• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.92-96
• /
• 2019

In the presence of ${\mu}-tip$ embedded in a slot-die head for stripe coatings, there arises the capillary flow that limits an increase of the stripe density, which is required for the potential applications in organic light-emitting diode displays. With an attempt to suppress it, we have employed a computational fluid dynamics software and performed simulations by varying the ${\mu}-tip$ length and the contact angles of the head lip and ${\mu}-tip$. We have first demonstrated that such a capillary flow phenomenon (a spread of solution along the head lip) observed experimentally can be reproduced by the computational fluid dynamics software. Through simulations, we have found that stronger capillary flow is observed in the hydrophilic head lip with a smaller contact angle and it is suppressed effectively as the contact angle increases. When the contact angle of the head lip increases from $16^{\circ}$ to $130^{\circ}$, the distance a solution can reach decreases sharply from $256{\mu}m$ to $44{\mu}m$. With increasing contact angle of the ${\mu}-tip$, however, the solution flow along the ${\mu}-tip$ is disturbed and thus the capillary flow phenomenon becomes more severe. If the ${\mu}-tip$ is long, the capillary flow also appears strong due to an increase of flow resistance (electronic-hydraulic analogy). It can be suppressed by reducing the ${\mu}-tip$ length, but not as effectively as reducing the contact angle of the head lip.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.4
• /
• pp.33-38
• /
• 2022

With an attempt to suppress the moiré phenomenon caused by the interference between the black matrix of a display panel and the metal grid of a camera, we have fabricated an anti-moiré filter using light diffusing particles (LDPs) with the average diameter of 20 ㎛. It is demonstrated that the anti-moiré filter coated on a glass substrate (370 mm × 470 mm) using a table slot-die coater reduces the moiré intensity to a great extent when the area covered by LDPs is 50%. To quantify the intensity of moiré phenomenon, we have measured the lightness ratio and found that it is reduced from 132.12 down to 105.71 by the filter. To find the optimum area covered by LDPs, we have performed ray tracing simulations using Mie scatters as a substitute for LDPs. From the simulated irradiation distribution, we have calculated the standard deviation (SD) and contrast ratio (CR) to evaluate the moiré strength. As expected, the SD and CR values decrease with increasing covered area by LDPs. However, there exists a trade-off between the transmittance of the filter and its capability of reducing the moiré intensity in determining the area covered by LDPs.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.4
• /
• pp.32-37
• /
• 2023

For the potential applications in large-area OLED lightings, hydrogen fuel cells, and secondary batteries, we have performed an intermittent coating of high-viscosity polydimethylsiloxane using roll-to-roll slot die coater. During intermittent coating, dead zones inevitably appear where the thickness of PDMS patch films becomes non-uniform, especially at the leading/trailing edge. To reduce it, we have coated the PDMS patches by varying the process parameters such as the installation angle of the slot die head, coating speed, and patch interval. It is observed that the PDMS solution flows down and thus the thickness profile is non-uniform for horizonal intermittent coating, whereas the PDMS solution remaining on the head lip causes an increase in the PDMS thickness at the leading/trailing edges for vertical intermittent coating when the coating velocity is low. As the coating speed increases, however, the dead zone is shown to be reduced. It is addressed that the overall dead zone (the dead zone at the leading edge + the dead zone at the trailing edge) is smaller with horizontal intermittent coating than with vertical intermittent coating.

• Membrane Journal
• /
• v.34 no.1
• /
• pp.79-86
• /
• 2024

The flat sheet membrane, one of the representative forms of polymeric membranes, is widely used from material research in laboratories to commercial membrane production due to its ease of fabrication. Porous polymeric flat sheet membranes used in microfiltration and ultrafiltration are mainly fabricated through phase separation processes, utilizing non-solvent-induced and vapor-induced phase separation methods. However, due to the nature of phase separation processes, variations between samples can easily occur depending on the surrounding environment and the experimenter, making it difficult to ensure reproducibility. Therefore, for scaling up and ensuring reproducibility of developed membrane fabrication technologies, there is a need for a controlled environment continuous large-area production device, such as a roll-to-roll manufacturing system. This research compared the changes in membrane characteristics due to differences in manufacturing environments when scaling up laboratory-scale fabrication technologies to roll-to-roll processes using knife and slot die coaters. By optimizing the continuous manufacturing process factors, uniformity of the membrane was ensured during large-area production.