• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.4
• /
• pp.469-480
• /
• 2022

To design the crown wall of rubble-mound breakwaters, the horizontal wave load should be available, but determining this load remains difficult. Lee et al. proposed modification factors for Goda's formula for the horizontal wave pressures on acrown wall. The empirical formula by Lee et al. was based on a two-dimensional model test with a relatively narrow armour crest width in front of the crown wall. In this study, a series of experiments at the same facility were conducted on the horizontal wave pressures on the crown wall of a rubble-mound breakwater with a wide armour crest width. As a result, the pressures of the unprotected part of the crown wall were nearly identical to the narrow crest width. However, the pressures of the protected part tended to decrease with a change in the armour crest width. From the experimental results, the horizontal pressure modification factors of Goda's formula including the armour crest width effect are suggested here and are likely applicable to practical designs of the crown walls of rubble-mound breakwaters covered with tetrapods.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.6
• /
• pp.321-332
• /
• 2021

The crown wall with parapet on top of the rubble mound breakwater represents a relatively economic and efficient solution to reduce the wave overtopping discharge. However, the inclusion of parapet leads to increased wave pressure on the crown wall. The wave pressure on the crown wall is investigated by physical model test. To design the crown wall the wave loads should be available, and the horizontal wave pressure is still unclear. Regarding to the horizontal wave pressure on the crown wall, a series of experiments were conducted by changing the rubble mound type structure and the wave conditions. Based on these results, pressure modification factors of Goda's (1974, 2010) formula have been suggested, which can be applicable for the practical design of the crown wall of the rubble-mound breakwater covered by tetrapods.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.6
• /
• pp.363-368
• /
• 2017

The tsunami flood the coastal cities and damage the land structures. The study on wave pressure and force on land structures is one of the important factors in designing the stability of inland structures. In this study, two - dimensional wave flume tests on the horizontal wave force and pressure of tsunamis on a simplified box-type structure was conducted. Vertical distribution and wave power of horizontal wave pressure over time were measured by pressure sensors and force transducer. Also, those were measured from the different wave breaking types. The vertical distribution of horizontal wave pressure was uniform at the moment when the horizontal wave force to the structure was maximum under the breaking wave condition. A surf similarity parameter was employed in order to figure out the relationship between the maximum horizontal wave force on the structure as a function of various incident wave conditions. As a result, the non - dimensionalized horizontal wave force tends to decrease exponentially as the surf similarity parameter increases.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.3
• /
• pp.180-201
• /
• 2020

It has been widely known that the effect of diffracted waves at the tip of composite breakwater with finite length causes the change of standing wave height along the length of breakwater, the spatial change of wave pressure on caisson, and the occurrence of meandering damage on the different sliding distance in sequence. It is hard to deal with the spatial change of wave force on trunk of breakwater through the two-dimensional experiment and/or numerical analysis. In this study, two and three-dimensional numerical techniques with olaFlow model are used to approach the spatial change of wave force including the impulsive breaking wave pressure applied to trunk of breakwater, the effect of rear region, and the occurrence of diffracted waves at the tip of caisson located on the high crested rubble mound. In addition, it is thoroughly studied the mean wave height, mean horizontal velocity, and mean turbulent kinetic energy through the numerical analysis. In conclusion, it is confirmed that the larger wave pressure occurs at the front wall of caisson around the still water level than the original design conditions when it generates the shock-crushing wave pressure checked by not two-dimensional analysis, but three-dimensional analysis through the change of wave pressure applied to the caisson along the length of breakwater.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.531-552
• /
• 2020

In the previous study, both the wave characteristics at the tip of composite breakwater and on caisson were investigated by applying olaFlow numerical model of three-dimensional regular waves. In this paper, the same numerical model and layout/shape of composite breakwater as applied the previous study under the action of one directional irregular waves were used to analyze two and three-dimensional spatial change of wave force including the impulsive breaking wave pressure applied to trunk of breakwater, the effect of rear region, and the occurrence of diffracted waves at the tip of caisson located on the high crested rubble mound. In addition, the frequency spectrum, mean significant wave height, mean horizontal velocity, and mean turbulent kinetic energy through the numerical analysis were studied. In conclusion, the larger wave pressure occurs at the front wall of caisson around the still water level than the original design conditions when it generates the shock-crushing wave pressure in three-dimensional analysis condition. Which was not occurred by two-dimensional analysis. Furthermore, it was confirmed that the wave pressure distribution at the caisson changes along the length of breakwater when the same significant incident wave was applied to the caisson. Although there is difference in magnitude, but its variation shows the similar tendency with the case of previous study.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.5 no.2
• /
• pp.66-75
• /
• 1993

Hydraulic experiments were performed in order to gain an insight into the quantitative differences between the perforated wall caisson and its solid wall counterpart in the local pressure distribution and caisson stability. The results showed that the wave forces acting on local walls were smaller in the perforated wall caisson than in the solid wall caisson. For the caisson stability, the critical weights of the perforated wall caisson also turned out to be smaller than those of the solid wall caisson. The Phenomenon was attributed to the dual effects inherent to the perforated wall caisson, which are the decrease of total horizontal force and the phase difference between the total horizontal and vertical forces.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.5
• /
• pp.725-734
• /
• 2010

This study conducted hydraulic testing to assess the stability of two types of pyramid-shaped artificial reefs (ARs) constructed to promote the growth of shellfish and seaweed. Previous theoretical and hydraulic experimental studies have clearly demonstrated Froude similitude. The results of this study revealed that some dimensionless design parameters affected the stability of both types of artificial reefs under various wave and current field conditions (e.g., surf similarity parameters, water particle velocity, wave pressure). In the fixed bed condition, the dimensionless water particle velocity based on the surf similarity parameter was large (about 0.4), and in the moveable bed condition, the relative water depth based on the dimensionless wave pressure was low (about 0.11). In addition, horizontal wave pressure and uplift pressure varied by relative water depth, demonstrating the tendency for wave pressure to decrease linearly with increased relative depth. These findings indicate that the development of more stable design technology forartificial reefs should be based on long-term data and additional study of sliding due to wave action. The findings also highlight the importance of hydraulic experiments in solving problems that have emerged in the design and construction of artificial reefs.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.3
• /
• pp.161-169
• /
• 2020

Physical experiments have been performed in a wave basin to investigate change of the wave loading on the crown wall under obliquely incident wave conditions. The measurement was carried out with wave incidence angle of 0, 15, 30 and 45°. The pressure transducers were placed on the front and bottom face of the crown wall to obtain horizontal and uplift force as well. It was found that both the horizontal and vertical force decreases with the incidence angle. Based on the analysis of the experimental data, a formula was suggested to estimate the reduction rate of horizontal and vertical forces under obliquely incident waves.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.3
• /
• pp.209-218
• /
• 2011

The present study proposes a new estimation relationship for the transmission rate of the steel breakwater which is expected to make up for the weakness points in existing hard solution for shore protection. The steel breakwater consists of the wave dissipator of the dual horizontal plates, the supporting columns and their foundations, and thus its respective designs should also be conducted one by one. Furthermore, the breakwater has to ensure both functions of shore protection and structure stabilization. The study produced experimental data for the stability and safety investigation of the steel breakwater. The forces acting on the steel breakwater were classified into two categories, one is vertical up and down loads for the pile resistance and the other was maximum difference of the vertical load acting on horizontally different position for the torsion. The study applied the stability force produced by the summation of maximum pressure at each point and the safety force acting on each point simultaneously. The regular wave corresponding to the significant wave was utilized for measuring wave pressure and force. The study showed the method for the proper position of submerged upper plate by considering occurrence frequency of tide level. The design process finally determined by trial and error is proposed in the present study.

• Journal of the Korean Geosynthetics Society
• /
• v.20 no.4
• /
• pp.105-112
• /
• 2021

In the case of harbor structures, it is important to understand the characteristics of structures that are subjected to repeated loads as they are structures that receive repetitive loads such as wave pressure as well as static loads. In this study, the lateral resistance according to the pile embeded depth of the block breakwater reinforced with piles by cyclic lateral loads was obtained through an model experiment. As the depth of embedment of the pile increased, the lateral resistance showed a tendency to increase. As the load was repeated, the gradient of the lateral resistance gradually appeared to be gentle. The bending moment of the rear pile was larger than that of the front pile. The bending moment of piles in the ground was similar to that when the pile head was free in the cohesionless of Broms (1964).