• Resources Recycling
• /
• v.27 no.3
• /
• pp.58-65
• /
• 2018

For the recycling of coal ash from the domestic circulating fluidized bed boilers, a lime-based sorbent with 0.2~0.4 mm size was prepared by using limestone powder and CFBC fly ash. Mixing a small amount of slaked lime in the lime-based absorbent lead the formation of calcium silicate on the surface of the particle and the strength of absorbent particle was improved. As a result of comparing the desulfurization characteristics, it was found that the conversion rate was about 10% higher than that of commercially available limestone desulfurization used in the furnace, which is confirmed that it can be used as a desulfurization absorbent.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.492-500
• /
• 2019

In this study, the effect of chemical additives on the reduction of fine particles was identified in $9.2MW_e$ commercial scale circulating fluidized bed boiler firing bituminous coal. Futhermore, a simple and effective method of fine particle collection has been developed to collect the fine particles of the boiler during fossil fuel combustion. Chemical additives were used to reduce particles below 10 PM in the flue gas, and borax solution was used as a chemical additive. In order to identify the particle behavior of PM 10 or less among the collected fine particles, it was analyzed through particle size analyzer and SEM analysis. The Borax solution tends to absorb molten mineral in the flue gas and make fine particles grow. As a result, it was analyzed that particles smaller than $10{\mu}m$ were reduced by using borax solution.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.443-450
• /
• 2021

The effects of blast furnace slag(BFS) and desulfurized gypsum(FDG) on the compressive strength of CFBA, and self-hydration of CFBA were studied. CFBA has self-hydrating and hardening properties, and it can be seen that the compressive strength of CFBA can be improved by using appropriate amounts of BFS and FDG. In addition, the self-hardening properties of CFBA are similar to the hydration reaction of 4CaO·Al₂O₃·Fe₂O₃ (C₄AF), a cement clinker mineral, and when free-CaO, CaSO₄ and CaCO₃ coexist, Compressive strength of CFBA is expressed by the formation of calcium carbo compounds and hydrates of ettringite, calcium silicate, and calcium aluminate.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.145-148
• /
• 2008

Fuel flexibility of CFBC boiler was examined. Combustion characteristics of low grade coal, coal sludge, coal RDF mixture and RDF were compared. The operation result of a commercial 130TPH CFBC co-generation boiler burning a low grade Chinese coal were analysed. Burning characteristics of coal/RDF mixture and coal and industrial sludge mixture were studied in a 0.1MWth scale CFBC test rig. Also RDF fuel were tested in a 8TPH CFBC test facility. Though fuel characteristics were different, the combustion modes were all very stable. The temperature were maintained in between $800-950^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1998.07b
• /
• pp.722-724
• /
• 1998

One of the major concerns of our time is the need to use energy economically and rationally while at the same time, protecting the environment. Circulating Fluidized Bed(CFB) Boilers represent a proven, very attractive clean coal technology, with the added advantage of an unusual fuel flexibility CFB boiler is the best available compromise between cost and environment for fossil fuel power plant. This paper briefly describes CFB process and 200MW CFB boiler for Tonghae power plant. Also, discussed are differences between the control process of fluidized bed and conventional boilers, and applied control process for Tonghae power plant.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.259-261
• /
• 2007

논문은 동해화력발전처의 이차공기송풍기를 가변 회전수 제어하여 소내 소비 전력을 절감하고 전동기의 직입기동에 의한 스트레스를 줄이기 위하여 실증 적용된 동해화력발전처 이차 공기 송풍기 구동용 H-브릿지 멀티레벨 인버터에 관한 것이다. H-브릿지 멀티레벨 인버터는 독립적으로 절연된 직류 부를 갖는 저압의 단상 인버터(셀 인버터)를 다수 직렬 접속하여 고압 3상 전압을 출력하는 Cascaded H-브릿지 전압형 인버터이다. 본 논문에서는 동해화력발전처에 실증 적용된 6.6kV, 1MVA급 인버터의 계통 병입 후 부하 변동 시험을 통하여 신뢰성을 입증하였다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.135-136
• /
• 2019

Recently, as the interest in environmental issues increases, the construction industry needs to recycle blast furnace slag, circulating fluidized bed Combustion fly ash, etc. to solve industrial by-products, and to develop artificial stone. In this study, the strength characteristics based on blast furnace slag according to the addition rate of alkali stimulant NaOH are investigated. The experimental results showed that the flexural and compressive strengths increased with the addition of alkali stimulants. Based on these results, it will be presented as a basic research data for the manufacture of artificial stone and will be tested later.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.1
• /
• pp.8-16
• /
• 2020

As the circulating fluidized bed combustor(CFBC) boilers system to generate electric power increase in order to reduce environmental pollution, a lot of CFBC fly ashes(CFFA) are produced. CFFA has limited use in concrete because it contains free CaO, which can cause cement expansion and rapid initial hydration. In this study, the microstructure and the initial development of compressive strength characteristics were experimentally analyzed to be used as a stimulant to replace natural gypsum by mixing with CFFA and phosphate gypsum to enhance the initial strength of portland blast furnace slag cement. The recycled gypsum was used as flue-gas desulfurization gypsum and phosphate gypsum. Experimental results show that the initial strength development is relatively lower when CFFA and dihydrate gypsum are mixed, but the strength improvement effect of the mixture with CFFA and anhydrous gypsum as an anhydritedII typed crystalized gypsum is similar to that of natural gypsum. As a result, it w as analyzed to have high possibility of use for stimulant of portland blast furnace slag cement.

• Plant Journal
• /
• v.6 no.2
• /
• pp.70-77
• /
• 2010

This study investigated the characteristics of co-combustion of mixed anthracite (domestic and Vietnam) and bituminous coal (Sonoma, Australia) at circulating fluidized bed boiler in Donghae thermal power plant when mixing ratio of bituminous coal is variable. Co-combustion of bituminous coal contributes to improvement in general combustion characteristics such as moderately retaining temperature of furnace and recycle loop, reducing unburned carbon powder, and reducing discharge concentration of NOx and limestone supply owing to improvement in anthracite combustibility as the mixing ratio was increased. However, bed materials were needed to be added externally when the mixing ratio exceeded 40% because of reduction in generating bed materials based on reduction in ash production. When co-combustion was conducted in the section of 40 to 60% in the mixing ratio while the supplied particles of bituminous coal was increased from 6 mm to 10 mm, continuous operation was shown to be possible with upper differential pressure of 100 mmH2O (0.98 kPa) and more without addition of bed materials for the co-combustion of mixed anthracite and bituminous coal (to 50% or less of the ratio) and that of domestic coal and bituminous coal (to 60% of the ratio).

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.37-43
• /
• 2019

This research studied production of lightweight filling production for sink hole restoration utilizing various industrial by-products(2kinds of fly ash, petro-cokes CFBC ash, blast furnace slag fine particle). For this purpose, the mixed raw material properties(compressive strength) behaviors according to the blending ratio of industrial by-products were examined by applying the experimental design method and statistical analysis was performed using the commercial program MINITAB. Compressive strengths of industrial by-products were strongly dependent on blast furnace slag powder. Compressive strength(3days aging) was 3~11MPa depending on the amount of blast furnace slag powder used. The use of CFBC fly ash was evaluated to have the least effect on compressive strength. In addition, the compressive strength and the coefficient of permeability were measured by preparing foamed concrete for the experimental batch 1 condition in the mixture experimental design. In this case, the bulk density is 0.9 to 1.0, the apparent porosity is 30 to 50%, the compressive strength(3days old) is 1 to 2MPa, and the permeability coefficient is $10^{-2}$ to $10^{-3}cm/sec$.