• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.3
• /
• pp.127-131
• /
• 2003

High quality zincblende ZnTe(100) epilayers have been grown on semi-insulating $CaAs(100\pm2^{\circ})$substrate by hot-wall epitaxy. To grow high quality ZnTe epilayers, the growth temperature dependence of the surface topography, the growth rate, and the crystalline properties were investigated. From the photoluminescence measured at 10 K, the light hole and heavy hole free exciton emissions splitted by thermal tensile strain were observed and their first excited state emissions were also measured. The low temperature doublet of the heavy hole free exciton is because of the energy separation between longitudinal exciton and transverse exciton due to exciton-polariton coupling.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1992.10a
• /
• pp.98-103
• /
• 1992

전세계적인 에너지 절약과 환경보존에 대한 관심과 요구가 증가함에 따라 소비전력규제와 CFC삭감에 대응한 국제경쟁력 확보가 중요한 과제로 대두 되고 있다. 이러한 상황변화에 따라 냉동 공조기기의 심장부인 압축기에 대 해서도 고효율 및 저소음화의 요구가 한층 높아졌다. 따라서 가혹한 환경에 도 견딜 수 있는 압축기의 개발은 필수적이라 할 수 있다. 소형밀폐형 압축 기는 크게 두 부분으로 나뉘어진다. 그 하나는 모터에 의한 회전구동부이고, 다른 하나는 실린더와 피스톤 그리고 밸브로 구성된 압축기구부이다. 그 중 에서 밸브는 진동 및 소음에 영향을 미치는 기본요소가 된다. 압축기의 밸브 는 근본적으로 밸브포트와 실린더 형상에 의해 결정되며, 이런 형상조건하에 서 밸브는 연속적인 운전이 되어야 하므로, 그 응답성이 좋아야 하고 무엇보 다도 자체의 신뢰성도 확보되어야 한다. 따라서 밸브의 동적특성과 응력 분 포를 정확히 예측하는 것이 중요한 과제가 된다. 본 논문에서는 컴퓨터를 이 용한 밸브의 동적특성과 응력해석을 위해 밸브의 형상을 유한요소 패키지인 ANSYS를 이용하여 해석하고, 그 모델링 및 해석이 타당성을 검토하기 위하 여 동적 특성해석은 홀로그래피(Holography) 기술을 이용하여 실험하고, 응 력해석은 스트레인 게이지(strain gage)를 이용하여 결과를 얻어서 서로 비 교하여 보았다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.2
• /
• pp.116-123
• /
• 2002

Applying a general coupled lateral and torsional vibration finite element model of gear pair element, this paper intends to look into in detail the coupled lateral and torsional vibration characteristics of a turbo-chiller rotor bearing system, having a bull-pinion speed increasing gear. Investigations have been carried out systematically by comparing the uncoupled and coupled natural frequencies and their mode shapes upon varying the gear mesh stiffness with considerations on rotating speeds, and also by comparing the strain energies of lateral and torsional vibration modes. Results hale shown that some modes may hale the coupled lateral and torsional mode characteristics as the gear mesh stiffness Increases over a certain value, and moreover that their associated dominant modes may be different from their initial modes, j.e., a certain dominant mode may change from an initial torsional one to a lateral one or from an initial lateral one to a torsional one.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.834-837
• /
• 2005

Structural Dynamics Modification (SDM) is a very effective technique to improve structure's dynamic characteristics by adding or removing auxiliary structures, changing material properties and shape of structure. Among those of SDM technique, the method to change shape of structure has been mostly relied on engineer's experience and trial-and-error process which are very time consuming. In order to develop a systematic method to change structure shape, surface grooving technique is studied and successfully applied to HDD cover model. At first, to check the effect of mesh size, surface grooving technique was tested to the fine HDD cover FEmodel. And fur the more efficient method, the algorithm is modified. Removing the low-valued modal strain energy element among the target domain, computational effort can be greatly reduced and the result of simulation is similar with the other simulation result.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.287-292
• /
• 2011

To evaluate the pressure-resistant performance of underwater equipment, hyperbaric chamber test facility which can make the hydrostatic pressure is used. In this test, strain gage is generally applied to measure the strain of object under test is suitable for measuring a tiny deformation, but it can not measure a large deformation. Thus this paper suggests a method to estimate the over -order deformation of object under test by the image processing with the image acquired from underwater camera in the hydrostatic test. The main procedure of suggested method comprises the first step to find significant points by processing the image two dimensionally and the second step to estimate a deformation of object under test by tracking the motion of these points. If completing the remained research which is estimating the deformation and comparing it with a real one, it can be a method to measure the over -order deformation of object under test.

• Composites Research
• /
• v.22 no.4
• /
• pp.33-40
• /
• 2009

Fiber orientation effects on the impact surface fracture of the glass plates coated with the glass fiber/epoxy lamina layer were investigated using a small-diameter steel-ball impact experiment. Four kinds of materials were used: soda-lime glass plates, unidirectional glass fiber/epoxy layer(one ply, two plies)-coated, crossed glass tiber/epoxy layer (two plies)-coated glass plates. The maximum stress and absorbed fracture energy were measured on the back surface of glass plates during the impact. With increasing impact velocity, various surface cracks such as ring, cone, radial and lateral cracks appeared near the impacted site of glass plates. Cracks in the plate drastically diminished by glass fiber coating. The tiber orientation guided the directions of delamination and plastic deformation zones between the tiber layer and the glass plate. Impact surface-fracture indices expressed in terms of the maximum stress and absorbed energy could be used as an effective evaluation parameter of the surface resistance.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.133-137
• /
• 2001

The method to make glass is tried first thing in domestic study for glasses lens. Tg of glass KzFSl was measured by DSC experiment and press method of glass of meniscus shape was studied for minimize the cost. Tg was increased $483^{\circ}C$ to $501^{\circ}C$ with increasing heating rate $2^{\circ}C/min$ to $20^{\circ}C/min$. It shows Arrhenius temperature dependence and the activation energy of Tg is ${\Delta}E$=409 kJ/mole(4.25eV) by using Ozawa method and Tg is near $480^{\circ}C$. The melt of KzFSl powder was poured to concave cast stainless and pressed convex cast stainless. The quenched glass was slow cooled with cooling rate $0.25^{\circ}C/min$ in temperature range $520{\sim}430^{\circ}C$. The glass was made without strain. It has meniscus shape and same size to commercial glasses lens.

• Composites Research
• /
• v.18 no.1
• /
• pp.45-54
• /
• 2005

The delamination in the filament-wound composite flywheel rotor often lowers the performance of the flywheel energy storage system. A conventional ring type hub usually causes tensile stresses on the inner surface of the composite rotor, resulting in lowering the maximum rotational speed of the rotor. In this work, the stress and strain distributions within a hybrid composite rotor were derived from the two-dimensional governing equation with the specified boundary conditions, and an optimum pressure at the inner surface of the rotor was proposed to minimize the strength ratio and maximize the storage energy. A split type hub was introduced to apply the calculated optimum pressure at the inner surface, and a spin test was performed up to 40,000 rpm to demonstrate the performance of the split type hub with radial and circumferential strains measured using a wireless telemetry system. From the analysis and the test, it was found that the split type hub successfully generates a compressive pressure on the inner surface of the rotor, which can enhance the performance of the composite rotor by lowering the strength ratio within the rotor.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2007

As fiber reinforced composite materials are widely used in aircraft, space structures and robot arms, the study on non-destructive testing methods has become an important research area for improving their reliability and safety. AE (acoustic emission) can evaluate the defects by detecting the emitting strain energy when elastic waves are generated by the initiation and growth of crack, plastic deformation, fiber breakage, matrix cleavage, or delamination. In the paper, AE signals generated under uniaxial tension were measured and analyzed using the $8{\times}8$ matrix piezo electric sensor. The electronic circuit to control the transmitting distance of AE signals was designed and constructed. The optical data storage system was also designed to store the AE signal of 64channels using LED (light emitting diode) elements. From the tests, it was shown that the source location and propagation path of AE signals in composite materials could be detected effectively by the $8{\times}8$ matrix piezo electric sensor.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.92-97
• /
• 2000

Low-velocity impact damage of a thick pressure vessel by composite materials was studied using the modified Herzian contact radius theory. Impactors of various masses and various tup shapes were dropped freely in the range of 20m to 200mm height. With acceleration gage and strain gage installed on the impactor, impact force and acceleration and Contact radius were measured. After a test, the samples were radiographed to scan the state of damage. Compared with hemispherical tup of 12.7mm diameter, the contact radius of hemispherical tup of 25.4mm diameter was bigger. And the experimental data and the theoretical data was different due to the mechanical properties difference. The acceleration value was changed linearly according to the height.