• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.459-465
• /
• 2004

The present paper is intended to investigate the influence of materials such as cement, mineral admixture and aggregate, on the estimation of compressive strength by P type schmidt hammer. According to the results, the materials of concrete, such as the types of cement, the replacing ratio of mineral admixture, the kinds and maximum size of aggregate, hardly influence on non-destructive test by P type schmidt hammer except for alumina cement, hence, P type schmidt can be applicable to most of the concrete with a wide range. Since the correlativity between the rebound value of P type schmidt hammer and compressive strength is very favorable(above coefficient of correlation 0.96) regardless of materials, it is considered that compressive strength can be estimated comparatively exactly by P type schmidt hammer. The estimating formula of compressive strength by rebound value are derived from this experiment as following. $\cdot$Horizontal strike : Fc = 0.765RH - 5.74 (R=0.965) $\cdot$ Vertical strike Fc = 0.793RV - 8.66 (R=0.959)

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.3
• /
• pp.199-207
• /
• 2008

As infrastructures are being deteriorated, nondestructive evaluation of existing structures and construction quality control are increasingly demanded. The importance of predicting compressive strength of concrete structure is also gradually increasing in construction industry. The estimation of concrete compressive strength is a critical factor of the construction management and quality control. This study has been conducted using Schmidt hammer test and Impact echo method, which are nondestructive test methods for the comparison of the concrete compressive strength. It is focusing to examine the relationship between compressive strength of concrete and rebound number by Schmidt hammer test result by Impact echo method. It was found that concrete compressive strength and rebound number have a close correlation.

• Journal of the Korean Geosynthetics Society
• /
• v.7 no.1
• /
• pp.13-21
• /
• 2008

To investigate the engineering properties of basalt in Cheju Island, rock samples of Pyosenri basalt, trachy-basalt and scoria were taken from Seoguipo-Si Seongsan-Eup area. The laboratory tests such as absorption test, specific gravity test, permeability test, Schmidt hammer test, elastic wave test and uniaxial compressive testwere carried out for the collected rock samples. The absorption, the specific gravity, the permeability, the elastic wave velocity and uniaxial compressive strengthwere investigated and analyzed as the results of these tests. As the result of regression analysis for the relationship between the rebound values from Schmidt hammer test and the uniaxial compressive strengths from uniaxial compressive test, especially, estimation equations were proposed using the rebound values from Schmidt hammer test. Therefore, the simple method to estimate the uniaxial compressive strength was provided.

• Proceedings of the KSEEG Conference
• /
• 2007.04a
• /
• pp.643-645
• /
• 2007

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.5-17
• /
• 2000

The physical and mechanical properties of the sedimentary rocks deposited in Taegu and Kyongbuk region have been measured in the laboratory and at the field. Four kinds of rocks such as the shale, the mudstone, the siltstone and the sandstone were the object of this study. In sedimentary rock joint, bedding made it impossible to extract cores for uniaxial compressive test. Some correlations between the uniaxial compressive strength and the other characteristic values such as Point load index, Schmidt hammer rebound, Brazilian strength, P-wave velocity and Absorption ratio are made. The chemical and mineral compositions are also investigated by the XRF and XRD analysis. In addition, the weathering grade of rocks are classified by the quantitative indices of Point load index, Schmidt hammer rebound and Absorption ratio.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.615-618
• /
• 2005

This study concerns the equation of high strength concrete by schmidt hammer test. There are not only few prediction strength equations of concrete by schmidt hammer test, but also many problems to apply them because of time, cost, easiness, structural damage, reliability and so on. For this study, there performed a series of schmidt hammer test with in existing 1,095days' concrete structures and proposed equations as follows ; Linear: ${\Large f}_{ck}=-45.35+2.44R(r^2=72.7\%)$ Quadratic: ${\Large f}_{ck}=-502.08+24.0R-0.25R^2(r^2=82.4\%)$ here, $f_{ck}$ : Estimated compressive strength of concrete by MPa, R : Rebound index of concrete

• Journal of the Korea Concrete Institute
• /
• v.16 no.3 s.81
• /
• pp.327-334
• /
• 2004

In this paper, method for the determination of removal time of the side forms in high strength concrete are discussed using the estimation model of compressive strength development, the development of bond strength and rebound number of P type Schmidt hammer in order to review the validity of existing regulation as to side form removal and offer effective quality control method. According to the results, as W/B increases by $10\%$, the setting time is shortened by about 2 hours. In the scope of the paper, required time to gain 8MPa of compressive strength is determined about 17 ${\~}$20 hours of age and $21{\~}25^{\circ}D{\cdot}D$ of maturity. Bond strength between form and concrete shows the highest value around final setting time, but decreases drastically after that. Amount of concrete sticking on the form is large before setting completed, but after that, its amount shows decline tendency. The rebound value test with P type schmidt hammer can be started faster by 2${\~}$3 hours than compressive strength test. It is also confirmed that the removal of forms is possible when the rebound value of P type schmidt hammer is more than 32. It is found from the results that existing regulation regarding removal time of the side form of high strength concrete provided in KCI needs no revision because required time to gain the strength provided in KCI has no adverse effect on strength development at early age and surface condition during stripping the side form. Effective procedure to decide the removal time of side form can be performed by applying P type Schmidt hammer.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.341-348
• /
• 2016

Harbor facilities require long-term durability and safety, and also maintain the performance requirement until the durability life. However, existing harbor facilities are becoming superannuated with durable years and durability is declined by erosion of the sea and damage from sea. In addition, harbor facilities will be in demand for the expansion of harbor and offshore structures with rising economic power by enhancement of domestic industry and increase of import and export. Therefore, in this study, two kinds of nondestructive test (NDT) techniques (schmidt rebound hammer and ultrasonic sensor) are verified for the effective maintenance of underwater concrete structures including harbor facilities. Sea field applicability of Schmidt hammer and ultrasonic sensor was verified by comparing field test result with sea field test result and also deduced the compressive strength estimation equation by depth of the water. On the basis of the sea field test result, compressive strength estimation equation which was deduced by multiple regression analysis indicated highest accuracy compared to other equations, especially it will be more likely to be used in underwater because of the depth of water correction. In the future, if schmidt hammer and ultrasonic sensor which were invented as waterproofing are used with ROV (Remotely Operated Vehicle), it will be possible to make a diagnosis of high reliability for underwater concrete structures and set up a ubiquitous concept of NDT system.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.3
• /
• pp.229-237
• /
• 2019

This study examines the estimation of strength through a ultra-high strength concrete mock-up specimen using the rock compressive strength test hammer. According to the test result, the commonly used strength estimation formulae showed differences among them when the data of this test were applied. In additional, it show that these formulae underestimated the actual measurements further when the compressive strength was 30MPa or greater and deviated the distribution range of actual measurements in all strength ranges. The rock test hammer showed a higher correlation than type N Schmidt hammer regardless of the direction of hit for each type of W/B and the inclusion of coarse aggregate, and mortar showed a little higher correlation than concrete. As a result, it can be suggested that the coefficient of variation and the standard deviation of the mortar(2.26%/1.36) are lower than those of the concrete(4.06%/2.5), and the smaller the size of the coarse aggregate, the smaller the coefficient of variation and the more accurate the value.

• Journal of the Korea Concrete Institute
• /
• v.17 no.3 s.87
• /
• pp.313-322
• /
• 2005

Recently, as the remodeling market gradually substitute for new construction market and safety diagnosis for reconstruction apartment become a matter of principal Interest, it is demanded that scientific diagnosis and evaluation for existing concrete structure state. And it is increasing that the significance for reliability of data which is used for estimating the concrete compressive strength by nondestructive test. As a result, it is found that different proposal to material age and hitting angle is good to improving the reliability of presumption of concrete compressive strength in the linear hitting rebound test hammer. And for the reason that mutual relation between the compressive strength and rebound degree is highest in linear hitting rebound test hammer 25mm in all portion according to early md middle material age and hitting angle except the early material age $-45^{\circ}$, analysis showed that linear hitting rebound test hammer is more reliable than existing schmidt hammer in presumption of concrete compressive strength.