소멸되는 것으로 관찰되었다.

• Proceedings of the KAIS Fall Conference
• /
• 2000.10a
• /
• pp.173-177
• /
• 2000

인산염계 5Li₂O, 36CaO, 20TiO₂, 27P₂O/sub 5/의 조성을 선정하여 10K/min 승온속도로 1300℃에서 2시간동안 유지시켜 모유리를 제조하였고, 최적의 핵형성을 위해 610℃에서 20시간, 최고 결정성장을 위해 840℃에서 20시간 동안 열처리함으로써 LiTi₂(PO₄)₃상과 β-Ca₃(PO₄)₂결정상이 존재하는 Glass Ceramics를 제조하였고, 이를 1N-HCI용액에서 3일간 담지하여 β-Ca₃(PO₄)₂결정상을 용출시켜 LiTi₂(PO₄)₃상만이 존재하는 다공성 Glass Ceramics를 제조하였다.