• Korean Journal of Food Science and Technology
• /
• v.32 no.6
• /
• pp.1313-1318
• /
• 2000

총고형분 함량$(TS:\;50{\sim}57%)$을 달리하여 숙성시킨 고추장의 유동특성, 정적 및 동적점탄특성을 관찰하였다. 고추장의 TS가 증가함에 따라서 점조도 지수(K)와 겉보기 점도$({\eta}_{a.5})$는 증가하였으며 유동성 지수(n)는 1보다 훨씬 낮은 0.24-0.31의 범위를 나타내어 고추장은 shear-thinning 성질을 보여주었다. 고추장의 항복응력 측정에서는 고추장의 TS가 증가함에 따라 Casson 항복응력$({\sigma}_{oc})$은 증가하는 경향을 나타내었으며, 또한 고추장의 액상 매개체인 serum 점도$({\eta}_{se})$는 고추장의 TS와 매우 좋은 상관관계$(R^2=0.97)$를 나타내었다. 고추장의 동적점탄성 실험에서는 주파수$({\omega})$가 증가함에 따라 저장탄성률(G#)와 손실탄성률(G@)은 증가하였으며 양(+) 기울기로 G#수치가 G@수치보다 높게 나타났다. 이는 고추장이 약한 겔과 같은 구조적 특성을 갖고 있으며 또한 shear-thinning 거동을 가지고 있음을 나타낸다. 정적점탄성 실험에서 고추장의 총고형분 함량에 따라서 순간탄성 변형$(J_0)$과 지연탄성변형$(J_1)$은 총고형분 함량이 증가함에 따라서 감소하였으며 점도$({\eta}_N)$와 지연시간 $({\tau}_1)$은 증가하였다. 따라서 고추장은 농도가 증가함에 따라 보다 탄력적이며 안정된 구조를 형성하고 있음을 알 수 있었다.

• Journal of Power System Engineering
• /
• v.22 no.6
• /
• pp.28-35
• /
• 2018

The large-eddy simulation (LES) was carried out to evaluate the instantaneous vector and vorticity profiles of a small-size axial fan (SSAF) at the operating point of full-flowrate. The downstream flow of the SSAF exhibits a shorter axial flow when not fully developed, especially the stronger vortex appears at the edge near the flow end. On the other hand, the downstream flow of the SSAF exhibits a longer axial flow, and the weaker vortex appears at the edge near the flow end when the flow is sufficiently developed. Moreover, in the downstream of the SSAF, a periodic and intermittent flow pattern appears at the edge showing the axial flow, and the instantaneous vorticity contour lines showing the form of a circle group are distributed at specific intervals from the downstream region of the blade tip, which is considered to be the result of the intermittency phenomenon influenced by the number of blades and the number of revolutions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.180-186
• /
• 2012

A water-flow test for acceptance verification is carried out for a nonimpinging-type injector prior to the design-performance verification of 70 N-class liquid-rocket engine under development. It is observed that there exist varying characteristics of atomization among the injector-orifices caused by a fabrication crudeness of orifice holes which can be judged from a microscopic standpoint. The flow shedding phenomenon and ruffle on the surface of liquid column (or droplet) could be caught from the instantaneous spray images.

• 한국해양학회지
• /
• v.30 no.5
• /
• pp.467-479
• /
• 1995

To investigate the current structures and diffusion characteristics in Youngil Bay, a systematic field observations of current velocity, drogue tracking, dye diffusion experiment and aerial photographing were performed. The flow patterns in the surface layer of the bay depend more strongly on the wind and ocean current than the tidal current, and the patterns in the middle are predominated by the ocean current. The residual currents in the surface generally flow toward the inner bay through the western and central areas of the bay, and then the currents go toward the ocean along the eastern shore of the bay with anti-clock-wise circulation. The residual currents in the surface of the eastern cease are not nearly influenced by the wind, and the currents always move northward to northeastward. However, the currents in the western shore depend strongly on the wind and the outflow of the Huntsman River, that is, the residual currents go northward to northeastward when the southerly to westerly winds blow or a large amount of flow from the river discharge. The residual currents in the middle layer flow toward the inner bay along the western shore of the bay, and the incomed currents go out to the ocean along the eastern shore with anticlockwise circulation. The diffusion of dye patch by the instantaneous point source shows a similar pattern to the drogue trajectory, and the apparent diffusion coefficients of the dye patch by Fick's theory is 1.14${\times}$10$^4$ cm$^2$/s. The behavior of the river discharges in flood shows a band type's effluent pattern toward the outer bay along the western coast.

• The Journal of Engineering Geology
• /
• v.16 no.4 s.50
• /
• pp.411-427
• /
• 2006

This study aimed to recognize characteristics of groundwater flow in fractured bedrocks based on zonal pump-ing tests, slug tests, water quality logs and borehole TV camera logs conducted on two boreholes (NJ-11 and SJ-8) in the city of Naju. Especially, the zonal pumping tests using sin91e Packer were executed to reveal groundwater flow characteristics in the fractured bedrocks with depth. On borehole NJ-11, the zonal pumping tests resulted in a flow dimension of 1.6 with a packer depth of 56.9 meters. It also resulted in lower flow dimensions as moving to shallower packer depths, reaching a flow dimension of 1 at a 24 meter packer depth. This fact indicates that uniform permissive fractures take place in deeper zones at the borehole. On borehole SJ-8, a flow dimension of 1.7 was determined at the deepest packer level (50 m). Next, a dimension of 1.8 was obtained at 32 meters of packer depth, and lastly a dimension of 1.4 at 19 meters of packer depth. The variation of flow dimension with different packer depths is interpreted by the variability of permissive fractures with depth. Zonal pumping tests led to the utilization of the Moench (1984) dual-porosity model because hydraulic characteristics in the test holes were most suitable to the fractured bedrocks. Water quality logs displayed a tendency to increase geothermal temperature, to increase pH and to decrease dissolved oxygen. In addition, there was an increasing tendency towards electrical conductance and a decreasing tendency towards dissolved oxygen at most fracture zones.

• Tunnel and Underground Space
• /
• v.11 no.4
• /
• pp.319-327
• /
• 2001

Introduction of new design tools has been required to optimally design and operate the ventilation system of long vehicle tunnels.. The demand has led to wide spread use of the simulation technique throughout the would to analysis the dynamic relationship among the variables associated with vehicle tunnel ventilation. This paper aims at performing on-site study at local tunnels to test the applicability of NETVEN, a simulation model vehicle tunnel ventilation. The study was carried out at four urban as well as highway tunnels model of vehicle tunnel ventilation. The study was carried out at four urban as well as highway tunnels employing different ventilation systems as well as traffic methods. There were some discrepancies sound between the simulation output and measurements and the following four factors are considered to mainly cause those disagreement. (1) The real situation shows distinctive transient and retarding characteristics with respect to air flow and contaminant dispersion, while ventilation forces are not steady-state and in particular those traffic and climatic variables show significant instantaneous variation. (3) Near the exit portal, the CO levels show bigger differences. The general trend is that data with higher CO concentrations carry bigger discrepancies. Turbulent diffusion is though to be the main reason for it and also contribute to the fact hat the highest CO concentrations are found at the locations somewhat inward, not at the exit portals. (4) Higher traffic rate results in higher discrepancies of ventilation velocity. Along with the exhaust characteristics, the vehicle aerodynamic characteristics need to be studied continuously in order to reduce the velocity disagreement.

• Journal of Bio-Environment Control
• /
• v.14 no.3
• /
• pp.166-173
• /
• 2005

This study was carried out to evaluate the structural stability in a non-heating greenhouse with a single cover for Citrus cultivation which was built up in Jeju on the basis of the drawing designed by Jejudo Agricultural Research & Extension Services and also to make use of the data for developing a standardized non-heating greenhouse in Jeju. The analysis of a structural stability was conducted by using CFX-5.7 and ANSYS under the design condition of a maximum accumulated snow-depth of 19.1 cm as well as an instantaneous maximum wind velocity of $36.6\;m{\cdot}s^{-1}$ which was set up on the basis of meteorological statistics in Jeju. As a result, the maximum von-Mises stress applied on pipes under the wind velocity of $36.6\;m{\cdot}s^{-1}$ showed a value of $250\;N{\cdot}mm^{-2}$ which was greater than the allowable stress of the pipe with a value of $235.4\;N{\cdot}mm^{-2}$ (=$2,400\;kg{\cdot}cm^{-2}$) and also $53.8\;N{\cdot}mm^{-2}$ under the snow-depth of 19.1 cm, respectively. This result suggested that the greenhouse be unstable under the design condition of an instantaneous wind velocity of $36.6\;m{\cdot}s^{-1}$ so that it was necessary for the greenhouse to be reinforced to secure the structural stability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.9
• /
• pp.799-804
• /
• 2007

The behavior of spray emanating from an injector to be employed in a liquid-propellant thrust chamber is investigated by optical measurement techniques. The injector has eight holes, each of which has 30 cant angle from the center-axis with the diameter of 0.406 mm. In order to examine an atomization process according to the spray-generation conditions and the evolution along spray downstream, variational features in the velocity and size of droplets obtained through Dual-mode Phase Doppler An 799emometry (DPDA) are delineated and discussed together with instantaneous plane images captured by using Nd:Yag laser sheet beam. A categorization of spray-flow regime representing the atomization and turbulent nature is made through evaluating the non-dimensional parameters, i.e., Reynolds number and Weber number based upon the theoretical injection velocity. These qualitative and quantitative data of spray breakup will be a firm basis for the design of brand-new thruster

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.69-69
• /
• 2010

최근 컨테이너 선박의 초대형화로 극후물 고장력 강재인 항복응력 460MPa급 고장력강인 EH47이 개발되었다. 두께 80mm의 극후물 용접에서 용접생산성 향상을 위하여 EGW/FCAW로 양면 용접이 검토되고, 입열량은 최대 300kJ/cm의 대입열 용접이 요구된다. 이를 위해서는 강재 및 용접재료 모두 300kJ/cm 용접부 성능이 선급 규격을 만족하여야 함은 물론 마지막 조립단계에서 적용되기 때문에 용접재료의 용접작업성도 매우 크게 요구되고 있다. 먼저 대입열 용접금속에서 요구되는 저온 충격인성($vE_{-20^{\circ}C}{\geq}57J$)을 만족하기 위하여는 용접금속의 미세조직 제어가 필요하며, 특히 조대한 입계페라이트 생성을 억제하고 미세한 입내 페라이트를 균일 분포하는 것이 중요하지만, 이를 위해 용접금속의 소입성이 지나치게 높이면 경화조직인 베이나이트 분율이 증가하여 오히려 용접금속 저온 충격인성을 저하시키므로, 적절한 용접금속의 성분 제어가 중요하다. 한편 용접부는 선급에서 요구하는 최소 강도인 570MPa를 만족하기 위하여 용접금속의 소성구속 현상을 활용하여 용접부 인장강도를 확보 할 수 있음을 확인했다. 이를 위해서는 용접금속의 적정한 경화도 확보가 필요하였다. 전술한 바와 같이 대입열 용접금속 저온 충격인성 확보와 용접부 강도 측면을 고려하여 용접금속 최적의 탄소당량 범위를 제시코자 하였다. 한편 용접재료의 용접작업성은 EGW용접의 용적이행 현상은 자유비행이행으로 이루어지고 있으며 특성상 용접중 용적과 용융지 사이에 많은 순간단락 현상을 동반하고 있으며, 슬래그 유동이 불안정하면 아크 꺼짐 현상도 관찰되고 있다. 따라서, 현장용접시 원할한 용접작업성을 확보할 수 있는 평가 기준으로써 아크 전류 및 전압의 변동 정도를 설정하고, 용접재료의 용접작업성 확보 기준을 제시코자 하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.15-28
• /
• 1998

As an alternative for solving the incompressible Navier-Stokes equations, we present a vorticity-based integro-differential formulation for vorticity, velocity and pressure variables. One of the most difficult problems encountered in the vorticity-based methods is the introduction of the proper value-value of vorticity or vorticity flux at the solid surface. A practical computational technique toward solving this problem is presented in connection with the coupling between the vorticity and the pressure boundary conditions. Numerical schemes based on an iterative procedure are employed to solve the governing equations with the boundary conditions for the three variables. A finite volume method is implemented to integrate the vorticity transport equation with the dynamic vorticity boundary condition . The velocity field is obtained by using the Biot-Savart integral derived from the mathematical vector identity. Green's scalar identity is used to solve the total pressure in an integral approach similar to the surface panel methods which have been well-established for potential flow analysis. The calculated results with the present mettled for two test problems are compared with data from the literature in order for its validation. The first test problem is one for the two-dimensional square cavity flow driven by shear on the top lid. Two cases are considered here: (i) one driven both by the specified non-uniform shear on the top lid and by the specified body forces acting through the cavity region, for which we find the exact solution, and (ii) one of the classical type (i.e., driven only by uniform shear). Secondly, the present mettled is applied to deal with the early development of the flow around an impulsively started circular cylinder.